Search NASA⌕ Search

Engineering topics

Cao, Yan

Publications and source records attributed to Cao, Yan.

At least 37 records · Page 2

Serpent transient analyses of GIACINT geometrical change experiments

This paper simulates seven transient experiments with geometrical movements performed at the GIACINT facility of Belarus. These experiments include three slow control rods insertion in more than 25 s, one fast control rod insertion in less than 1 s, and three water moderator draining transients. In the fast control rod insertion experiment, the control rods are first pushed by a mechanical spring and then let fall by gravity in the assembly. In this experiment, the control rods speed varies because of the initial spring force, the gravitational acceleration, and the water buoyancy force. In all other transient experiments, the geometry change occurs with a constant speed. The Serpent computer program was utilized to simulate these transient experiments with geometrical changes by performing two separate computations. One time-independent computation is performed in criticality mode and the other time-dependent computation is performed in dynamic-source mode. The first computation writes the neutron population and delayed neutron precursors for starting the transient simulation. The second computation divides the transient time into several time bins, reads the two files from the first computation, and updates them at the end of each time bin. The Serpent simulation results obtained for this set of experiments are in good agreement with the time dependent experimental measurements. In addition, Serpent and MCNP simulations results show an excellent agreement for the water moderator transient

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Validation of Spent Fuel Dose Rate Calculations Using NDA Measurement Campaign Data

The predicted radiation gamma dose rate is a key parameter to determine if a spent nuclear fuel assembly is self-protected from misuse as well as an indicator for worker/inspector safety. Recent studies showed that using state-of-the-art techniques for dose rate calculations, including the one adopted for this study, the numerical calculations of the gamma dose rates are three times lower than those from the most commonly-cited reference values for spent LWR fuel used by domestic and international agencies. With only a few publically available experimental data points worldwide for this type of benchmark study, the gamma flux measurements from the Spent Fuel Non Destructive Assay (NDA) measurement campaign can be used to help validate the physics approach used in calculating gamma dose rates. Specifically, this data would validate the gamma flux calculation from spent fuel, which is a key component of these multi-physics techniques for dose rate assessments; dose rate measurements were not part of the NDA campaign. These data are primarily the passive gamma measurements of the spent nuclear fuel assemblies from the Swedish Nuclear Fuel and Waste Management Company (SKB).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Monte Carlo fuel burnup analyses of the Accelerator-Driven Subcritical systems

Here, we discuss the Monte Carlo fuel burnup analysis performed for the Argonne National Laboratory (ANL) Accelerator-Driven Subcritical (ADS) conceptual design. The ANL ADS conceptual design was determined to dispose of the 131 tons of Minor Actinides (MA) fuel of the current United States Spent Nuclear Fuel (SNF) inventory. It uses a neutron source from 1 GeV 25MW proton beam with the liquid lead target to drive the subcritical fission assembly. It utilizes the liquid metal slurry fuel concept to load the MAs fuel. The subcritical fission assembly has a neutron multiplication factor of 0.98. The total fission power generated in the system is about 2.67 GW. The system is designed to operate for 35 full power years. Monte Carlo fuel burnup analyses were performed to calculate the amount of MAs consumed by the ANL ADS conceptual design. The MCNP6 computer program was used to simulate the high energy physics of the protons striking the liquid lead target for generating the neutron source. The MCB5 and SERPENT Monte Carlo burnup computer programs were used to simulate the fuel burnup during the ADS operation. In the ANL ADS conceptual configuration, the reactivity loss during the fuel burnup is compensated by adding fresh fuel into the subcritical assembly. In this paper, both batch and continuous fueling modes are examined. The fresh fuel particles are loaded into the slurry fuel carrier at the beginning of each burnup step of the batch-fueling mode and loaded continuously into the slurry fuel carrier during the operation in the continuous fueling mode. Monte Carlo fuel burnup analyses show that one ANL ADS conceptual design can consume about 25.7 tons of MAs fuel during the 35 full power years with the continuous fueling mode. About five units is required to dispose of the 131 tons of MAs

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Validation of Gamma Dose Rate Calculation Methodology using the Morris and Turkey Point Measurements

