Engineering topics
Publications and source records attributed to Cotlet, Mircea.
Explore the source record for details and available documents.
Formamidinium lead iodide (FAPI) has gained attention for hybrid perovskite solar cell (PSC) applications due to its enhanced stability and narrow bandgap. However, a significant challenge remains in inducing and stabilizing the elusive perovskite “black phase”—photoactive cubic α-FAPI—as the relatively bulky FA + cations tend to favor the thermodynamically stable nonphotoactive “yellow phase”. Here, in this study, we present a templated growth strategy employing thiol-functionalized MoS 2 nanosheets as templates. By introduction of 3-mercaptopropionic acid (MPA)-functionalized MoS 2 as a growth template, precise control over crystal formation was achieved, favoring the growth of high-quality α-FAPI films. These advanced templated films exhibited substantial improvements in charge transport properties, efficient light absorption, and enhanced charge extraction. As a result, the PSCs achieved a significantly enhanced power conversion efficiency (PCE) compared to the nontemplated control device, increasing from 20.6 to 22.5%. The MoS 2 -incorporated device also demonstrated excellent shelf stability, maintaining 91% of the initial PCE even after 1600 h of storage without device encapsulation.
Rational design of chiral two-dimensional hybrid organic–inorganic perovskites is crucial to achieve chiroptoelecronic, spintronic, and ferroelectric applications. Here, in this study, an efficient way to manipulate the chiroptoelectronic activity of 2D lead iodide perovskites is reported by forming mixed chiral (R- or S-methylbenzylammonium (R-MBA + or S-MBA + )) and achiral (n-butylammonium (nBA + )) cations in the organic layer. The strongest and flipped circular dichroism signals are observed in (R/S-MBA 0.5 nBA 0.5 ) 2 PbI 4 films compared to (R/S-MBA) 2 PbI 4 . Moreover, the (R/S-MBA 0.5 nBA 0.5 ) 2 PbI 4 films exhibit pseudo-symmetric, unchanged circularly polarized photoluminescence peak as temperature increases. First-principles calculations reveal that mixed chiral–achiral cations enhance the asymmetric hydrogen-bonding interaction between the organic and inorganic layers, causing more structural distortion, thus, larger spin-polarized band-splitting than pure chiral cations. Temperature-dependent powder X-ray diffraction and pair distribution function structure studies show the compressed intralayer lattice with enlarged interlayer spacing and increased local ordering. Overall, this work demonstrates a new method to tune chiral and chiroptoelectronic properties and reveals their atomic scale structural origins.
Zinc tungstate is a semiconductor known for its favorable photocatalytic, photoluminescence, and scintillation properties, coupled with its relatively low cost, reduced toxicity, and high stability in biological and catalytic environments. In particular, zinc tungstate evinces scintillation properties, namely the ability to emit visible light upon absorption of energetic radiation such as x rays, which has led to applications not only as radiation detectors but also for biomedical applications involving the delivery of optical light to deep tissue, such as photodynamic therapy and optogenetics. Here, we report on the synthesis of zinc tungstate nanorods generated via an optimized but facile method, which allows for synthetic control over the aspect ratio of the as-synthesized anisotropic motifs via rational variation of the solution pH. Additionally, we investigate the effect of aspect ratio on their resulting photoluminescent and radioluminescent properties. We further demonstrate the potential of these zinc tungstate nanorods for biomedical applications, such as photodynamic therapy for cancer treatment, by analyzing their toxicological profile within cell lines and neurons.
