Search NASA⌕ Search

Engineering topics

Collins, Benjamin

Publications and source records attributed to Collins, Benjamin.

At least 55 records · Page 3

An Improved Energy Deposition Model in MPACT and Explicit Heat Generation Coupling with CTF

The default energy deposition model in the CASL neutronics code MPACT assumes all fission energy is deposited locally in fuel rods. Furthermore, equilibrium delayed energy release is assumed for both steady-state and transient calculations. These approximations limit the accurate representation of the heat generation distribution in space and its variations over time, which are essential for power distribution and thermal-hydraulic coupling calculations. In this paper, an improved energy deposition model is presented in both the spatial and time domains. Spatially, the energy deposition through fission, neutron capture, and slowing-down reactions are explicitly modeled to account for the heat generation from all regions of a reactor core, and a gamma smearing scheme is developed that utilizes the gamma sources from neutron fission and capture. In the time domain, the delayed energy release is modeled by solving an additional equation of delayed heat emitters, similar to the equation of delayed neutron precursors.To allow the explicit heat generation coupling, the interfaces between MPACT and CTF were updated to transfer separate heat sources for different material regions (fuel, clad, moderator and guide tube). The results show that the distributions of the energy deposition between MPACT and MCNP agree very well for various 2-D assembly and quarter-core problems without TH feedback. The MPACT/CTF coupled calculation for the hot full power quarter-core case exhibited a reduced peak pin power by 2.3% and a reduced peak fuel centerline temperature by 17 K when using the explicit energy deposition and heat transfer. The new model also shows a maximum 100 pcm keff effect on assembly depletion problems and an increased overall energy release by 7% in a PWR reactivity-initiated accident (RIA) problem.

Liu, Yuxuan↗

Development of Molten Salt Reactor Modeling and Simulation Capabilities in VERA

In recent years, the nuclear community has seen a resurgence of interest in molten salt reactors (MSRs). Because of their molten, flowing fuel, MSRs present several new challenges not present in many other reactors, necessitating tightly coupled multiphysics modeling and simulation for accurate analysis. The Virtual Environment for Reactor Applications (VERA) has been developed to provide a high-fidelity multiphysics framework for reactor analysis. Though it was originally developed for light water reactor applications, VERA’s multiphysics capabilities make for a natural extension to MSR analysis. Recent efforts have focused on capturing the effects of moving fuel. A lumped depletion capability has been added that accounts for the moving and mixing of the fuel, as well as time spent outside the active core. A general multi-phase species transport module has also been added to track the movement and evolution of salt constituents as the salt flows through the core and around the primary loop. This paper presents a discussion of the new MSR capabilities in VERA, along with results for the lumped depletion and species transport capabilities for the Molten Salt Reactor Experiment, demonstrating VERA’s effectiveness in multiphysics simulations of MSRs.

Graham, Aaron↗

Source Range Detector Response Modeling using VERA

The CASL reactor simulation package VERA has been adapted to provide high-fidelity simulation capabilities for modeling source range detector response during subcritical reactor configurations. New features include the activation and shuffling of secondary source assemblies, transfer of burned fuel neutron emission data from the ORIGEN depletion solver to the MPACT deterministic neutron transport solver, allowance of user-defined sources in MPACT based on material composition, ability to solve the subcritical source-driven system with neutron multiplication using the MPACT diffusion solver, and transfer of the calculated fission source from MPACT to the continuous energy Monte Carlo solver Shift for final detector response evaluation. These new capabilities were benchmarked against Watts Bar Unit 1 plant operating data and found to be in very good agreement.

Gentry, Cole↗

Inference of Crud Model Parameters from Plant Data

Over the past several years, the Virtual Environment forReactor Analysis, VERA, has provided a novel capability forthe Consortium for Advanced Simulation of Light Water Re-actors (CASL) to modelcrud-induced power shift (CIPS) inreactors operated by the Tennessee Valley Authority (TVA).While this developed capability in VERA is unique, multiplekey parameters in the crud physics have remained unknown.The methodology employed here provides the capability toinfer these key model parameters from measured plant data.Once the model parameters have been determined, a forwardVERA computation is performed and results are comparedto measured flux map data to determine the ecacy of thecalibrated crud model.

Collins, Benjamin↗

Subgrid Treatment of Spacer Grids in the 2D/1D Subplane Approach

Recent efforts have focused on improving the performance of the 2D/1D subplane implementation in MPACT. One of the developments recently added, presented here, focuses on treating spacer grids using a subgrid approach within each subplane, avoiding the extra computation and potentially improving stability issues that can be present by explicitly modeling the spacer grid with a separate MOC plane. From the cases analyzed, it seems that the approach does a sufficient job of maintaining the accuracy of explicitly meshing the spacer grid (<10 pcm and <1% max pin power error) while offering relatively modest performance gains. Overall, the success of the approach with spacer grids opens up possibilities to apply similar approaches to other structural components, particularly those in the axial reflectors to reduce the number of MOC planes and overall computational burden.

