Search NASA⌕ Search

Engineering topics

Bykov, I.

Publications and source records attributed to Bykov, I..

At least 37 records · Page 2

Testing the DIII-D co/counter off-axis neutral beam injected power and ability to balance injected torque

DIII-D has undergone a major upgrade and successfully injected high power off-axis neutral beams (~4 MW) in both co-current and counter-current directions. This capability of high power co/counter steerable off-axis neutral beams on a major tokamak opens a unique parameter space of broad pressure and current profiles for high beta steady-state advanced tokamak (AT) scenarios, while retaining the ability to balance the injected torque for low rotation studies. This co/counter off-axis neutral beam capability is being used to validate physics-based energetic particle and thermal transport models for designing next-step facilities based on the steady-state AT approach. This paper reports on the critical evaluation of the transmitted power and energetic ion population produced by this heating and current drive system, which is assessed through visible imaging, neutron measurements and rotation profile measurements at balanced torque. Minimal losses of neutral beam power have been achieved by optimizing the strongly focused ion sources required to pass through the aperture. Tilting of the ion source has been guided by fast visible imaging and resulted in neutral beam injection along the design centerline with empirical characterization of each beam's divergence derived from the imaging data and used in the NUBEAM description of the beam injection. Through exclusive power injection of each neutral beam into MHD quiescent plasmas across a range of neutral beam voltage, perveance and plasma current we conclude that a modest reduction (~10%–15%) of transmitted power compared to on-axis, standard focus has been incurred. We report corrections that more accurately represent the injected power. Good ability to balance the neutral beam torque has been demonstrated by injecting the new off-axis counter injecting beam against the existing off-axis co-injected beam in 2.0 T, 1.0 MA, MHD quiescent L-mode plasmas. Furthermore, the torque balance studies verify the ability to operate with balanced injection, which is critical for achieving low torque and low rotation operation for physics studies and in ITER demonstration discharges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Estimate of pre-thermal quench non-thermal electron density profile during Ar pellet shutdowns of low-density target plasmas in DIII-D

The radial density profile of pre-thermal quench (pre-TQ) early-time runaway electrons (REs) is estimated by combining electron cyclotron emission (ECE) and soft x-ray (SXR) data during rapid shutdown of low-density (n e ≲ 10 13 cm -3 ) DIII-D target plasmas with cryogenic argon pellet injection. This technique is limited in these experiments to the pre-TQ phase and quickly loses validity during the TQ. Two different cases are studied: a high (10 keV) temperature target and a lower (4 keV) temperature target. The results indicate that early-time, low-energy (~10 keV) REs form ahead of the argon pellet as it enters the plasma, affecting the pellet ablation rate; it is hypothesized that this may be caused by rapid cross-field transport of argon ions ahead of the pellet. Fokker-Planck modeling of the two shots suggests that the RE current is quite significant during the pre-TQ phase (up to 50% of the total current). Comparison between modeled pre-TQ RE current and post-TQ RE current inferred from avalanche theory suggests that RE current increases during the high temperature target TQ but decreases during the low temperature target TQ. Here, the uncertainties in this estimate are large; but, if true, this suggests that TQ loss of REs can be larger than previously estimated in DIII-D.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modelling dust transport in DIII-D with DTOKS-Upgrade

Comprehensive upgrades to the dust transport code Dust in TOKamaks (DTOKS) that extend the plasma-dust interaction model are presented and compared with recent measurements of dust transport in DIII-D. Simulations incorporating variation in physical properties of graphite dust with temperature and size in a stationary plasma background suggest a substantial decrease in lifetimes due principally to thermal expansion. The trajectories of 53 dust grains identified from analysis of visible camera data taken across two similar shots were used to measure the dust particle velocity distributions. Dust tracks terminated mostly at the outer divertor strike point having a mean observation time of 2.1 ± 0.4 ms. Stochastic modelling of 200 graphite dust particles in the DIII-D tokamak performed with DTOKS-U using plasma simulations generated by OEDGE found similar behaviour, with particles ablating rapidly after acquiring a positive charge in the region close to the outer strike point, creating an acute source of neutral carbon atoms. The simulated mean lifetime, 11 ± 2 ms, showed approximate agreement with experimental observation when corrected by accounting for dust visibility and ignoring the longest trajectories 1.5 ± 0.2 ms. Synthetic diagnostic data generated from coupling the results of DTOKS-U with the visualisation software Calcam offers a powerful new tool for validation of simulations and predictive calculations of dust dynamics.