Here, the presence of poly- and perfluoroalkyl substances (PFAS) in the environment is associated with adverse health effects but measuring PFAS is challenging due to the associated high cost and technical complexities of the analysis. Here, the reactivity of atomically precise metal-oxo clusters is reported and the foundation for their use is provided as fluorescent nanosensors for PFAS detection. The material comprises crystalline, water soluble, hexanuclear cerium-oxo clusters [Ce 6 (µ 3 -O) 4 (µ 3 -OH) 4 ] 12+ decorated with glycine molecules (Ce-Gly) characterized by fluorescence emission at 353 nm. The Ce-Gly fluorescence is found sensitive to long chain carboxylated PFAS of CF 3 –(CF 2 ) n –, where n ≥ 6, such as perfluorooctanoic, perfluorononanoic and perfluorodecanoic acids. This unique reactivity leads to a change in the emission spectra in a concentration dependent manner, enabling PFAS detection through ligand exchange and aggregation-induced emission (AIE) enhancement. No significant cross-reactivity from potentially co-existing species, including sulfonated PFAS, octanoic and dodecanoic acids, humic acid, and inorganic ions is observed. With an optimal concentration of 3.3 µg mL -1 Ce-Gly, the method demonstrated detection limits of 0.24 ppb for PFOA and 0.4 ppb for PFNA. These findings highlight the potential of fluorescence-based detection strategies utilizing nanoscale probes such as Ce-Gly as fluorescent probes and nanosensors for PFAS.
The polaron is an essential photoexcitation that governs the unique optoelectronic properties of organic–inorganic hybrid halide perovskites, and it has been subject to extensive spectroscopic and theoretical investigation over the past decade. A crucial but underexplored question is how the nature of the photogenerated polarons is impacted by the microscopic perovskite structure and what functional properties this affects. To tackle this question, we chemically tuned the interactions between perovskite quantum dots (QDs) to rationally manipulate the polaron properties. Through a suite of time-resolved spectroscopies, we find that inter-QD interactions open an excited-state channel to form large polaron species, which exhibit enhanced spatial diffusion, slower hot polaron cooling, and a longer intrinsic lifetime. At the same time, polaronic excitons are formed in competition via localized band-edge states, exhibiting strong photoluminescence but are limited by shorter intrinsic lifetimes. Furthermore, this control of polaron type and function through tunable inter-QD interactions not only provides design principles for QD-based materials but also experimentally disentangles polaronic species in hybrid perovskite materials.
2D-on-3D (2D/3D) perovskite heterostructures present a promising strategy to realize efficient and stable photovoltaics. However, their applicability in inverted solar cells is limited due to the quantum confinement of the 2D-layer and solvent incompatibilities that disrupt the underlying 3D layer, hampering electron transport at the 2D/3D interface. Herein, solvent-dependent formation dynamics and structural evolution of 2D/3D heterostructures are investigated via in situ X-ray scattering. In this study, it is revealed that solvent interaction with the 3D surface determines the formation sequence and spatial distribution of quasi-2D phases with n = 2–4. Isopropanol (IPA) reconstructs the perovskite into a PbI 2 -rich surface, forming a strata with smaller n first, followed by a thinner substratum of larger n. In contrast, 2,2,2-Trifluoroethanol (TFE) preserves the 3D surface, promoting the formation of uniformly distributed larger n domains first, and smaller n last. Leveraging these insights, Dion–Jacobson perovskites are used with superior charge transport properties and structural robustness to fabricate 2D/3D heterostructures dominated by n ≥ 3 and engineer a favorable energy landscape for electron tunneling. Inverted solar cells based on 3-Aminomethylpyridine and TFE achieve a champion efficiency of 23.60%, with V oc and FF of 1.19 V and 84.5%, respectively, and superior stabilities with t 94 of 960 h under thermal stress.
