Search NASA⌕ Search

Engineering topics

Bumble, B.

Publications and source records attributed to Bumble, B..

59 records · Page 4

Dispersion in Nb microstrip transmission lines at submillimeter wave frequencies

We have measured the effects of dispersion on the resonant mode frequencies of open-ended Nb-SiO(x)-Nb microstrip transmission lines over a frequency range from 50 to 800 GHz. Submicron Nb/Al-AlOx/Nb Josephson junctions were used as both voltage-controlled oscillators and detectors to sample the high order modes of the resonators. The resonator modes are equally spaced up to about 550 GHz where the mode spacing start to decrease gradually to a minimum above the gap frequency of about 700 GHz and then increases. Results are in good agreement with the expected theoretical behavior based on the Mattis-Bardeen conductivity of the superconductor line.

Javadi, H. H. S.↗

A low noise 230 GHz heterodyne receiver employing .25 sq micron area Nb/AlO(x)/Nb tunnel junctions

Recent results for a full height rectangular waveguide mixer with an integrated IF matching network are reported. Two 0.25 sq micron Nb/AlO(x)/Nb superconducting insulating superconducting (SIS) tunnel junctions with a current density of about 8500 A/sq cm and omega RC of about 2.5 at 230 GHz have been tested. Detailed measurements of the receiver noise have been made from 200-290 GHz for both junctions at 4.2 K. The lowest receiver noise temperatures were recorded at 239 GHz, measuring 48 K DSB at 4.2 K and 40 K DSB at 2.1 K. The 230 GHz receiver incorporates a one octave wide integrated low pass filter and matching network which transforms the pumped IF junction impedance to 50 ohms over a wide range of impedances.

Kooi, Jacob W.↗

Onset of dispersion in Nb microstrip transmission lines at submillimeter wave frequencies

We have measured the dispersion in phase velocity of a Nb-SiO(x)-Nb microstrip transmission line resonator over a frequency range from 50 GHz to 800 GHz. A submicron Nb/Al-AlO(x)/Nb Josephson junction was used as a voltage-controlled oscillator to excite the high order modes in the resonator. The same junction is used as a direct detector resulting in a series of step-like structures in the DC current-voltage characteristic at the position of each mode frequency. The transmission line is dispersionless up to about 500 GHz where the phase velocity begins to decrease. This is well below the gap frequency f(sub g) approx. equals 700 GHz. Results agree qualitatively with the expected theoretical behavior near f(sub g). This onset of dispersion and loss in Nb transmission lines will have a significant impact on the design of submillimeter wave RF circuits.

Javadi, H. H. S.↗

Sub micron area Nb/AlO(x)/Nb tunnel junctions for submillimeter mixer applications

In this paper, we report on a fabrication process developed for submicron area tunnel junctions. We have fabricated Nb/AlO(x)/Nb tunnel junctions with areas down to 0.1 sq micron using these techniques. The devices have shown excellent performance in receiver systems up to 500 GHz and are currently in use in radio astronomy observatories at 115, 230, and 500 GHz.

Leduc, Henry G.↗

Submicron area NbN/MgO/NbN tunnel junctions for SIS mixer applications

The development of submicron area mixer elements for operation in the submillimeter wave range is discussed. High-current-density NbN/MgO/NbN tunnel junctions with areas down to 0.1 sq microns have been fabricated in both planar and edge geometries. The planar junctions were fabricated from in situ deposited trilayers using electron-beam lithography to pattern submicron area mesas. Modifications of fabrication techniques used in larger-area NbN tunnel junctions are required and are discussed. The NbN/MgO/NbN edge junction process using sapphire substrates has been transferred to technologically important quartz substrates using MgO buffer layers to minimize substrate interactions. The two junction geometries are compared and contrasted in the context of submillimeter wave mixer applications.

Leduc, H. G.↗