Search NASA⌕ Search

Engineering topics

Bykov, I.

Publications and source records attributed to Bykov, I..

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

DIII-D research to provide solutions for ITER and fusion energy

The DIII-D tokamak has elucidated crucial physics and developed projectable solutions for ITER and fusion power plants in the key areas of core performance, boundary heat and particle transport, and integrated scenario operation, with closing the core-edge integration knowledge gap being the overarching mission. New experimental validation of high-fidelity, multi-channel, non-linear gyrokinetic turbulent transport models for ITER provides strong confidence it will achieve Q ≥ 10 operation. Experiments identify options for easing H-mode access in hydrogen, and give new insight into the isotopic dependence of transport and confinement. Analysis of 2,1 islands in unoptimized low-torque IBS demonstration discharges suggests their onset time occurs randomly in the constant β phase, most often triggered by non-linear 3-wave coupling, thus identifying an NTM seeding mechanism to avoid. Pure deuterium SPI for disruption mitigation is shown to provide favorable slow cooling, but poor core assimilation, suggesting paths for improved SPI on ITER. At the boundary, measured neutral density and ionization source fluxes are strongly poloidally asymmetric, implying a 2D treatment is needed to model pedestal fuelling. Detailed measurements of pedestal and SOL quantities and impurity charge state radiation in detached divertors has validated edge fluid modelling and new self-consistent 'pedestal-to-divertor' integrated modeling that can be used to optimize reactors. New feedback adaptive ELM control minimizes confinement reduction, and RMP ELM suppression with sustained high core performance was obtained for the first time with the outer strike point in a W-coated, compact and unpumped small-angle slot divertor. Advances have been made in integrated operational scenarios for ITER and power plants. Wide pedestal intrinsically ELM-free QH-modes are produced with more reactor-relevant conditions, Low torque IBS with W-equivalent radiators can exhibit predator-prey oscillations in Te and radiation which need control. High-β P scenarios with q min > 2, q 95 –7.9, β N > 4, β T –3.3% and H 98y2 > 1.5 are sustained with high density ($\overline{n}$ = 7E19 m -3 , f G –1) for 6 τ E , improving confidence in steady-state tokamak reactors. Diverted NT plasmas achieve high core performance with a non-ELMing edge, offering a possible highly attractive core-edge integration solution for reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Power and isotope effects in the ITER baseline scenario with tungsten and tungsten-equivalent radiators in DIII-D

Abstract Experiments in DIII-D document the ITER Baseline Scenario (IBS) at q 95 ∼ 3 and P IN / P LH ∼ 1–2, in both deuterium and hydrogen utilizing Kr and Xe as Tungsten-equivalent radiators. The power threshold for H-mode operation ( P LH ) was determined experimentally without added impurities and found to be about a factor of two higher than the scaling law. In recent IBS experiments in deuterium, intrinsic levels of metals such as Tungsten (W) or molybdenum and inconel are present that reduce the pedestal pressure by 20%–25%. A complete radiative collapse of deuterium IBS plasmas occurs at W core concentrations C W = 10 −5 . Simulations show that for core temperatures expected for ITER, the plasmas would not have a radiative collapse at C W = 1 × 10 −5 , moreover Q = 8–10 would still be achieved for C W up to 3 × 10 −5 . In contrast to deuterium, the IBS in hydrogen is not affected by intrinsic high-Z impurities, indicating that hydrogen H-modes in ITER may not inform the D-T phase with respect to W accumulation and discharge survival. Compared to deuterium, the pedestal pressure in hydrogen is ∼25% lower, with much higher ELM frequency of 150 Hz, decreasing with input power. Krypton was injected in a matrix scan of input power and impurity flow in IBS hydrogen discharges. Krypton impurity density profiles in hydrogen are similar to deuterium plasmas, but at Kr flows that are 2–3 times higher for the same input power. Krypton is transported into the core and affects the whole radius; at the highest injection rates a radiative collapse occurs at core radiation fractions of 0.3–0.35, consistent with the expected maximum W radiation fraction for ITER core plasmas. Comparing the results with previous International Tokamak Physics Activity database studies of the IBS confirms that at higher radiation fraction due to high-Z impurities, a drop in H 98 of >10% is observed. On the other hand, the results using Kr as a W-equivalent radiator indicate that metal (W) devices at lower core temperatures than ITER may provide overly pessimistic performance extrapolations to ITER for deuterium-tritium operation. The new DIII-D results support a more attractive option for the ITER Research Plan with a short hydrogen phase for system commissioning, transitioning to deuterium operations as soon as possible to provide relevant conditions for deuterium-tritium operations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Recent DIII-D progress toward validating models of tungsten erosion, re-deposition, and migration for application to next-step fusion devices

