Search NASASearch

Engineering topics

Chamberlain, Neil F.

Publications and source records attributed to Chamberlain, Neil F..

Relay Communications Support to the ExoMars Schiaparelli Lander

The European Space Agency’s ExoMars Trace Gas Orbiter (TGO) arrived at Mars on October 19, 2016, three days after releasing the Schiaparelli Lander on a ballistic trajectory to Meridiani Planum. During the separation event, and subsequently during Schiaparelli’s Entry, Descent, and Landing (EDL), the NASA-provided Electra UHF payload onboard TGO was used to record signals from the Schiaparelli Lander for post-processing on the ground to recover both tracking of the lander’s carrier signal and reconstruction of the lander’s 8 kb/s telemetry. In addition, ESA’s Mars Express orbiter also recorded the Schiaparelli signal, with ground post-processing providing independent tracking of the lander carrier signal, and the Giant Metrewave Radio Telescope near Pune, India was configured to provide real-time detection of the lander carrier signal. While an anomaly in the latter stages of EDL led to loss of the lander, these critical event data sets, and in particular the telemetry reconstruction enabled by the TGO Electra recording, proved essential in enabling detailed diagnosis of the anomaly. And while the loss of the lander during EDL precluded the planned surface relay operations, the preparations for that activity provide important lessons learned for future Mars relay support scenarios.

Edwards, Charles D., Jr.

Single-Layer, All-Metal Patch Antenna Element with Wide Bandwidth

It is known that the impedance at the center of a patch antenna element is a short circuit, implying that a wire or post can be connected from the patch to the groundplane at this point without impacting radiation performance. In principle, this central post can be used to support the patch element, thus eliminating the need for dielectric. In spaceborne applications, this approach is problematic because a patch element supported by a single, thin post is highly susceptible to acoustic loads during launch. The technology reported here uses a large-diameter center post as its supporting structure. The supporting structure allows for the fabrication of a sufficiently rigid antenna element that can survive launch loads. The post may be either hollow or solid, depending on fabrication approach and/or mass constraints. The patch antenna element and support post are envisioned as being fabricated (milled) from a single piece of aluminum or other metal. Alternately, the patch plate and support column can be fabricated separately and then joined using fasteners, adhesive, or welding. Casting and electroforming are also viable techniques for manufacturing the metal patch part(s). The patch structure is then either bonded or fastened to the supporting groundplane. Arrays of patch elements can be fabricated by attaching several structures to a common groundplane/support structure.

Chamberlain, Neil F.

Metal Patch Antenna

Disclosed herein is a patch antenna comprises a planar conductive patch attached to a ground plane by a support member, and a probe connector in electrical communication with the conductive patch arranged to conduct electromagnetic energy to or from the conductive patch, wherein the conductive patch is disposed essentially parallel to the ground plane and is separated from the ground plane by a spacing distance; wherein the support member comprises a plurality of sides disposed about a central axis oriented perpendicular to the conductive patch and the ground plane; wherein the conductive patch is solely supported above the ground plane by the support member; and wherein the support member provides electrical communication between the planer conductive patch and the ground plane.

Chamberlain, Neil F.

UAVSAR Active Electronically Scanned Array

The Uninhabited Airborne Vehicle Synthetic Aperture Radar (UAVSAR) is a pod-based, L-band (1.26 GHz), repeatpass, interferometric, synthetic aperture radar (InSAR) used for Earth science applications. Repeat-pass interferometric radar measurements from an airborne platform require an antenna that can be steered to maintain the same angle with respect to the flight track over a wide range of aircraft yaw angles. In order to be able to collect repeat-pass InSAR data over a wide range of wind conditions, UAVSAR employs an active electronically scanned array (AESA). During data collection, the UAVSAR flight software continuously reads the aircraft attitude state measured by the Embedded GPS/INS system (EGI) and electronically steers the beam so that it remains perpendicular to the flight track throughout the data collection

Sadowy, Gregory, A.

Impulse Testing of Corporate-Fed Patch Array Antennas

This paper discusses a novel method for detecting faults in antenna arrays. The method, termed Impulse Testing, was developed for corporate-fed patch arrays where the element is fed by a probe and is shorted at its center. Impulse Testing was devised to supplement conventional microwave measurements in order to quickly verify antenna integrity. The technique relies on exciting each antenna element in turn with a fast pulse (or impulse) that propagates through the feed network to the output port of the antenna. The resulting impulse response is characteristic of the path through the feed network. Using an oscilloscope, a simple amplitude measurement can be made to detect faults. A circuit model of the antenna elements and feed network was constructed to assess various fault scenarios and determine fault-detection thresholds. The experimental setup and impulse measurements for two patch array antennas are presented. Advantages and limitations of the technique are discussed along with applications to other antenna array topologies

antenna array