Engineering topics

Chouhan, Vijay [Fermilab]

Publications and source records attributed to Chouhan, Vijay [Fermilab].

6 records

DOE OSTI2026

Cryogenic RF characterization of the MAGO cavity for high-frequency gravitational-wave detection

Superconducting radio-frequency (SRF) cavities are promising resonant sensors for gravitational-wave detection in the kHz-MHz frequency range. We report the cryogenic RF characterization of a prototype superconducting niobium cavity with an unconventional geometry designed for narrow electromagnetic mode separation. Following an adapted surface preparation procedure, cryogenic tests were performed at Fermilab and DESY at temperatures down to 2 K. Mechanical tuning at room temperature achieved a mode splitting of approximately 11 kHz at cryogenic temperature. High electromagnetic quality factors consistent with previous prototype cavities were measured. The measurements further revealed phase transfer characteristics relevant for stable low-level RF control as well as indications of mode coupling potentially caused by one-point multipacting. In addition, first cryogenic measurements of the mechanical eigenmodes yielded mechanical quality factors significantly below commonly assumed theoretical values. These results demonstrate the successful application of established SRF preparation and characterization techniques to a non-standard resonator geometry and provide important experimental input for the development of future SRF-based gravitational-wave detectors.

Dokuyucu, Can [DESY]↗

DOE OSTI2025

Understanding Surface Contamination Effects in Mid-T Baked Cavities

Medium-temperature baking is applied to niobium SRF cavities to enhance their quality factor. However, mid-T baking performed in the 300-350 °C range may lead to the formation of surface carbides, which can prevent the cavities from exhibiting the full benefit of mid-T baking. To investigate the effect of potential surface contaminants, the top RF layer of mid-T-baked cavities was removed using an ultralight electropolishing process. The performance of the mid-T baked cavities was significantly improved after applying this ultralight EP. This presentation summarizes the latest results on this study.

Chouhan, Vijay [Fermilab]↗

DOE OSTI2025

Improving the Performance of Mid-T Baked Niobium Cavities through Post-Bake Surface Treatment

he Medium temperature (mid-T) baking of niobium superconducting radio-frequency cavities at 300 350 C in a vacuum furnace is known to enhance the quality factor (Q₀). However, despite this improvement, cavities treated with this process often exhibit premature quench at relatively low accelerating fields. This limitation is suspected to arise from the formation of surface contaminants, such as niobium carbides, during the furnace bake at 350 C for 3 h. To investigate the influence of potential surface contamination, this study applied an ultralight chemical removal to 1.3 GHz and 650 MHz single-cell cavities that had undergone medium-temperature baking. The removal of the top RF surface layer led to a notable improvement in the quench field and Q₀, indicating a beneficial effect of eliminating possible surface residues introduced during the bake.

Chouhan, Vijay [Fermilab]↗

DOE OSTI2025

Centrifugal Barrel Polishing of a 650 MHz Single-Cell Nb Cavity

This work reports the first application of centrifugal barrel polishing (CBP) to a 650 MHz single-cell niobium superconducting radio frequency cavity. The CBP was performed using a newly installed large tumbler designed to accommodate four large-sized 650 MHz multi-cell cavities. The CBP process was applied to smooth the internal surface of the cavity prior to electropolishing. This study describes the CBP procedure and presents surface results following the CBP process.

Chouhan, Vijay [Fermilab]↗

DOE OSTI2025

Performance Enhancement of Medium Temperature Baked Nb SRF Cavity by Surface Contamination Removal

Medium-temperature (mid-T) baking, typically conducted at 300 350 C, enhances the quality factor of niobium (Nb) superconducting radio frequency cavities. However, surface contamination introduced during vacuum furnace baking can limit the cavity performance. To investigate this effect, a 1.3 GHz single-cell Nb cavity underwent mid-T baking, followed by a chemical treatment to remove the surface contaminants. Post-treatment measurements revealed a significant improvement in both the quality factor and the quench field.

Chouhan, Vijay [Fermilab]↗

DOE OSTI2025

Study on Electropolishing of N-Doped Niobium Surfaces and 650 MHz Cavity for High-Gradient Performance

This presentation provides an overview of the latest studies on electropolishing (EP) of nitrogen-doped niobium surfaces and 650 MHz cavities. The first study focuses on optimizing EP parameters to achieve a pit-free surface on N-doped niobium, highlighting the effects of process conditions on surface pitting and suggesting strategies for mitigation. The second study investigates the EP of 650 MHz cavities to achieve high-gradient performance comparable to that of 1.3 GHz niobium SRF cavities. Additionally, an example of a 650 MHz single-cell cavity is presented, demonstrating its record-high gradient achieved through optimized EP conditions.

43 PARTICLE ACCELERATORS↗