Abstract Fundamental mechanisms governing the erosion and prompt re-deposition of tungsten impurities in tokamak divertors are identified and analyzed to inform the lifetime of tungsten plasma-facing components in ITER and other future devices. Various experiments conducted at DIII-D to benchmark predictive models are presented, leveraging the DiMES removable sample exposure probe capability and the Metal Rings Campaign, in which toroidally symmetric rows of tungsten-coated tiles were installed in the DIII-D divertor. In tokamak divertors, the width of the electric sheath is of the order of the main ion Larmor radius, and a vast majority of sputtered tungsten impurities are typically ionized within the sheath. Therefore, W prompt redeposition is mainly governed by the ratio of the characteristic ionization mean-free path of neutral tungsten to the width of the sheath. In-situ monitoring of the prompt redeposition of tungsten impurities in divertors is demonstrated via the use of WII/WI line ratios and the ionizations/photon (S/XB) method in L-mode discharges. Even with this relatively limited set of emission measurements, net erosion measurements were found to be a consistent upper bound to an analytic scaling based on the ratio of the W ionization length, λ iz , and the width of the magnetic sheath rather than the ratio of λ iz and the W + gyro-radius. In the far-scrape-off layer (SOL) of the ITER divertor, however, it is calculated that the measurement of photon emissions associated with the ionization of tungsten impurities up to W 5 + may be required. Finally, W deposition patterns on DiMES collector probes, interpreted via DIVIMP-WallDYN modelling, reveal the key roles of progressive W erosion/re-deposition staps and E × B drifts in regulating long-range high-Z material migration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Abstract Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from 3.9– 7.5 × 10 19 m −3 and input powers ranging from 5.5 to 9 MW. The small Si pellets were delivered with the impurity granule injector at frequencies ranging from 4 to 16 Hz corresponding to mass flow rates of 5–19 mg s −1 (1– 4.2 × 10 20 Si s −1 ) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO 2 is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least 0.4–1.2 nm thickness have been deposited at 0.4–0.7 nm s −1 . The technique is estimated to coat a surface area of at least 0.94 m 2 on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Measurements and modeling of type-I and type-II ELMs heat flux to the DIII-D divertor

Type-I and type-II edge-localized-modes (ELMs) heat flux profiles measured at the DIII-D divertor feature a peak in the vicinity of the strike-point and a plateau in the scrape-off-layer (SOL), which extends to the first wall. The plateau is present in attached and detached divertors and it is found to originate with plasma bursts upstream in the SOL. The integrated ELM heat flux is distributed at ~65% in the peak and ~35% in this plateau. The parallel loss model, currently used at ITER to predict power loads to the walls, is benchmarked using these results in the primary and secondary divertors with unprecedented constraints using experimental input data for ELM size, radial velocity, energy, electron temperature and density, heat flux footprints and number of filaments. The model can reproduce the experimental near-SOL peak within ~20%, but cannot match the SOL plateau. Employing a two-component approach for the ELM radial velocity, as guided by intermittent data, the full radial heat flux profile can be well matched. The ELM-averaged radial velocity at the separatrix, which explains profile widening, increases from ~0.2 km s –1 in attached to ~0.8 km s –1 in detached scenarios, as the ELM filaments' path becomes electrically disconnected from the sheath at the target. The results presented here indicate filaments fragmentation as a possible mechanism for ELM transport to the far-SOL and provide evidence on the beneficial role of detachment to mitigate ELM flux in the divertor far-SOL. However, these findings imply that wall regions far from the strike points in future machines should be designed to withstand significant heat flux, even for small-ELM regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

