Search NASA⌕ Search

Engineering topics

Daniel, Claus

Publications and source records attributed to Daniel, Claus.

At least 37 records · Page 2

Influence of Binder Coverage on Interfacial Chemistry of Thin Film LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathodes

In this work, we explore the influence of binder coverage and chemistry on the interfacial properties of the textured Ni-rich cathode LiNi 0.6 Mn 0.2 Co 0.2 O 2 . We find that the formation of the cathode/electrolyte interphase (CEI) composition varies significantly for cathodes coated with either poly(vinylene fluoride) (PVDF), carboxymethyl cellulose (CMC), or lithium polyacrylate (LiPAA) after cycling to high upper cutoff voltages (4.5 V vs Li/Li). The PVDF-coated samples had a thinner CEI and twice the relative concentration of LiF and Li 2 CO 3 to Li x PO y F z species in the CEI compared to the uncoated sample. This correlated with significantly lower interfacial impedance (285 vs ~1700 Ohm-cm 2 ) and improved capacity retention between cycles of the PVDF-coated samples compared to the other binder compositions and the uncoated sample. CMC-coated samples performed worst, with a CEI comprised of greater amounts of Li x PO y F z . In addition, we find the choice of binder results in the selective protection or promotion of electrolyte reactions at the (104) surface of the 622 cathode. This suggests that the choice of binder can impact the surface chemistry and performance of high voltage cathodes and supports an avenue for interest in multifunctional binders for stabilizing the CEI.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration (FY2019 Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, a means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations, though the ink processing, coating and drying processes, to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product.

42 ENGINEERING↗

Structural Degradation of High Voltage Lithium Nickel Manganese Cobalt Oxide (NMC) Cathodes in Solid-State Batteries and Implications for Next Generation Energy Storage

In this study, we report the stability of the layered high voltage cathode NMC622 with respect to a standard liquid electrolyte and in an all solid-state configuration. NMC622 cathodes with a (104) orientation were found to suffer from degradation at high voltage (4.5 V vs Li/Li + ) due to electrolyte-promoted degradation of the layered structure in a carbonate electrolyte. The lithium phosphorus oxynitride (LiPON) electrolyte was able to suppress the extent of this decomposition in solid-state cells but not totally prevent it from occurring. In the solid-state cells the capacity decreased from 203 to 93 mAh/g in the first cycle and from 93 to 79 mAh/g over the subsequent 99 cycles, whereas, after 20 cycles, the liquid cell charge capacity was dominated by the irreversible electrolyte degradation. Furthermore, the interfacial resistances of the solid-state cells were stable with cycling, suggesting minimal degradation of the NMC622/LiPON interface and incumbent losses due to structural evolution associated with cathode orientation. This data indicates that accessing stable high voltage capacity in NMCs will not be enabled by simply stabilizing the cathode–electrolyte interface. Optimizing cathode crystallographic orientation may be the key to accessing this high voltage regime.

25 ENERGY STORAGE↗

Chemical stability and long-term cell performance of low-cobalt, Ni-Rich cathodes prepared by aqueous processing for high-energy Li-Ion batteries

Cobalt content in Li-ion battery cathodes has become a top concern due to its price volatility and limited source availability. Low-cobalt, Ni-rich active materials are promising candidates for next-generation cathodes due to their high capacities, and water-based processing of these materials can further reduce both cost and environmental impact. We systematically evaluated the water compatibility of four different LiNi x Mn 1-x-y Co y O 2 (NMC) powders with increasing nickel contents. Comprehensive characterization verified there is no major change to their bulk structures, and only slight surface modifications related to the removal of contaminant species. For the first time, we demonstrate that LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC 811) cathodes can be formulated in water and cycled 1000 times in full pouch cells with excellent capacity retention (~70% compared to ~76% for NMP-processed cells). When implemented in future battery production lines, aqueous processing of Ni-rich NMC will simultaneously enable cost reductions and higher cell energy densities.