The ability to accurately predict the dose rates from the spent nuclear fuel assembly is very important for determining whether the used nuclear fuel is self-guarded and self-protected. Studies have shown that the direct numerical calculations of the dose rates gave a much lower value than a typical reference. This report summarizes the benchmark studies performed to evaluate the numerical methodologies used in calculating the gamma dose rates of the spent nuclear fuel assemblies. The Morris and Turkey Point experimental data for dose rates measured through air were used in the analyses. Numerical simulations of the gamma dose rate measurements included the fuel depletion analysis of the fuel assembly as well as its structural materials irradiated inside the reactor core, the radioisotopes decay, and photon transport simulations to calculate the gamma dose rates. The different factors which affect the calculated gamma dose rates were addressed. The calculated results were compared with the measured gamma dose rates. Good agreement was obtained when the detectors were placed at the middle of the fuel assembly region. The deviations of the calculated dose rates became larger when the measurements were performed at the top or bottom fuel assemblies. In these benchmark studies, the spent nuclear fuel assemblies were all PWR assemblies and had fuel burnup around 25 MWd/kg to 40 MWd/kg. Its cooling time before the measurements was around 1.8 years to 7 years. The used nuclear fuel assembly is usually self-protected while discharged from the core. Its radioactivity decreases and after a few tens of years it may fall down below the current threshold of 100 r/h. Future validation work is necessary in order to better evaluate the numerically calculated gamma dose rates with experiments performed for other types of fuel assemblies and for fuel assemblies with higher burnup and/or longer cooling times.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

First-principles study of thermal conductivities of uranium aluminides

Here, we investigate the lattice and electronic thermal conductivities of uranium aluminide compounds, i.e., UAl 2 , UAl 3 and UAl 4 , by density functional theory calculations. The lattice and electronic contributions to the total thermal conductivity of uranium aluminides are compared, and the contributions of phonons with different mean free times and modes to the lattice thermal conductivity of UAl 3 are analyzed from the calculated cumulative and spectral thermal conductivities. The effect of Mo alloying and U vacancy on the thermal conductivity of UAl 3 and UAl 4 is studied by considering the elastic phonon scattering due to mass difference. Both Mo alloying and U vacancy are found to significantly reduce the thermal conductivities of ideal UAl 3 and UAl 4 even with very low concentrations. The currently predicted thermal conductivities of uranium aluminide compounds are expected to be useful to the evaluation of the effective thermal conductivity of the interaction layer formed in U-Mo/Al dispersion fuel.

36 MATERIALS SCIENCE↗

IBR-2M Reactor Modeling with MCNP, SERPENT, CUBIT, and GIMP Computer Programs

IBR-2M is a fast research reactor located in Dubna (Russia), which operates in supercritical condition for ~800 μs every 200 ms. Two reflector parts are rotating in opposite directions generating 1.8 GWth peak power when the two parts align with the fuel zone. The reactor core uses plutonium fuel and sodium coolant. The control rods are located in stationary reflector zones. This report describes the computational modeling of the IBR-2M reactor. Two independent computational models were generated using MCNP and SERPENT computer programs. The MCNP model uses combinatorial geometry based on macro bodies, e.g. boxes, cylinders, hexagons, spheres, cones, etc., and surfaces. The SERPENT model is based on the STereo Lithographic (STL) geometry representation that is used by 3D printers. The STL geometry was constructed using the CUBIT computer program. The water cooling system of the stationary and the rotating reflectors has a very complicated geometry, involving serpentines and irregular surfaces profiles. The materials in these areas have been homogenized using the GIMP image editor according to the material distributions obtained from the colors of the design drawings. The MCNP and the SERPENT inputs consist of ~1500 and ~1750 lines, respectively. The calculated effective multiplication factors from these two Monte Carlo computer programs with different models agree within 50 pcm.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

CdS quantum dots/Ti3+-TiO2 nanobelts heterojunctions as efficient visible-light-driven photocatalysts