Layered hybrid halide perovskites gain chirality via the incorporation of chiral organic cations in the spacer layer. These so-called chiral two-dimensional (2D) halide perovskites have attracted considerable interest recently for chiral optoelectronic, spintronic, and ferroelectric applications. However, the effect of temperature on these materials, especially how the structure changes with temperature and its impact on the chiral optoelectronic properties, remains an open question. Here, we study the effect of temperature change on chiral optoelectronic and structural properties through temperature-dependent circularly polarized photoluminescence (CPPL) microscopy and synchrotron powder X-ray diffraction as well as pair distribution function analysis to elucidate the intrinsic chiral optoelectronic and structural variations for R-, S-, and racemic-methylbenzylamine lead iodide. Here our results show that the temperature-induced band gap changes indicate a strong electron–phonon coupling compared to the thermal-induced lattice expansion in chiral 2D perovskites. From powder diffraction measurements, a monotonic lattice expansion is observed on heating with no structural phase transitions over 90–360 K detected for the three samples studied herein. Locally, a strongly anisotropic and even negative expansion in some components of the instantaneous Pb–I pair-distance distribution is suggestive of coupling between dynamical intralayer distortions and lattice expansion. This work provides insights into the fundamental understanding of the temperature effect on chiral optoelectronic and structural properties of chiral 2D perovskites, which can lead to new chiral materials design strategies for future chiral optoelectronic applications.
Controlling crystallization and grain growth is crucial for realizing highly efficient hybrid perovskite solar cells (PSCs). In this work, enhanced PSC photovoltaic performance and stability by accelerating perovskite crystallization and grain growth via 2D hexagonal boron nitride (hBN) nanosheet additives incorporated into the active perovskite layer are demonstrated. Specifically, in situ X-ray scattering and infrared thermal imaging during the perovskite annealing process revealed the highly thermally conductive hBN nanosheets promoted the phase conversion and grain growth in the perovskite layer by facilitating a more rapid and spatially uniform temperature rise within the perovskite film. Complementary structural, physicochemical, and electrical characterizations further showed that the hBN nanosheets formed a physical barrier at the perovskite grain boundaries and the interfaces with charge transport layers, passivating defects, and retarding ion migration. As a result, the power conversion efficiency of the PSC is improved from 17.4% to 19.8%, along with enhanced device stability, retaining ≈90% of the initial efficiency even after 500 h ambient air storage. Here, the results not only highlight 2D hBN as an effective additive for PSCs but also suggest enhanced thermal transport as one of the pathways for improved PSC performance by 2D material additives in general.
We have synthesized several morphologies and crystal structures of MgWO 4 using a one-pot hydrothermal method, producing not only monoclinic stars and large nanoparticles but also triclinic wool balls and sub-10 nm nanoparticles. Herein we describe the importance of reaction parameters in demonstrating morphology control of as-prepared MgWO 4 . Moreover, we correlate structure and composition with the resulting photoluminescence and radioluminescence properties. Specifically, triclinic-phase samples yielded a photoluminescence emission of 421 nm, whereas monoclinic-phase materials gave rise to an emission maximum of 515 nm. The corresponding radioluminescence data were characterized by a broad emission peak, located at 500 nm for all samples. Annealing the wool balls and sub-10 nm particles to transform the crystal structure from a triclinic to a monoclinic phase yielded a radioluminescence (RL) emission signal that was two orders of magnitude greater than that of their unannealed counterparts. Finally, to confirm the practical utility of these materials for biomedical applications, a series of sub-10 nm particles, including as-prepared and annealed samples, were functionalized with biocompatible PEG molecules, and subsequently were found to be readily taken up by various cell lines as well as primary cultured hippocampal neurons with low levels of toxicity, thereby highlighting for the first time the potential of this particular class of metal oxides as viable and readily generated platforms for a range of biomedical applications.
High conductivity, carrier mobility as well as long diffusion length are critical for highly efficient solar cells. Here, we report new types of crystalline inorganic-organic hybrid semiconductors, 2D-Cu 2 I 2 (L) [L = benzo[c][1,2,5]thiadiazole (bs) and benzo[c][1,2,5] selenadiazole (bse)], composed of one-dimensional (1D) copper iodide staircase-like chain and benzodiazole-based ligands. These compounds possess narrow and tunable band gaps and high conductivity. High-quality large single crystals of 2D-Cu 2 I 2 (bse) were grown and used to evaluate the charge transport properties of the material. State-of-the-art time-resolved microwave conductivity (TRMC) techniques were used to investigate the charge carrier dynamics, from which a high conductivity of 2 × 10 -4 S/cm, a carrier mobility of ~1 cm 2 V -1 s -1 , a maximum doping/carrier density of 2 +/- 1 × 10 15 cm -3 , and a diffusion length of ~0.17 um were obtained. We report the excellent water/chemical stability combined with high conductivity makes this I-VII-based hybrid material family promising candidates for potential optoelectronic applications.