Stimpson, Shane G.↗

Extended Summary: Performance Improvements to the 2D/1D Subplane Method in MPACT

Recent work in MPACT, the primary deterministic neutron transport solver in CASL’s VERA, has focused on significantly improving the overall performance of the calculations and many components within the code have been improved. The paper focuses on the most recent development to improve the 2D/1D subplane method in preparation for a production-level capability. The key developments presented here focus on incorporating a multilevel-in-space CMFD solver that also collapses on the subplane bases, a dynamic subplane meshing capability that better preserves accuracy during control rod movements, and overall usability improvements to make using the subplane method seamless. Compared to the current default 2D/1D solver in MPACT, substantial improvements are demonstrated on two progression problems, including a standard quarter core model, where potential savings observed at ~2× in memory and ~5-6× in core-hour requirements.

Stimpson, Shane G.↗

Coupled Deterministic and Monte Carlo Neutronics for Vessel Fluence Calculations

Throughout core life, the reactor vessel is continually bombarded with neutron flux embrittling the vessel and limiting its useful life. As a result, it is imperative to adequately predict how much flux has passed through the vessel during all stages of its life, as a means of ensuring it has adequate ductility to preclude a brittle fracture even under design accident conditions. At present many of these predictions are made either by purely deterministic or purely stochastic means, each offering their own advantages and disadvantages. This paper introduces a coupled method for calculating fluence through the VERA framework, which enables modeling incremental accumulations of fluence while simultaneously accounting for several factors as they evolve through core life. The intention of this method is to simplify the calculation process and provide better resource utilization in obtaining the required accuracy.

Henderson, Shane↗

Performance Improvements to the 2D/1D Subplane Method in MPACT

Recent work in MPACT, the primary deterministic neutron transport solver in CASL’s VERA, has focused on significantly improving the overall performance of the calculations and many components within the code have been improved. The paper focuses on the most recent development to improve the 2D/1D subplane method in preparation for a production-level capability. The key developments presented here focus on incorporating a multilevel-in-space CMFD solver that also collapses on the subplane bases, a dynamic subplane meshing capability that better preserves accuracy during control rod movements, and overall usability improvements to make using the subplane method seamless. Compared to the current default 2D/1D solver in MPACT, substantial improvements are demonstrated on two progression problems, including a standard quarter core model, where potential savings observed at ~2× in memory and ~5-6× in core-hour requirements.

Stimpson, Shane G.↗

NOBLE METAL MASS TRANSPORT MODEL FOR MOLTEN SALT REACTOR ANALYSIS IN VERA-CS

Molten Salt Reactor designs require robust multiphysics modelling capabilities to further the development of this next generation technology. Due to the unique liquid fuel design, traditional reactor physics analysis codes do not capture all of the important physics of these reactors. This work builds upon a general species transport model implemented into the multiphysics core simulator suite VERA-CS, by adding source and sink models for non-soluble fission products, specifically the noble metals. Noble metal fission products are born in the fuel-salt, but do not form stable fluorides, and instead plate out on various surfaces in the reactor fuel loop. A concentration gradient diffusion-convection based mass transfer model is implemented into the general species transport model within CTF-the subchannel thermal hydraulics code in VERA-CS-and verified. Two noble metal decay chains are analyzed, and their steady state bulk and surface concentrations are calculated for a simple flow loop in CTF that is representative of the Oak Ridge National Laboratory Molten Salt Reactor Experiment (MSRE). Non-soluble species 99Mo to 99Tc captures wall plate out of decaying species, and non-soluble 135Te to soluble 135I and gaseous 135Xe captures wall loss of decaying species. Results are compared with MSRE data and the possible multiphysics effects of this phenomena are identified. Future work to enhance the robustness of the physical model and couple it with neutronics to evaluate these effects of Noble Metal mass transport is discussed.