Highlights: • A novel CdS QDs/Ti{sup 3+}-TiO{sub 2} nanobelts heterojunction photocatalyst is prepared. • It narrows the bandgap and extends the photoresponse to visible light region. • It exhibits excellent visible-light-driven photocatalytic performance. • It is due to synergistic effect of CdS QDs, Ti{sup 3+} self-doping and heterojunction. - Abstract: CdS quantum dots (QDs)/Ti{sup 3+}-TiO{sub 2} nanobelts heterojunctions as 0D/1D architectures are fabricated through hydrothermal-chemical bath deposition combine with in-situ solid-state chemical reduction approach. The CdS QDs of ∼7 nm are loaded on TiO{sub 2} nanobelts with width of 50–300 nm and several micrometers long, and the heterojunctions are formed efficiently. The prepared heterojunctions exhibit excellent photocatalytic performance for complete removal of methylene blue (∼99%) and hydrogen production efficiency (∼480.6 μmol h{sup −1}) under visible light irradiation, which are as high as 2 and 23 times than that of pristine TiO{sub 2} nanobelts. The enhancement is attributed to the Ti{sup 3+} self-doping and CdS QDs extend the photoresponse to visible light region and the formation of heterojunctions favor the spatial separation of photogenerated charge carriers. Therefore, the high-efficient 0D/1D heterojunction composites have potential applications in the field of environment and energy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ti3+-TiO2/Ce3+-CeO2 Nanosheet heterojunctions as efficient visible-light-driven photocatalysts

Highlights: • A novel Ti{sup 3+}-TiO{sub 2}/Ce{sup 3+}-CeO{sub 2} nanosheet heterojunction is fabricated. • It owns the bandgap of 2.6 eV and extends the photoresponse to visible light region. • It exhibits excellent visible-light-driven photocatalytic performance. • It is due to synergy of Ti{sup 3+}, Ce{sup 3+} co-doping and nanosheet heterojunction. - Abstract: Novel Ti{sup 3+}-TiO{sub 2}/Ce{sup 3+}-CeO{sub 2} nanosheet heterojunctions are successfully prepared via a facile hydrothermal approach combined with a wet-chemical deposition precipitation and an in situ solid-state chemical reduction strategy. The structures of the as-prepared samples are characterized in detail by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy and UV–vis diffuse reflectance spectroscopy. The results show that Ti{sup 3+} and Ce{sup 3+} are both doped into the lattice of TiO{sub 2} and CeO{sub 2}, respectively, which narrow the band gap to 2.7 eV and extend the photoresponse to visible light region. The photocatalytic degradation rate of methyl orange and methylene blue are as high as 93.3% and 97.1% under visible-light illumination, respectively. The high degradation rate is attributed to the efficient doping of Ti{sup 3+} and Ce{sup 3+}, formation of surface oxygen vacancy and heterojunction, which favors the absorption of visible light and separation of photogenerated charge carriers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Accelerator-Driven Subcritical System for Disposing of the U.S. Spent Nuclear Fuel Inventory

The current United States inventory of the spent nuclear fuel (SNF) is ~80,000 metric tons of heavy metal (MTHM), including ~131 tons of minor actinides (MAs) and ~669 tons of plutonium. This study describes a conceptual design of an accelerator-driven subcritical (ADS) system for disposing of this SNF inventory by utilizing the 131 tons of MAs inventory and a fraction of the plutonium inventory for energy production, and transmuting some long-lived fission products. An ADS system with a homogeneous subcritical fission blanket was first examined. A spallation neutron source is used to drive the blanket and it is produced from the interaction of a 1-GeV proton beam with a lead-bismuth eutectic (LBE) target. The blanket has a liquid mobile fuel using LBE as the fuel carrier. The fuel materials are dissolved, mixed, or suspended in the liquid fuel carrier. Monte Carlo analyses were performed to determine the overall parameters of the concept. Steady-state Monte Carlo simulations were performed for three similar fission blankets. Except for, the loaded amount of actinide materials in the LBE is either 5, 7, or 10% of the total volume of the blanket, respectively. The neutron multiplication factors of the three blankets are ~0.98 and the initial MAs blanket inventories are ~10 tons. In addition, Monte Carlo burnup simulations using the MCB5 code were performed to analyze the performance of the three conceptual ADS systems. During operation, fresh fuel was fed into the fission blanket to adjust its reactivity and to control the system power. The burnup analysis shows that the three ADS concepts consume about 1.2 tons of actinides per full power year and produce 3 GW thermal power, with a proton beam power of 25 MW. For the blankets with 5, 7, or 10% actinide fuel particles loaded in the LBE, assuming that the ADS systems can be operated for 35 full-power years, the total MA materials consumed in the three ADS systems are about 30.6, 35.3, and 37.2 tons, respectively. Thus, the corresponding numbers of ADS systems to utilize the 131 tons of MA materials of the SNF inventory are 4.3, 3.7, or 3.5, respectively. ADS concepts with tube bundles inserted in the fission blanket were analyzed to overcome the disadvantages of the homogeneous blanket concept. The liquid lead is used as the target material, the mobile fuel carrier, and the primary coolant to avoid the polonium production from bismuth. Reactor physics and thermal-hydraulic analyses were coupled to determine the parameters of the heterogeneous fission blanket. The engineering requirements for a satisfactory operation performance of the HT-9 ferritic steel structure material have been realized. Two heterogeneous concepts of the subcritical fission blanket with the liquid lead mobile fuel inside or outside the tube bundles were considered. The heterogeneous configuration with the mobile fuel inside the tubes showed better performance than the configuration with mobile fuel outside the bundle tubes. The Monte Carlo burnup codes, MCB5 and SERPENT were both used to simulate the fuel burnup in the ADS concepts with the mobile fuels inside the tubes. The burnup analyses were carried out for 35 full power years. The results show that 5 ADS systems can dispose of the total United States inventory of the spent nuclear fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Enhanced photocatalytic activities of TiO2-reduced graphene oxide nanocomposites controlled by TiOC interfacial chemical bond

