Search NASA⌕ Search

Engineering topics

Caldona, Eugene B.

Publications and source records attributed to Caldona, Eugene B..

At least 19 records

A magnetic‐directed micro‐particle with near‐ IR light triggered guest‐release property

Abstract In this study, guest carriers, composed of magnetic‐directed hydrogel particles with near‐infrared (NIR)‐light‐triggered guest‐release properties, are prepared via the one‐pot method. The gel particles contain photostable NIR‐responsive polypyrrole nanoparticles with temperature‐sensitive poly(N‐isopropyl acrylamide), the combination of which can induce the accelerated release of encapsulated drugs by 337% upon 5 minutes of NIR light irradiation based on the release profile of NRMG‐1 at 10–15 min. Additionally, with magnetic iron oxide particles crosslinking the polyvinyl alcohol frames, these gel particles can form a physical barrier that decreases the release rate by 20% under an external magnetic field over 24 h. The magnetic iron oxide particles also enable the gel particles to reach their target destination without extra drug losses.

60 APPLIED LIFE SCIENCES↗

Distinct Mechanism of Anti-Corrosion and Swelling-Adhesion Modeling of Low-Dimensional Nylon-Fluoropolymer Composite Coatings

Compared to other polymers, composite coatings with fluoropolymers as the matrix have attracted considerable interest due to their mechanical performance, chemical stability, and low surface energy. Herein, we present an anticorrosion mechanism of fluoropolymer composite coatings achieved by dispersing varying amounts of polyamide 12 (PA-12) particles over a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) matrix. The choice of PVDF-HFP as a coating matrix was driven by its superior processability and mechanical properties over Teflon, while PA-12 afforded swelling capacity, preventing electrolyte permeation, and inhibiting matrix stress crack propagation. The corrosion resistance of the coatings was assessed mainly by potentiodynamic polarization and impedance measurements while being immersed in a NaCl solution. Our electrochemical measurement findings showed that 0.75% w/w PA-12 in the PVDF-HFP matrix significantly enhanced corrosion protection even after 21 days of immersion. Microscopy, dielectric spectroscopy, surface analysis, and mechanical testing (American Society for Testing and Materials standards) corroborated the results. PVDF-HFP coatings containing a minimum percolation threshold of 0.75 wt % PA-12 with 1 mil thickness on mild steel exhibited a remarkable increase in resistance and film adhesion, and a notable corrosion rate decrease. Finite element analysis simulation with a bilinear traction-separation law confirmed the swelling mechanism and adhesion behavior. Finally, this study highlights the potential of nylon particle dispersion in PVDF-HFP matrices as a practical approach to developing advanced anticorrosion coatings with promising practical applications in various industries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

3D Temperature-Controlled Interchangeable Pattern for Size-Selective Nanoparticle Capture

Patterned surfaces with distinct regularity and structured arrangements have attracted great interest due to their extensive promising applications. Although colloidal patterning has conventionally been used to create such surfaces, herein, we introduce a novel 3D patterned poly(N-isopropylacrylamide) (PNIPAM) surface, synthesized by using a combination of colloidal templating and surface-initiated photoinduced electron transfer-reversible addition–fragmentation chain transfer (SI-PET-RAFT) polymerization. In order to investigate the temperature-driven 3D morphological variations at a lower critical solution temperature (LCST) of ~32 °C, multifaceted characterization techniques were employed. Atomic force microscopy confirmed the morphological transformations at 20 and 40 °C, while water contact angle measurements, upon heating, revealed distinct trends, offering insights into the correlation between surface wettability and topography adaptations. Moreover, quartz crystal microbalance with dissipation monitoring and electrochemical measurements were employed to detect the topographical adjustments of the unique hollow capsule structure within the LCST. Tests using different sizes of PSNPs shed light on the size-selective capture–release potential of the patterned PNIPAM, accentuating its biomimetic open–close behavior. Notably, our approach negates the necessity for expensive proteins, harnessing temperature adjustments to facilitate the noninvasive and efficient reversible capture and release of nanostructures. Finally, this advancement hopes to pave the way for future innovative cellular analysis platforms.