Quasi-two-dimensional (2D) organic-inorganic hybrid tin perovskites have emerged as promising alternatives to lead-based perovskites in thin-film photovoltaics because of their reduced toxicity and improved stability. However, the undesired small n-value 2D phases and disordered crystal orientation enormously restrict the efficiency of quasi-2D tin perovskite solar cells (PSCs) due to uncontrollable nucleation and crystal growth processes. Here, we propose a mixed pseudo-halide anion engineering approach by using acetate (Ac - ) and tetrafluoroborate (BF 4 - ) anions to make quasi-2D Ruddlesden-Popper perovskites with a target formula of PEA 2 FA 4 Sn 5 I 16 . We find that the mixed Ac - and BF 4 - anions can not only promote homogeneously distributed PEA + cations in the precursor by effectively breaking the PEA + ···PEA + stacking but also retard the crystallization process by coordinating with unbonded SnI 2 , thereby, significantly reducing small n-value 2D phases, improving the crystal orientation, and suppressing the Sn 2+ oxidation. The resulting PSC exhibits up to 9% power conversion efficiency and 400 h stability.
Plasmonic perovskite solar cells (PSCs) using core-shell type plasmonic particles are designed, which possess the plasmon resonance in the near-infrared range. This can selectively strengthen the interaction of the perovskite layer with low-energy photons. The mesoporous PSCs employing the plasmonic particles have delivered a 10%-15% enhancement of external quantum efficiency in the plasmonic resonance range. This surface-plasmonic effect has been analyzed using complementary techniques, including selective wavelength excitation and time-dependent photoluminescence. Here it is shown that the metal-based core-shell-type plasmonic structures in PSCs optimize the scattering and absorption of incident light and the dynamics of photogenerated carriers. Furthermore, both optical and electronic effects increase the power conversion efficiency of PSCs from 17.49% to 19.88%, paving a way toward controlling the thickness of the photoactive layer for advanced devices such as tandem solar cells.
Perovskite quantum dot (QD) has emerged as a promising material for photovoltaics with its superior stability compared to their three-dimensional bulk counterparts, owing to its thermodynamically stabilized photoactive phase. However, ligand management on perovskite QD surfaces is extremely difficult due to the ionic nature of the perovskite lattice, which often leads to either incomplete removal of the native insulating ligands or formation of trap states during the ligand-exchange process, greatly hampering the photovoltaic performances. In this work, we report an ion-assisted ligand-exchange method for FAPbI 3 QDs using AOAc (A = formamidinium (FA + ), guanidinium (GA + ), and phenethylammonium (PEA + ), OAc = acetate), with the A + and OAC - ions promoting the removal of native long-chain insulating ligands. Further, the more complete ligand exchange results in dense and well-oriented packing of QDs, together with the enhancement of electronic coupling and charge transport across QDs. In addition, the A + and OAC - ions can fill the surface A-/X-site vacancies, respectively, reducing the QD surface trap state density and hence suppressing charge recombination and iodide migration. The p-i-n inverted QD solar cells fabricated with this ligand-exchange method exhibit significant enhancement in shortcircuit current density (J SC ), reaching a PCE of 10.13%. Moreover, unencapsulated devices show impressive stabilities of more than 7300 h (10 months) storage time in a N 2 -filled glovebox.