25 ENERGY STORAGE↗

Surface chemistry and composition-induced variation of laser interference-based surface treatment of Al alloys

A key limitation for the use of aluminum alloys in multi-material structural components is effective surface cleaning and texturing techniques to improve the quality of structural joints. In this study, the surface and sub-surface chemistries are investigated for a novel surface treatment method using laser interferometry produced by two beams of a pulsed Nd:YAG laser. Surfaces of AA 5128 aluminum alloy were treated using a two-beam laser interference setup, enabling the structuring of the surface at length scales much less than that of the laser beam. Periodic and patterned surface structures were created by the interference power profile through ablation of deposits and debris and melting and re-solidification of the near-surface region during laser-treatment. Chemical changes to the Al alloy surface induced by laser treatment were examined in detail in this study using both x-ray photoelectron spectroscopy (XPS) and scanning Auger microanalysis (SAM) as a function of number of interfering laser shots. XPS surface analysis indicates that this laser technique is effective at cleaning aluminum surfaces. Furthermore, SAM data indicated that there is a compositional-induced variation of Mg due to laser-interference as Mg-rich areas were found in periodic interference-structured ridges.

36 MATERIALS SCIENCE↗

Method of manufacturing high volumetric density electrodes from self-aligning fiber powders

An electrode and a related method of manufacture are provided. The electrode includes a self-aligning active material having short fiber powders with a cylindrical morphology to increase the packing density from 0.74 to nearly 0.91. The short fiber powders self-align during a slurring coating process as a result of shear forces between a die and a foil. The resulting coating includes parallel short fibers in a closed packed arrangement, providing an increased volumetric capacity of at least approximately 17%.

36 MATERIALS SCIENCE↗

Synthesis of Ni-Rich Thin-Film Cathode as Model System for Lithium Ion Batteries

We demonstrate a process to prepare model electrodes of the Ni-rich layered compound LiNi 0.6 Mn 0.2 Co 0.2 O 2 . These thin-film cathodes are compared with the composite materials to demonstrate the system is a viable platform for isolating interfacial phenomena between the electrolyte and active material without the influence of binders and conductive additives. The appropriate choice of heterolayers was found to influence the preferential orientation of the (101) and (104) planes relative to the (003) plane of the layered R-3m crystal structure, enhancing Li + diffusion and improving electrochemical performance. The addition of a Co interlayer between the Pt current collecting layer and alumina substrate increased the (101) and (104) texturing of the 500 nm Ni-rich film and allowed cells to deliver greater than 50% of their theoretical capacity. This work provides an architecture for isolating complex mechanisms of active materials that suffer from surface reconstruction and degradation in electrochemical cells.

25 ENERGY STORAGE↗

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration - FY2018 Final Report