36 MATERIALS SCIENCE↗

On the 3D printing of polyelectrolyte complexes: A novel approach to overcome rheology constraints

Strong polyelectrolytes, poly(styrene sulfonate) (PSS), and poly(diallyldimethylammonium) (PDADMAC) dissolved in aqueous KBr can be 3D printed for the first time in the air via direct ink writing (DIW). Viscous polyelectrolyte complex (PEC) solutions were deposited layer-by-layer and quenched with deionized water to produce mechanically viable, viscoelastic hydrogel objects. Optimal inks were confirmed by rheology and thermogravimetric measurements to map flow behavior with material composition. Finally, post-print handling and storage protocols were developed to produce printed resolutions more consistent with conventional DIW.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Copper-nickel electroplating of 3D-printed acrylonitrile butadiene styrene for interference and radiation shielding applications

Here, in this study, electromagnetic and radiation shielding structures were fabricated by 3D printing acrylonitrile butadiene styrene (ABS) structures via fused filament fabrication and electroplating with copper (Cu) and nickel (Ni) metals. Prior to electroplating, the printed ABS materials were made conductive by surface electrodeposition of polypyrrole (PPy). ABS adsorbs the pyrrole monomer, which subsequently polymerizes via oxidation forming conductive PPy layer on the printed structures. The successful anchoring of PPy layer can be attributed to its hydrogen bonding and electrostatic interactions with ABS. Thermal analysis, optical, and electron microscopy equipped with energy dispersive X-ray were employed to characterize the printed shielding structures, while the interference and radiation shielding effectiveness were evaluated using a spectrum analyzer and dosimeter, respectively. The interference shielding was found to be effective at 60 ± 5 dB over relatively small frequency range. Shielding was also apparent against gamma and X-ray ionizing rays, but more significantly effective against beta rays. Furthermore, the Cu/Ni coating was able to reduce any heat-induced dimensional changes for the 3D printed ABS substrate without compromising the mechanical integrity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

PDMS ‐silica composite gas separation membranes by direct ink writing

Abstract Polydimethylsiloxane (PDMS)‐based membranes containing amine‐functionalized and unfunctionalized silica particles were fabricated via direct ink writing for CO 2 /N 2 gas separation. The printability of the inks was evaluated by rheological measurements, while spectroscopy, microscopy, thermal measurements, and mechanical testing were employed to characterize the printed membranes. The surface morphology of the membranes revealed the absence of voids, demonstrating their suitability for gas separation. The printed membranes also exhibited desirable thermal and mechanical properties (i.e., thermal degradation temperature of 518 °C and tensile strength as high as 1.178 MPa with 529% elongation). The PDMS‐based membranes generally displayed high permeability for CO 2 but slightly low selectivity for the CO 2 /N 2 gas pair. The best‐combined permeability‐selectivity performance of 8794 barrer and selectivity of 11.64 was demonstrated by the printed PDMS membrane containing no SiO 2 fillers. The inclusion of unfunctionalized SiO 2 particles generally increased the membrane's gas permeability but compromised the selectivity. In contrast, membranes with amine‐functionalized silica showed improved selectivity compared to membranes containing unfunctionalized silica. Overall, the performance and characteristics offered by the PDMS/silica composite membranes demonstrated the potential of 3D printing as an economical and sustainable fabrication approach to developing materials for carbon capture applications.

Gutierrez, Dianne B.↗

On the 3D printing of polypropylene and post-processing optimization of thermomechanical properties

Polypropylene (PP) is a highly desirable polyolefin in various plastic industries due to its outstanding thermomechanical properties and chemical resistance. Therefore, the 3D printing of PP is an interesting avenue to explore in digitized manufacturing, where more freedom in structural designs is available for new and extended applications, such as high-performance engineering parts. Here, in this work, we 3D printed PP and studied the effect of printing parameters and post-processing conditions on the printed polymer’s thermomechanical behavior. Results showed that nozzle and bed temperatures of 220 and 100°C produced a high printing quality. Infill percentages between 80 and 90%, coupled with a 4-h annealing at 110ºC, also resulted in optimal printed properties. It is thought that PP can be potentially blended with polyethylene or other vinyl polymers for a more extended 3D printing utility and practical applications in rapid tooling and prototyping.

36 MATERIALS SCIENCE↗

Synthesis of hyperbranched polymer films via electrodeposition and oxygen-tolerant surface-initiated photoinduced polymerization

Hypothesis Hyperbranched polymers, not only possess higher functionality, but are also easier to prepare compared to dendrimers and dendric polymers. Combining electrodeposition and surface-initiated photoinduced electron transfer-reversible addition-fragmentation chain transfer (SI-PET-RAFT) polymerization is hypothesized to be a novel strategy for preparing hyperbranched polymer films on conductive surfaces without degassing. Experiments In this study, polymer brush grafted films with four different architectures (i.e. linear, branched, linear- block -branched, and branched- block -linear) were prepared on gold-coated glass substrates using electrodeposition, followed by SI-PET-RAFT polymerization. The resulting film structure and thickness, surface topology, absorption property, and electrochemical behavior were confirmed by spectroscopy, microscopy, microbalance technique, and impedance measurement. Findings These hyperbranched polymer brushes were capable of forming a thicker but more uniformly covered films compared to linear polymer brush films, demonstrating that hyperbranched polymer films can be potentially useful for fabricating protective polymer coatings on various conductive surfaces.