The fast camera (Fastcam) imaging diagnostic systems on the DIII-D tokamak

Two camera systems are installed on the DIII-D tokamak at the toroidal positions of 90° (90° system) and 225° (225° system), respectively. The cameras have two types of relay optics, namely, a coherent optical fiber bundle and a periscope system. The periscope system provides absolute intensity calibration stability while sacrificing resolution (10 lp/mm), while the fiber system provides high resolution (16 lp/mm) while sacrificing calibration stability. The periscope is available only for the 90° system. The optics of the 225° system were designed for view stability, repeatability, and easy maintenance. The cameras are located inside optimized neutron, x ray and magnetic shielding in order to reduce electronics damage, reboots, and magnetic and neutron interference, increasing the overall system reliability. An automated filter wheel, providing remote filter change, allows for remote wavelength selection. A software suite automates camera acquisition and data storage, allowing for remote operation and reduced operator involvement. System metadata is used to streamline the data analysis workflow, particularly for intensity calibration. Here, the spatial calibration uses multiple observable wall features, resulting in a reconstruction accuracy ≤2 cm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Misalignment of magnetic field in DIII-D assessed by post-mortem analysis of divertor targets

Abstract We assess the toroidal magnetic field B t asymmetry in DIII-D due to a misalignment of the toroidal field coils with respect to the poloidal magnetic field coils and vacuum vessel. The peak-to-peak variation of the divertor strike point (SP) radius is measured to be 1 cm, with an n = 1 toroidal pattern. We use the centre of a narrow carbon deposition band on tungsten-coated divertor tiles just inside the outer strike point (OSP) as a proxy for the divertor SP location. The band occurred in a series of reverse B t discharges with the OSP positioned on the divertor inserts due to strong E × B drift transport of C from the inner to the outer SP through the private flux region. The variation in band radius (and hence the magnetic SP) is a (4.89 ± 0.31) mm shift toward (310 ± 4)° toroidal direction. These measurements agree well with previous measurements of the 3D magnetic field distribution (Luxon 2003 Nucl. Fusion 43 1813), simulations performed by the mafot field line integration code, and recent Langmuir probe measurements in the small-angle-slot (SAS) divertor (Watkins et al 2019 Nucl. Mater. Energy 18 46). Comparison of these measurements in the SAS divertor also indicates that there is the possibility of a tilt (in conjunction with the shift) of the B t coil field of (0.04 ± 0.07)° towards the toroidal angle of (215 ± 25)°. Previous measurements suggested a field misalignment of (4.6 ± 0.3) mm in the 270° toroidal direction, and a tilt of (0.06 ± 0.02)° toward the 114° toroidal direction, which is similar to the results reported here. These studies will be important for better understanding the radial variation of the toroidal strike line in DIII-D, for designing the new generation of SAS divertor, and for developing an understanding of the impact of error fields on tokamaks with tightly baffled slot divertors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Investigation of core impurity transport in DIII-D diverted negative triangularity plasmas