Physics↗

Observation of non-thermal electron formation during the thermal quench of shattered pellet injection shutdowns in DIII-D

Formation of non-thermal (hot) electrons is studied during the thermal quench of shattered pellet injection (SPI) discharge shutdowns in the DIII-D tokamak. Both pure neon and mixed neon/deuterium shutdowns are studied. High-energy radiation (SXR and EUV) brightness levels show indications of non-thermal electron formation during the TQ. The non-thermal densities are of order 10 18 m –3 and non-thermal temperatures are estimated to be of order 10 keV. The non-thermal electrons appear to be mostly lost during the subsequent current quench, as no signal of relativistic runaway electrons is typically seen at the end of the current quench. In conclusion, the non-thermals appear to have an effect on the deposition profile of the SPI pellets, especially at the end of the TQ, due to increased pellet ablation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Robust impurity detection and tracking for tokamaks

A robust impurity detection and tracking code, able to generate large sets of dust tracks from tokamak camera footage, is presented. This machine learning–based code is tested with cameras from the Joint European Torus, Doublet-III-D, and Magnum-PSI and is able to generate dust tracks with a 65 – 100 % classification accuracy. Moreover, the number dust particles detected from a single camera shot can be up to the order of 1000. Several areas of improvement for the code are highlighted, such as generating more significant training data sets and accounting for selection biases. Finally, although the code is tested with dust in single two-dimensional camera views, it could easily be applied to multiple-camera stereoscopic reconstruction or nondust impurities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Runaway electron seed formation at reactor-relevant temperature

Systematic variation of the pre-disruption core electron temperature (T e ) from 1 to 12 keV using an internal transport barrier scenario reveals a dramatic increase in the production of ‘seed’ runaway electrons (REs), ultimately accessing near-complete conversion of the pre-disruption current into sub-MeV RE current. Injected Ar pellets are observed to ablate more intensely and promptly as T e rises. At high T e , the observed ablation exceeds predictions from published thermal ablation models. Simultaneously, the thermal quench (TQ) is observed to significantly shorten with increasing T e —a surprising result. While the reason for the shorter TQ is not yet understood, candidate mechanisms include: insufficiently accurate thermal ablation models, enhanced ablation driven by the seed RE population, or significant parallel heat transport along stochastic fields. Kinetic modeling that self-consistently treats the plasma cooling via radiation, the induced electric field, and the formation of the seed RE is performed. Including the combined effect of the inherent dependence of hot-tail RE seeding on T e together with the shortened TQ, modeling recovers the progression towards near-complete conversion of the pre-disruption current to RE current as T e rises. Measurement of the HXR spectrum during the early current quench (CQ) reveals a trend of decreasing energy with pre-disruption T e . At the very highest T e (≈ 12 keV), ≈ 100% conversion of the thermal current to runaway current is found. The energy of this peculiar RE beam is inferred to be sub-MeV as it emits vanishingly few MeV hard x-rays (HXRs). These measurements demonstrate novel TQ dynamics as Te is varied and illustrate the limitations of treating the RE seed formation problem without considering the inter-related dependencies of the pellet ablation, radiative energy loss, and resultant variations of the TQ duration. Finally, if the observed shortening of the TQ with increasing T e extends to fusion-grade plasmas, than their propensity to form large quantities of RE seeds at high T e may be far worse than previously thought. Positively, the high T e scenario in DIII-D produces REs so prodigiously that it can serve as a meaningful new platform for demonstrating RE avoidance techniques.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impact of divertor material on neutral recycling and discharge fueling in DIII-D

We report that experiments with the lower divertor of DIII-D during the Metal Rings Campaign (MRC) show that the fraction F of atomic D in the total recycling flux is material-dependent and varies through the ELM cycle, which may affect divertor fueling. Between ELMs, F C ~ 10% and FW ~ 40%, consistent with expectations if all atomic recycling is due to reflections. During ELMs, F C increases to 50% and F W to 60%. In contrast, the total D recycling coefficient including atoms and molecules R stays close to unity near the strike point where the surface is saturated with D. During ELMs, R can deviate from unity, increasing during high energy ELM-ion deposition (net D release) and decreasing at the end of the ELM which leads to ability of the target to trap the ELM-deposited D. The increase of R > 1 in response to an increase in ion impact energy Ei has been studied with small divertor target samples using Divertor Materials Evaluation System (DiMES). An electrostatic bias was applied to DiMES to change E i by 90 eV. On all studied materials including C, Mo, uncoated and W-coated TZM (>99% Mo, Ti, and Zr alloy), W, and W fuzz, an increase of E i transiently increased the D yield (and R) by ~10%. On C there was also an increase in the molecular D 2 yield, probably due to ion-induced D 2 desorption. Despite the measured increase in F on W compared to C, attached H-mode shots with OSP on W during MRC did not demonstrate a higher pedestal density. About 8% increase in the edge density could be seen only in attached L-mode scenarios. The difference can be explained by higher D trapping in the divertor and lower divertor fueling efficiency in H- versus L-mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enhanced helium exhaust during edge-localized mode suppression by resonant magnetic perturbations at DIII-D