36 MATERIALS SCIENCE↗

Corrosion-resistant polyurethane coatings from structure-homogenized biorefinery lignin through fractionation and oxypropylation

Using lignin for polyurethane (PU) synthesis is challenging because of its heterogeneous structure, i.e., broad molecule weight (MW) distribution and diverse hydroxyl (OH) functionality. This complexity influences the crosslinking reaction between lignin and isocyanate and affects the quality of PU products. Here, we propose a two-step strategy for lignin structure homogenization by lowering its MW and uniforming OH functionality (step 2). Step 1 involves a bioethanol fractionation process, yielding fractionated lignin with one order lower MW than the raw lignin while exhibiting better processability for the subsequent process. Step 2 is performed by an oxyalkylation process using fractionated lignin that converts phenolic and carboxylic OHs to aliphatic OHs. As a result, we obtained structure-homogenized lignin with good compatibility and crosslinking with hexamethylene diisocyanate for PU coating synthesis. Moreover, PU coatings prepared from structure-homogenized lignin display a defect-free microscopic structure and show better corrosion resistance than coatings fabricated from its raw lignin alternative. Overall, the structure homogenization process is a beneficial way of using lignin as biopolyol in PU synthesis toward the application-oriented design of corrosion-resistant lignin-based PU coatings.

36 MATERIALS SCIENCE↗

PET-RAFT polymerization under flow chemistry and surface-initiated reactions

Recently, photoinduced electron/energy transfer reversible addition–fragmentation chain transfer (PET-RAFT) polymerization has been developed and gaining wide acceptance. PET-RAFT polymerization uses visible light to initiate the reaction and is compatible with ambient conditions and green solvents. It also maintains the ability to produce well-defined polymers and possesses high potential as an alternative to the conventional RAFT technique. Here, this review aims to summarize the fundamentals of PET-RAFT polymerization, highlight two of the most commonly studied applications of PET-RAFT process (i.e. flow chemistry and surface-initiated polymerization), and explore perspectives and new possibilities of the technique.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hyperbranched PDMAEMA-functionalized SiO 2 microparticles: ATRP polymerization and grafting in a continuous flow reactor

Flow chemistry offers high reaction yield, kinetic control, improved safety, reliability, scalability, and greater degree of process control. Herein, hyperbranched polymer-grafted silica microparticles (HP-SMPs) are synthesized in a commercially available flow reactor through atom transfer radical polymerization. Initiator-anchored silica microparticles are obtained by in situ silanization in the flow reactor. Hyperbranched poly[2-(dimethylamino)ethylmethacrylate] chains are grafted onto the initiator-anchored SMPs through inimer–monomer ratio control. To demonstrate the efficiency and universality of this approach in grafting polymers onto SMPs, multiple hyperbranched polymeric structures are obtained by varying the inimer concentration. Dye absorption test is conducted to demonstrate the potential applications of HP-SMPs.

36 MATERIALS SCIENCE↗

Anticorrosive epoxy coatings from direct epoxidation of bioethanol fractionated lignin

The development of lignin-based anticorrosive epoxy coatings for steel protection is beneficial for both alleviating the fossil resource depletion and value-added utilization of lignin but remains a challenge due to the inherent heterogeneous structure of lignin. Here, in this study, we selectively extract the low molecular weight (MW) fraction of a crop residue-derived enzymatic hydrolysis lignin (EHL) through a bioethanol fractionation process and prepare epoxy resin by direct epoxidation of the bioethanol fractionated lignin (BFL). The coatings are then fabricated using 20–100 wt% of BFL-based epoxy resin (LEp) as the commercial epoxy resin substitute. The low MW and high p-hydroxyphenyl content of the BFL offer high solubility and good workability for BFL and LEp during epoxidation and coating production, respectively. Lignin-based coatings with 20–40 wt% LEp exhibit good adhesion property (5B) and superior corrosion resistance, compared to the commercial epoxy coating. Although coating with high LEp concentrations (i.e., 60–100 wt%) resulted in decreased adhesion strength, the coating with 100 wt% LEp still displayed corrosion protection performance comparable to that of the commercial epoxy coating. Overall, this study provides a simple and effective approach to converting lignin to epoxy resins for a wide variety of surface coating applications.