Abstract Tokamak operation at negative triangularity has been shown to offer high energy confinement without the typical disadvantages of edge pedestals (Marinoni et al 2021 Nucl. Fusion 61 116010). In this paper, we examine impurity transport in DIII-D diverted negative triangularity experiments. Analysis of charge exchange recombination spectroscopy reveals flat or hollow carbon density profiles in the core, and impurity confinement times consistently shorter than energy confinement times. Bayesian inferences of impurity transport coefficients based on laser blow-off injections and forward modeling via the Aurora package (Sciortino et al 2021 Plasma Phys. Control. Fusion 63 112001) show core cross-field diffusion to be higher in L-mode than in H-mode. Impurity profile shapes remain flat or hollow in all cases. Inferred radial profiles of diffusion and convection are compared to neoclassical, quasilinear gyrofluid, and nonlinear gyrokinetic simulations. Heat transport is observed to be better captured by reduced turbulence models with respect to particle transport. State-of-the-art gyrokinetic modeling compares favorably with measurements across multiple transport channels. Overall, these results suggest that diverted negative triangularity discharges may offer a path to a highly-radiative L-mode scenario with high core performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Mitigation of plasma–wall interactions with low-Z powders in DIII-D high confinement plasmas

Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in H-mode plasmas (I p = 1 MA, B t = 2 T, P NB = 6 MW, < n e > = 3.6–5.0 · 10 19 m –3 ) into the upper small-angle slot divertor for 2 s intervals at constant rates of 3–204 mg s –1 . The multi-species BN powders at a rate of 54 mg s –1 showed the most substantial increase in divertor neutral compression by more than an order of magnitude and lasting detachment with minor degradation of the stored magnetic energy W mhd by 5%. Rates of 204 mg s –1 of boron nitride powder further reduce edge localized mode-fluxes on the divertor but also cause a drop in confinement performance by 24% due to the onset of an n = 2 tearing mode. The application of powders also showed a substantial improvement of wall conditions manifesting in reduced wall fueling source and intrinsic carbon and oxygen content in response to the cumulative injection of non-recycling materials. Furthermore, the results suggest that low-Z powder injection, including mixed element compounds, is a promising new core-edge compatible technique that simultaneously enables divertor detachment and improves wall conditions during high confinement operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Quantifying heat and particle flux to primary and secondary divertors for various types of edge-localized-modes

Between 15% and 30% of edge-localized-mode (ELM) heat flux can be deposited to regions outside the main divertor including the far scrape-off-layer (SOL), private flux region (PFR), and secondary divertor inner target. Analysis shown here demonstrates that type-I and small ELM plasmas are transported to the PFR and to the secondary inner divertor, which is magnetically isolated from the outer divertor, leading to well-defined heat flux profiles and with peak values that can surpass those at the secondary outer target. Such features are consistently observed for pedestal collisionalities from $ν$$^{*}_{e}$ ~1.5 to $ν$$^{*}_{e}$ ~3.9. Heat flux profiles of the examined ELM types feature rippled structures due to bursts in the outer far-SOL region but not on the secondary inner target, causing long decay lengths in the time-averaged ELM profiles. The contribution of each ELM type to the total time-averaged power deposited to the secondary divertor has been evaluated, showing that grassy ELMs contribute ~8%, small ELMs ~67%, and type-I ELMs ~85%. These findings imply that small ELMs may yet pose a concern for future machines if some regions of the main wall are not designed to withstand significant heat and particle fluxes. Due to the low intra-ELM heat flux contribution, however, the grassy ELM regime is an attractive option for an ELMing scenario in future machines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy

DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L–H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ~8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Developing solid-surface plasma facing components for pilot plants and reactors with replenishable wall claddings and continuous surface conditioning. Part A: concepts and questions

