Engineering topics

Conroy, B. L.

Publications and source records attributed to Conroy, B. L..

11 records

NASA NTRS1992

A beamwaveguide design for high-power applications

A beam waveguide (BWG) design suitable for high-power applications is described. The design features a transmit-only, four-port high-gain horn as input to a BWG system with a single parabolic mirror and three flat plates. The use of a single parabolic mirror is such that the highest field concentration is no greater than that caused by the horn itself. The horn is linearly polarized and a grid reflector is used to reflect the orthogonal polarization into the receive feed. A rotatable dual polarizer provides for arbitrary transmit polarization. The dual-reflector system is shaped to provide uniform illumination over the main reflector and therefore maximum gain for the given size aperture. Measured data from a scale model BWG system are presented.

Imbriale, W. A.↗

NASA NTRS1990

Conceptual design of a 1-MW CW X-band transmitter for planetary radar

A proposed conceptual design to increase the output power of an existing X-band planetary radar transmitter used for planetary radar exploration from 365 kW to 1 MW CW is presented. The basic transmitter system requirements as dictated by the specifications for the radar are covered. The characteristics and expected performance of the high-power klystrons are considered, and the transmitter power amplifier system is discussed. Also included is the design of all of the associated high-power microwave components, the feed system, and the phase-stable exciter. The expected performance of the beam supply, heat exchanger, and monitor and control devices is also presented. Finally, an assessment of the state-of-the-art technology needed to meet system requirements is given and possible areas of difficulty are summarized.

Bhanji, A. M.↗

NASA NTRS1988

Conceptual design of a 1-MW CW X-band transmitter for planetary radar

A proposed conceptual design to increase the output power of an existing X-band radar transmitter used for planetary radar exploration from 365 kW to 1 MW CW is presented. The basic transmitter system requirements as dictated by the specifications for the radar are covered. The characteristics and expected performance of the high-power klystrons are considered, and the transmitter power amplifier system is described. Also included is the design of all of the associated high-power microwave components, the feed system, and the phase-stable exciter. The expected performance of the beam supply, heat exchanger, and monitor and control devices is also presented. Finally, an assessment of the state-of-the-art technology needed to meet system requirements is given and possible areas of difficulty are summarized.

Bhanji, A. M.↗

NASA NTRS1988

Transmitter data collection using Ada

A data collection system installed on the 400 kilowatt X-band transmitter of the Goldstone Solar System Radar is described. The data collection system is built around the off-the-shelf IEEE 488 instrumentation, linked with fiber optics, controlled by an inexpensive computer, and uses software written in the Ada language. The speed and accuracy of the system is discussed, along with programming techniques used for both data collection and reduction.

Conroy, B. L.↗

NASA NTRS1987

Thermal evaluation method for Klystron RF power

The feasibility of adding instrumentation to the cooling system of a microwave transmitter for use as a calorimetric power measurement calibration is examined. It considers the accuracy of the basic measurements as well as heat sources and losses not measured. Experimental results are presented in support of the theory.

Conroy, B. L.↗

NASA NTRS1986

Ultrasonic Bonding to Metalized Plastic

New technique makes it possible to bond wires ultrasonically to conductor patterns on such soft substrates as plain or ceramic-filled polytetrafluoroethylene. With ultrasonic bonding, unpackaged chips attached to soft circuit boards. Preferred because chips require substrate area and better matched electrically to circuit board at high frequencies.

Conroy, B. L.↗

NASA NTRS1986

Microwave Power Combiner With Switching Diodes

In multiple-port microwave power combiner, each of outputs of two or more power amplifiers of same frequency and phase passed to common output port separately or together. Each amplifier connected to combiner through switch consisting of resonant structures, radio-frequency chokes, and diode. Switches not only permit flexiblity in selection of amplifiers but isolate unused amplifiers from network, all while operating at relatively low power loss.

Conroy, B. L.↗

NASA NTRS1985

X-Band Strip-Line Power Divider/Combiner

Strip-line circuit for X-band signals both divides and combines microwave power for distributed amplifier. Strip-line pattern (foil pattern over insulating layer over ground plane) laid out so all eight distributed ports lie at electrical distances of odd integral multiples of half wavelength from main input/output port. Strip line used as power divider and as power combiner.

Conroy, B. L.↗

NASA NTRS1981

High-power solid-state microwave transmitter

Transmitter phases outputs from individual amplifier modules then combines them in multielement array feed antenna. Size and power capability of system are variable for radar and small-angle scanning applications.

Boreham, J. D.↗

NASA NTRS1979

Evaluation of the JPL X-band 32 element active array

Tests performed on an X-band 32-element active array are described. Antenna pattern characteristics of the array were tested in its standard operating mode as well as several degraded performance modes, including failures of 1, 2, 3, 4, 8, 16, and 31 elements. Additionally, the array was characterized with the addition of a metallic shroud, and also characterized versus rf drive level and at a single off-axis electronic beamsteered position. Characterization was performed on several of the 3/4-watt, three-stage, X-band solid-state power amplifier modules. The characterization included swept amplitude response, amplitude and phase versus temperature from -20 to +60 C, and intermodulation distortion of selected modules. The array is described and conclusions and recommendations based upon the experience and results achieved are included.

Boreham, J. F.↗

NASA NTRS1975

Automatic solar tracker

Mechanism uses differential pressure of condensable fluid against fixed piston to equalize radiant energy on pair of blackbody elements.

Conroy, B. L.↗