09 BIOMASS FUELS↗

SI-PET-RAFT Polymerization via Electrodeposited Macroinitiator Thin Films: Toward Biomedical and Sensing Applications

Surface-initiated photoinduced electron transfer-reversible addition–fragmentation chain transfer (SI-PET-RAFT) polymerization has been preferentially used for preparing thin polymeric film coatings due to its simple execution under ambient conditions (e.g., in air) and visible light requirement. In this study, we demonstrate the preparation of polymer brushes by SI-PET-RAFT polymerization on a thin macroinitiator film electrodeposited on electrically conductive indium tin oxide and gold surfaces. An electrochemically active carbazole-containing chain transfer agent as macroinitiator was shown to be not only effective in mediating SI-PET-RAFT polymerization for various monomers but also capable of forming block copolymers. Additionally, the fabricated polymer brush films were able to encapsulate colloidal gold nanoparticles, thereby demonstrating potential use for biomedical and sensing applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Grafted polythiophene pendent polymer brushes and their electronanopatterning

Here electrochemical nanolithography using grafted polymer brushes with terthiophene (3T) pendent was investigated. The film was fabricated by surface electropolymerization of a reversible addition-fragmentation chain-transfer agent macroinitiator containing a 3T pendant molecule and the subsequent polymer brush growth from a 3T functionalized methacrylate monomer (3T-Methacrylate). Electrochemical nanolithography and patterning were done using conducting atomic force microscopy (C-AFM) enabling precise nanopattern fabrication. In contrast to direct nanowriting, dip pen nanolithography, and nanolithographic additive manufacturing, the electrochemical nanolithography can be readily facilitated by applying a bias voltage between a conductive AFM tip and the grafted polymer brush film at ambient conditions and without ink transfer. The height and electrical resistance of the nanopatterns were dependent on the writing parameters (i.e. applied bias voltage and scan rate).

36 MATERIALS SCIENCE↗

On the Interfacial Behavior of Catenated Poly(l-lactide) at the Air–Water Interface

Interfacial properties of polymeric materials are significantly influenced by their architectural structures and spatial features, while such a study of topologically interesting macromolecules is rarely reported. Here, we reported, for the first time, the interfacial behavior of catenated poly(l-lactide) (C-PLA) at the air–water interface and compared it with its linear analogue (L-PLA). The isotherms of surface pressure–area per repeating unit showed significant interfacial behavioral differences between the two polymers with different topologies. Isobaric creep experiments and compression–expansion cycles also showed that C-PLA demonstrated higher stability at the air–water interface. Interestingly, when the films at different surface pressures were transferred via the Langmuir–Blodgett method, successive atomic force microscopy imaging displayed distinct nanomorphologies, in which the surface of C-PLA exhibited nanofibrous structures, while that of the L-PLA revealed a smoother topology with less fiber-like structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On the optimized 3D printing and post-processing of PETG materials

Glycol-modified polyethylene terephthalate (PETG) is a reliable middle ground between polylactic acid and acrylonitrile butadiene styrene due to its light weight, impact resistance, toughness, flexibility, and cost-effectiveness. However, during 3D printing, the filament form is prone to oozing and stringing. In this study, we optimized the PETG printability via g-code setting and printing parameter modification, and consideration of filament quality, build plate temperature and leveling, and printing design complexity. Printed PETGs were thermally and chemically annealed, and post-processing conditions including annealing time, temperature, and solvent use were investigated. Mechanical properties were evaluated in terms of print parameter changes and post-processing techniques.

36 MATERIALS SCIENCE↗

Mechanically and Thermally Enhanced 3D-Printed Photocurable Polymer Nanocomposites Containing Functionalized Chitin Nanowhiskers by Stereolithography

Additive manufacturing, or simply 3D printing (3DP), where objects are built through layer-wise material deposition, has gained significant academic and industrial attention as a result of the development of advanced and functional materials requiring rapid, customized, and flexible solutions. In the context of green manufacturing, diversifying environmentally and economically sustainable material portfolios is an essential endeavor for the success of 3DP technology that uses widely available, highly valuable, and renewable materials. Here, we used stereolithography (SLA) for processing methacrylate-based photocurable resins containing crab shell-derived chitin nanowhiskers (CNWs), which are surface-functionalized by reactive acrylate groups. Results from full spectral, thermal, structural, and topological analyses corroborate not only the surface functionalization of CNWs but also indicate the presence of these photocurable CNW (pCNW) fillers in the 3D-printed nanocomposites. Owing to the strong interfacial bond induced by the physical and chemical crosslinking between the pCNW and methacrylate (MA) polymer matrix, the internally formulated nanocomposites displayed enhanced thermomechanical properties (e.g., storage modulus and glass transition temperature) compared to those of commercially available pure SLA resins. For instance, the inclusion of 0.5 wt % pCNW improved the tensile strength and stiffness to up to 78 and 71%, respectively, without compromising the toughness and ductility of the printed material. Accordingly, this result also evidences the compatibility between the filler and resin materials. Consequently, the formation of a crosslinked network in the nanocomposite structure results in a higher thermal stability and activation energy (i.e., up to ~79%) for all the hybrid materials than the pristine MA. Finally, the high-resolution SLA print features, dimensional accuracy, and enhanced mechanical performance of our microstructure-forming functionalized chitin-based nanocomposites make them promising materials for a wide range of robust and high-performance industrial applications.

36 MATERIALS SCIENCE↗