Effective helium confinement time, τ p * ,He , and its ratio with energy confinement time, τ p * ,He / τ E , are key metrics quantifying the suitability of fusion plasmas for a continuous burn. Comparisons in the DIII-D tokamak of discharges with suppression of edge localized modes (ELMs) by resonant magnetic field perturbations (RMPs) to the corresponding unperturbed ELMy discharges found that both of these metrics were strongly reduced, by a factor of approximately 2, after application of the RMPs. This reduction in τ p * ,He during RMP ELM suppression was observed in the plasma core, edge, and pumping plenum, where higher neutral helium concentration during RMPs was also measured. In conclusion, these findings provide evidence that future devices employing RMP ELM suppression may meet or even exceed the helium exhaust provided by the ELMs themselves, reducing helium ash, and thus maintaining high fusion gain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Localized divertor leakage measurements using isotopic tungsten sources during edge-localized mode-y H-mode discharges on DIII-D

Experiments carried out on DIII-D using a novel setup of isotopic tungsten (W) sources in the outer divertor have characterized how the W leakage from this region depends on both the exact source location and edge-localized mode (ELM) behavior. The sources are toroidally-symmetric and poloidally-localized to two regions: (1) the outer strike point (OSP) with natural abundance of W isotopes; and (2) the far-target with highly-enriched 182 W isotopes. With the use of a dual-faced collector probe (CP) in the main scrape-off layer (SOL) near the outside midplane and source-rate spectroscopy, a proxy for divertor impurity leakage is developed herein. Using this proxy, it is found that for the OSP W location, there is a nearly linear increase of leakage with the power across the separatrix ( ), which is consistent with the effect of an increased upstream ion temperature parallel gradient force in the near-SOL; trends in the pedestal density and collisionality are also seen. Conversely, it is found that for the far-target W location leakage falls off rapidly as increases and ELM size decreases, which is suggestive that ELM size plays a role in the leakage from this location. Indications for main SOL W contamination is evidenced by the measurement of large deposition asymmetries on the two opposite CP faces. These measurements are coupled with interpretive modeling showing SOL W accumulation near the separatrix furthest from both targets driven by forces parallel to the magnetic field. This experimental setup, together with the target and upstream W measurements, provides information on the transport from different divertor W source locations and leakage. These studies help to elucidate the physics driving divertor impurity source rates and leakage, with and without ELMs, and provide better insight on the link in the chain connecting wall impurity sources to core impurity levels in magnetic fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ablation of solid pellets induced by supra-thermal ions in the far scrape-off layer of tokamak plasmas

Injection of solid pellets is a key element in several aspects of the operation of a magnetic confinement plasma reactor for fusion applications, including plasma fueling, control and diagnosis. This letter reports observations demonstrating that pellet ablation can begin outside the plasma boundary, by effect of supra-thermal ions, whose orbits, under appropriate conditions, can extend well into the vacuum region. The phenomenon was recorded during plasma discharges in the DIII-D tokamak, combining pulsed modulation of heating neutral beams, with high-frequency injection of sub-millimeter lithium pellets, and it is ascribed to the large fraction of trapped beam ions associated with counter current neutral beam injection. The effect was quantitatively evaluated by means of Monte-Carlo simulations of supra-thermal ion orbits, finding that the heat-deposition was of the order of 50-100 W/mm 2 , in the region traversed by the lithium pellets before reaching the plasma boundary, which is consistent with the severe pellet deterioration observed for low velocity pellets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

EDGE2D-EIRENE predictions of molecular emission in DIII-D high-recycling divertor plasmas

The contributions of deuterium molecular emission to the total deuterium radiation was assessed in DIII-D ohmically-confined plasmas in high-recycling divertor conditions. Radial profiles of the deuterium Ly-α line intensity across the low-field side divertor leg were obtained with the recently installed divertor Survey Poor Resolution, Extended Spectrometer [1]. A high-resolution spectrometer was used to measure the poloidal profiles of the deuterium Balmer-α and the deuterium Fulcher-α band intensity in the visible wavelength range. The scrape-off layer plasma and neutral distributions were simulated using the edge fluid EDGE2D-EIRENE [2], and the numerical solutions constrained utilizing Thomson scattering and Langmuir probe measurements at the low-field side midplane and the divertor target plate. The studies show that for these conditions molecular emission plays a negligible role in the total radiative power balance of the low-field side divertor, but molecular processes are important when evaluating deuterium Balmer-α line intensity for code-experiment validation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