Highlights: • A series TiO{sub 2}-reduced graphene oxide (RG) nanocomposites were prepared by hydrothermal methods at different temperature. • The photocatalytic performance of TiO{sub 2}-RG was illustrated by a TiOC interfacial chemical bond. • The photocatalytic properties were investigated by UV–vis test and degrading Rhodamine B. • The results revealed that the nanocomposites obtained at 120 °C possessed the optimum photocatalytic performance. - Abstract: In this study, a hydrothermal-prepared TiO{sub 2}-RG nanocomposites series exhibited excellent photocatalytic activities, of which the results can be largely influenced by a TiOC interfacial chemical bond between TiO{sub 2} nanoparticles and RG nanosheets. A stirring TiO{sub 2}-RG sample was prepared as contrast analysis using the same wet process except for heating. The characteristics of the composites were tested by X-ray diffraction (XRD), Raman, FT-IR, Differential scanning calorimetry (DSC), Thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS) analysis. The photocatalytic properties were verified by UV–vis diffuse reflectance spectra (DRS) testing as well as degrading Rhodamine B (RhB). Our research results show that the better TiOC interfacial chemical bond was formed, the narrower band gap of the nanocomposite was then obtained. The best hydrothermal synthesizing temperature was found out as 120 °C. The TiO{sub 2}-RG nanocomposite, as inexpensive, nontoxic and highly photo-catalytically active, may let it have a potential use in various photocatalytic applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Anomalous vibrational modes in few layer WTe 2 revealed by polarized Raman scattering and first-principles calculations

When layered transition-metal dichalcogenides (TMDs) are scaled down from a three- to a two-dimensional geometry, electronic and structural transitions occur, leading to the emergence of properties not usually found in the bulk. Here, we report a systematic Raman study of exfoliated semi-metallic WTe 2 flakes with thickness ranging from few layers down to a single layer. A dramatic change in the Raman spectra occurs between the monolayer and few-layer WTe 2 as a vibrational mode centered at ~86.9 cm -1 in the monolayer splits into two active modes at 82.9 and 89.6 cm -1 in the bilayer. Davydov splitting of these two modes is found in the bilayer, as further evidenced by polarized Raman measurements. Strong angular dependence of Raman modes on the WTe 2 film thickness reflects that the existence of directional interlayer interaction, rather than isotropic van der Waals (vdw) coupling, is playing an essential role affecting the phonon modes, especially in anisotropic 2D WTe 2 material. Therefore, the strong evolution of Raman modes with thickness and polarization direction, can not only be a reliable fingerprint for the determination of the thickness and the crystallographic orientation, but can also be an ideal probe for such strong and directional interlayer interaction.