Walker, Samuel↗

Low-order multiphysics coupling techniques for nuclear reactor applications

The accurate modeling and simulation of nuclear reactor designs depends greatly on the ability to couple differing sets of physics together. Current coupling techniques most often use a fixed-point, or Picard, iteration scheme in which each set of physics is solved separately, and the resulting solutions are passed between each solver. In the work presented here, two different coupling techniques are investigated: a Jacobian-Free Newton-Krylov (JFNK) approach and a new methodology called Coarse Mesh Finite Difference Coupling (CMFD-Coupling). In this work, both techniques were applied to the low-order CMFD system of equations. This allows for the multiphysics feedback effects to be captured on the low-order system without having to perform a neutron transport solve. The JFNK and CMFD-Coupling approaches were implemented in the MPACT neutron transport code, which is being developed for the Consortium for Advanced Simulation of Light Water Reactors (CASL). These methods were tested on a wide range of practical reactor physics problems, from a single 3D fuel pin to a massively parallel 3D full core problem. When coupled neutronics-thermal hydraulics problems were investigated with both JFNK and CMFD-Coupling, it was concluded that CMFD-Coupling outperformed JFNK in terms of both accuracy and runtime for every problem. When applied to large full core problems with multiple sources of strong feedback enabled, CMFD-Coupling reduced the overall number of transport sweeps required for convergence.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

CRUD Source Term Assessment and Development for VERA

In pressurized water reactors, corrosion of primary loop materials is an ongoing process, as primary loop components (steam generator, hot leg, cold leg, and core) are constantly exposed to the coolant. As a result of this corrosion, primary loop materials are released into the coolant in the form of aqueous metal ions and particulate oxides. These corrosion products are the source of materials that form crud deposits on fuel rod clad surfaces. The mass of corrosion products available to create crud will limit the rate and extent of crud buildup that occurs. This is commonly referred to as the crud “source term”. The major contribution to the source term mass comes from the steam generator, due to the large surface area exposed to the coolant. Steam generators are not identical; the wetted area exposed to the coolant and the alloy used in the steam generator tubes vary. Different alloys corrode at different rates; Inconel 690 corrodes at approximately one-third of the rate of corrosion of Inconel 600. The mass of corrosion products released from the steam generator also varies by the area exposed to the coolant. The release of these corrosion products depends on the local environmental factors within the primary loop, including temperature, pH, local fluid conditions, electrochemical potential, and thermodynamic solubilities of the species present within this system. As such, each PWR will have a different crud source term based on these plant-specific parameters. In order to accurately model and predict crud growth and issues that arise from the presence of crud (CIPS, CILC), the source of these corrosion product materials must be accurately modeled in a system mass balance. These models should be mechanistic, representative of the underlying physics phenomena, and account for the effects of the plant-specific design and operating parameters, including the alloys used, local temperatures, and fluid flow conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

VERA Infrastructure

The Virtual Environment for Reactor Applications (VERA) Infrastructure provides the infrastructure to build, configure, test, install, and package for release the VERAS suite of codes that is being developed by the Consortium for the Advanced Simulation of Light-water reactors (CASL). It includes the list of codes that can be built within VERA, the location on the configuration-controlled CASL development computer, the version number used in any particular software installation, the location of the third-party libraries used for testing VERA on a suite of the CASL testing and development computers, and the scripts to configure, build, test, install, and package for release a particular version of VERA. The VERA Infrastructure contains a list of scripts, configuration options, and utilities that are specific to CASL, but contain no physics or numeric, nuclear technology, or encryption technology.

Baird, Mark↗

Calibration of MAMBA and CRUD Sources Using Full-Core CTF+MAMBA

This report outlines a process for the deterministic calibration of MAMBA using the computational toolkit Dakota. The tools and processes for deterministic calibration have been built and are laid out in this report. While completing this milestone, issues emerged with MAMBA that resulted in delays. The consequences for these difficulties to the calibration process are briefly discussed. The report concludes with an outline of a path forward for Bayesian calibration. The Bayesian calibration will be performed next year. This process was laid out by Benjamin Collins, Robert Salko, and Adam Hetzler.

42 ENGINEERING↗

Development of Preliminary VERA-CS Crud Induced Localized Corrosion Modeling Capability

The Consortium for Advanced Simulation of Light Water Reactors (CASL) is developing multiphysics core-simulator software for light water reactors (LWRs) known as VERA-CS in order to improve the state of the art in modeling and simulation of challenge problems that are limiting to the nuclear industry. One of these challenge problems includes fuel rod crud deposition, which can lead to crud-induced power shift (CIPS) and crud-induced localized corrosion (CILC). This paper documents work that was performed to develop a preliminary CILC-modeling capability in VERA-CS in support of the crud challenge problem. The CILC capabilities were developed by coupling VERA-CS to the CASL-developed Cicada code, which provides 1D and 3D clad conduction and oxide growth modeling tools, as well as coupling to the CASL-developed MAMBA code, which is used for modeling clad crud deposition. An approach called rod thermal-hydraulic reconstruction (ROTHCON) was developed and integrated into VERA-CS. This allows the modeler to capture spacer-grid turbulence and heat transfer effects in the CTF subchannel code so that the spatial resolution of crud and oxide rod surface growth could be better resolved. After implementing these capabilities, several assessments were performed to ensure that the capabilities function as expected, and a pin-resolved quarter-core simulation was run as a demonstration.

Salko Jr, Robert↗