2D Ruddlesden-Popper perovskites have risen to prominence as stable and efficient photovoltaic materials because of their structural diversity, rich photophysics, and low moisture ingression. However, thin films processed from stoichiometric precursor solutions possess a broad phase distribution of different number of inorganic layers with random crystal orientation, crippling device performance. The effect of methylammonium chloride (MACI) and 3-amino4-phenolsulfonic acid (APSA) on the fabrication of perpendicularly oriented (PEA) 2 MA 4 Pb 5 I 16 films with narrow phase distribution using antisolvent and hot-casting processing techniques is investigated. MACI plays a critical role in suppressing parasitic n ≤ 2 and 3D-like phases. APSA performs the dual function of trap passivation and further narrowing phase polydispersity through strong coordination with Pb 2+ . Ex situ grazing-incident wide-angle X-Ray scattering (GIWAXS) and ultrafast spectroscopic characterization reveal uniformly mixed-phase distribution with disordered orientation in antisolvent treated films, while additive-assisted hot-casting treatment results in oriented, reverse-graded phase distribution, i.e., small-n on the film surface and large-n at the bottom. Arising thin films enable efficient p-i-n solar cells with an efficiency of 14.34%, and a V oc of 1.20 V, retaining 96% initial efficiency after 1440 h under ambient conditions (RH = 50-60%) without encapsulation.
Here the relationship between emission and ligand restriction of a series of ZnSe/ZnS quantum dots (QDs) encapsulated in nanoparticles is investigated systematically via experiments and quantum theory. The QDs have a ZnSe core and a ZnS shell, capped with hydrophobic ligands (triotylphosphine oxide/hexadecylamine), allowing them to be entrapped in a model biomembrane, bicelle, made of zwitterionic dipalmitoyl and dihexanoyl phosphatidylcholines and charged dipalmitoyl phosphatidylglycerol. Enhanced photoluminescence is observed upon encapsulation, depending on the QD-to-lipid ratio. Transmission electron microscopy and small-angle X-ray scattering confirm that QDs are preferably situated at the rim of bicellar discs. A simplified quantum dissipation heat-bath theory is proposed to correlate the enhancement with slower nonradiative processes caused by the restriction-in-motion (RIM) of the surface ligands. However, Fõrster resonance energy transfer due to QD aggregation counteracts the effect.
Perovskite nanocrystals are exceptional candidates for light-emitting diodes (LEDs). However, they are unstable in the solid film and tend to degrade back to the bulk phase, which undermines their potential for LEDs. Here we demonstrate that perovskite nanocrystals stabilized in metal–organic framework (MOF) thin films make bright and stable LEDs. The perovskite nanocrystals in MOF thin films can maintain the photoluminescence and electroluminescence against continuous ultraviolet irradiation, heat and electrical stress. As revealed by optical and X-ray spectroscopy, the strong emission originates from localized carrier recombination. Bright LEDs made from perovskite-MOF nanocrystals are demonstrated with a maximum external quantum efficiency of over 15% and a high brightness of over 10 5 cd m -2 after the device reaches stabilization. During LED operation, the nanocrystals can be well preserved, free of ion migration or crystal merging through protection by the MOF matrix, leading to a stable performance over 50 hours.
Thermal stability of organic–inorganic hybrid perovskites (OIHPs) remains as one of the critical challenges against the stable operation of perovskite solar cells (PSCs) in direct sunlight with elevated temperatures. Here, we show that the addition of a polystyrene-co-polyacrylonitrile (SAN) copolymer can significantly enhance thermal stability of OIHPs and improve the stability of the corresponding PSCs by suppressing the migration of organic cations in OHIP. The methylammonium lead iodide (MAPI) with SAN incorporated within the perovskite layer featured a superior thermal stability compared to pure MAPI without SAN, only displaying an average of 5–15% decrease in PCE even after continuous thermal aging for 24 h at 100 °C. The secondary ion mass spectrometry revealed that the thermal degradation of the pure MAPI was largely associated with MA+ out-migration. Conducting atomic force microscopy analysis further indicated that the incorporated SAN led to a suppression of ionic currents present at the grain boundaries of the perovskite film, which was understood by high immiscibility between SAN and MA+ components as confirmed by the experimentally estimated Flory–Huggins parameter between them. This study newly identifies a potential of using polymer grain encapsulation for enhancing thermal stability of OIHPs and their solar cell performance by suppressing the out-diffusion of cationic organic components.