36 MATERIALS SCIENCE↗

Plant model of KIPT neutron source facility simulator

Argonne National Laboratory (ANL) of the United States and Kharkov Institute of Physics and Technology (KIPT) of Ukraine are collaborating on constructing a neutron source facility at KIPT, Kharkov, Ukraine. The facility has 100-kW electron beam driving a subcritical assembly (SCA). The electron beam interacts with a natural uranium target or a tungsten target to generate neutrons, and deposits its power in the target zone. The total fission power generated in SCA is about 300 kW. Two primary cooling loops are designed to remove 100-kW and 300-kW from the target zone and the SCA, respectively. A secondary cooling system is coupled with the primary cooling system to dispose of the generated heat outside the facility buildings to the atmosphere. In addition, the electron accelerator has a low efficiency for generating the electron beam, which uses another secondary cooling loop to remove the generated heat from the accelerator primary cooling loop. One of the main functions the KIPT neutron source facility is to train young nuclear specialists; therefore, ANL has developed the KIPT Neutron Source Facility Simulator for this function. In this simulator, a Plant Control System and a Plant Protection System were developed to perform proper control and to provide automatic protection against unsafe and improper operation of the facility during the steady-state and the transient states using a facility plant model. This report focuses on describing the physics of the plant model and provides several test cases to demonstrate its capabilities. The plant facility model uses the PYTHON script language. It is consistent with the computer language of the plant control system. It is easy to integrate with the simulator without an additional interface, and it is able to simulate the transients of the cooling systems with system control variables changing on real-time.

43 PARTICLE ACCELERATORS↗

Measuring and monitoring KIPT Neutron Source Facility Reactivity

Argonne National Laboratory (ANL) of USA and Kharkov Institute of Physics and Technology (KIPT) of Ukraine have been collaborating on developing and constructing a neutron source facility at Kharkov, Ukraine. The facility consists of an accelerator-driven subcritical system. The accelerator has a 100 kW electron beam using 100 MeV electrons. The subcritical assembly has k eff less than 0.98. To ensure the safe operation of this neutron source facility, the reactivity of the subcritical core has to be accurately determined and continuously monitored. A technique which combines the area-ratio method and the flux-to-current ratio method is purposed to determine the reactivity of the KIPT subcritical assembly at various conditions. In particular, the area-ratio method can determine the absolute reactivity of the subcritical assembly in units of dollars by performing pulsed-neutron experiments. It provides reference reactivities for the flux-to-current ratio method to track and monitor the reactivity deviations from the reference state while the facility is at other operation modes. Monte Carlo simulations are performed to simulate both methods using the numerical model of the KIPT subcritical assembly. It is found that the reactivities obtained from both the area-ratio method and the flux-to-current ratio method are spatially dependent on the neutron detector locations and types. Numerical simulations also suggest optimal neutron detector locations to minimize the spatial effects in the flux-to-current ratio method. The spatial correction factors are calculated using Monte Carlo methods for both measuring methods at the selected neutron detector locations. Monte Carlo simulations are also performed to verify the accuracy of the flux-to-current ratio method in monitoring the reactivity swing during a fuel burnup cycle.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Feasibility Studies on Process Coupling of Transesterification and Methanol Synthesis Using Cellulose and Bio-oil

The Sponsored Programs of WKU is the compliance management for the entire campus. They are responsible for both the fiscal compliance, in addition to the coordination and implementation of pre and post-award documentation. Dr. Wei-Ping Pan is the Principal Investigator of the project, and is responsible for the carrying out of the objectives outlined in this proposal. Dr. Yan Cao, serve as the Co-Principal Investigator, who is responsible for directing the team in carrying out the objectives outlined. This project investigates feasibilities of combining the transesterification bio-diesel production into the traditional methanol production process. In this process, the raw materials for process feedstock will be completely the biomass, include cellulose fractions of biomass and bio-oil fractions of biomass. The process product will be either the bio-diesel or mixed bio-diesel and bio-methanol, which both can be directly fed as the alterative liquid fuel and also has some improvement on fuel handling. Since its capability of the complete utilization of every part of biomass (both cellulose biomass and bio-oils) and capability of the in-site optimization of reaction heat transfer and thermodynamics equilibrium shift and instant separation of process product, the proposed process can better balance several drawbacks of individual process during production of bio-diesel. This is a totally “green” process with almost all aspects of process to embody the characterization of renewable, compatibility and economic.

10 SYNTHETIC FUELS↗