Abstract It is estimated that pilot plants and reactors may experience rates of net erosion and deposition of solid plasma facing component (PFC) material of 10 3 –10 5 kg yr −1 . Even if the net erosion (wear) problem can be solved, the redeposition of so much material has the potential for major interference with operation, including disruptions due to so-called ‘unidentified flying objects (UFOs)’ and unsafe dust levels. The potential implications appear to be no less serious than for plasma contact with the divertor target: a dust explosion or a major UFO-disruption could be as damaging for an actively-cooled deuterium-tritium (DT) tokamak as target failure. It will therefore be necessary to manage material deposits to prevent their fouling operation. This situation appears to require a fundamental paradigm shift with regard to meeting the challenge of taming the plasma–material interface: it appears that any acceptable solid PFC material will in effect be flow-through , like liquid–metal PFCs, although at far lower mass flow rates. Solid PFC material will have to be treated as a consumable , like brake pads in cars. ITER will use high-Z (tungsten) armor on the divertor targets and low-Z (beryllium) on the main walls. The ARIES-AT reactor design calls for a similar arrangement, but with SiC cladding on the main walls. Non-metallic low-Z refractory materials such as ceramics (graphite, SiC, etc) used as in situ replenishable, relatively thin—of order mm—claddings on a substrate which is resistant to neutron damage could provide a potential solution for the main walls, while reducing the risk of degrading the confined plasma. Separately, wall conditioning has proven essential for achieving high performance. For DT devices, however, standard methods appear to be unworkable, but recently powder droppers injecting low-Z material ∼continuously into discharges have been quite effective and may be usable in DT devices as well. The resulting massive generation of low-Z debris, however, has the same potential to seriously disrupt operation as noted above. Powder droppers provide a unique opportunity to carry out controlled studies on the management of low-Z slag in all current tokamaks, independent of whether their protection tiles use low-Z or high-Z material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Studies of EC pre-ionization in DIII-D to support development of ITER plasma initiation

New experiments have been conducted at DIII-D to improve the physics understanding of plasma initiation assisted by electron cyclotron (EC) wave injection, allowing better extrapolation to ITER. This has been achieved by applying an EC pulse prior to start of the inductive plasma initiation (i.e. the generation of a loop voltage). A pre-plasma was formed during the EC pulse that was characterized in terms of the maximum density and temperature. Parametric scans were performed to study the influence of the EC injected power, EC injection angle, and pre-fill gas pressure on the pre-plasma creation process. These experiments showed that pre-ionized plasma of good quality can have a significant effect on the subsequent V loop induced plasma initiation process, i.e. a high density pre-plasma, increases the plasma current rise and speed at which ionization is achieved when the V loop is applied. Here, a good quality pre-plasma is one that achieved a significant degree of ionization, mainly obtained by providing sufficient ECH power in DIII-D of the order of 1 MW. It was found that a minimum EC power of 0.5 MW was required in DIII-D to create ionization, and this would scale to a minimum power of roughly 6.5 MW for ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Developing solid-surface plasma facing components for pilot plants and reactors with replenishable wall claddings and continuous surface conditioning. Part B: required research in present tokamaks

Abstract The companion part A paper (Stangeby et al 2022) reports a number of independent estimates indicating that high-duty-cycle DT tokamaks starting with pilot plants will likely experience rates of net erosion and deposition of solid PFC, plasma facing component, material in the range of 10 3 to 10 4 kg yr −1 , regardless of the material used. The subsequent redeposition of such large quantities of material has the potential for major interference with tokamak operation. Similar levels and issues will be involved if ∼continuous low-Z powder dropping is used for surface conditioning of DT tokamaks, independent of the material used for the PFC armor. In Stangeby et al (2022) (part A) it is proposed that for high-duty-cycle DT tokamaks, non-metallic low-Z refractory materials such as ceramics (graphite, SiC, etc) used as in situ replenishable, relatively thin—of order mm—claddings on a substrate which is resistant to neutron damage could provide a potential solution for protecting the main walls, while reducing the risk of degrading the confined plasma. Assessment of whether such an approach is viable will require information, much of which is not available today. Section 6 of part A identifies a partial list of major physics questions that will need to be answered in order to make an informed assessment. This part B report describes R&D needed to be done in present tokamaks in order to answer many of these questions. Most of the required R&D is to establish better understanding of low-Z slag generation and to identify means to safely manage it. Powder droppers provide a unique opportunity to carry out controlled studies on the management of low-Z slag in current tokamaks, independent of whether their protection tiles use low-Z or high-Z material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