High-value R2R processing is used to support a wide range of products in applications which span many industrial business sectors. The overall R2R process technology can be considered as “mature” as the process methodology and has been in use for decades. This continuous processing technique traditionally involves deposition of material(s) onto moving webs or carriers or other continuous R2R, belt-fed, or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Current process technologies, which typify “roll to roll”, include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multi-layer technologies can be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, a means must be available to enable manufacture of these products in a cost-competitive manner that is affordable by the general consumer. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches.Within the DOE EERE AMO, it was recognized that establishment of a program supported at the DOE National Laboratories, along with their immense design of materials and equipment modelling capabilities enabled with use of high-performance computing, could take advantage of available R2R infrastructure to manufacture new technologies. In FY 2016, a R2R Consortium was established and provided with initial “seed” funding to take an approach that was envisioned to be supportable by advanced manufacturing R2R processes. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy product development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this collaborative project would leverage the capabilities and expertise at each of four laboratories to further the development of an enabling high-volume cost-competitive platform technology. The collaboration team that is comprised of ORNL, ANL, NREL and LBNL, coordinating with EPB and other selected industry partners, was formed in April 2016 to initially address enhancing battery electrode performance and R2R manufacturing challenges. The research efforts were to predict and measure changes and results in electrode morphology and performance based on process condition changes; to evaluate mixed, active, particle size deposition and drying for novel electrode materials; to model various process condition changes and the resulting morphology and electrode performance; and to develop and validate NDE techniques for in-line measurement of battery electrode material properties. These efforts carried through FY 2017 and completed at the end of FY 2018.The approach was to look at compositions of materials with different particle sizes to make electrode samples using a R2R manufacturing process. The shape, size, and morphology of the materials, the chemistry of the formulation, the nature of slurries, their coating rate, the rate of drying all play a role in determining the final coating architecture, quality, and performance. A commercial cathode material was selected to make a series of cathodes and anodes by single pass, dual pass and slot die methods. Analysis of all the compiled results for this battery electrode development were that the best performing cathodes included: dual-pass electrode with large particles near the foil, mixed small and large particles, and small particles only. Whereas, the best performing anodes were with a mix of small and large graphite particles. An additional core project was added in FY 2017 to conduct studies of fuel cell materials that can be produced using R2R processes. The goal of this project is to explore, understand and optimize material and process parameters to support increased throughput, increased quality, and reduced cost for high volume production of gas-diffusion electrodes (GDEs) for PEMFCs. Project work in FY 2018 were to use a R2R process to fabricate electrodes without ionomer overlayer that can produce the equivalent mass activity as spray-coated electrodes with an ionomer overlayer. Oxygen-limiting current measurements were utilized to optimize oxygen mass transport. Alcohol-rich solvents were investigated, and results were that the alcohol and water ratio can be tuned to control ionomer distribution. Water-rich solvents produce a more dispersed ink which results in better high-current density performance.

36 MATERIALS SCIENCE↗

High temperature materials for heavy duty diesel engines: Historical and future trends

We report that heavy duty (HD) vehicles are projected to be the largest fuel-use subsector in transportation, with current demand for diesel fuel projected to grow 30% by 2040. Historically, a primary strategy for increasing diesel engine efficiency has been to increase peak cylinder pressure (PCP). However, increasing PCP imparts greater mechanical and thermal loads on engine components and materials. In recent years, the material property limits for many components have been reached and further increases in PCP above ~20 MPa have been difficult, while still maintaining the necessary affordability and longevity of on-road HD diesel engines. This paper reviews the historical evolution and major metallurgical advancements of high temperature materials in HD on road diesel engines (10–15 L displacement) up to the current state of the art, focusing on materials in the engine block, cylinder heads, pistons, valves, and exhaust components. These components cover a wide range of material classes, including cast iron, ferritic steel, austenitic steel, titanium alloys, nickel based super-alloys, and high temperature coatings. Finally, the microstructural degradation and failure mechanisms of the materials associated with the complex mechanical and thermal loading during service are discussed and key areas for future materials research are suggested that overcome technical barriers.

36 MATERIALS SCIENCE↗

Laser nanostructured surface preparation for joining materials

A joined article includes a first component having a laser-treated surface portion and a second component having a laser-treated surface portion. An adhesive joins the first component to the second component at the treated surface portion. A method of making a joined article form components and a system for making joined articles are also disclosed.

Sabau, Adrian Stefan↗

Identifying degradation mechanisms in lithium-ion batteries with coating defects at the cathode

Understanding the effect of electrode manufacturing defects on lithium-ion battery (LIB) performance is key to reducing the scrap rate and cost during cell manufacturing. In this regard, it is necessary to quantify the impact of various defects that are generated during the electrode coating process. To this end, we have tested large-format 0.5 Ah LiNi 0.5 Mn 0.3 Co 0.2 O 2 /graphite pouch cells with defects intentionally introduced into the cathode coating. Different types of coating defects were tested including agglomerates, pinholes, and non-uniform coating. Electrodes with larger non-coated surface had greater capacity fade than baseline electrodes, while pinholes and agglomerates did not affect performance adversely. Furthermore, post cycle analysis of electrodes showed that the anode facing the defective region in the cathode was clearly impacted by the defect. Further characterization using Raman spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction provided evidence for a proposed mechanism for material degradation related to the most detrimental type of coating defect.

25 ENERGY STORAGE↗

Three-dimensional conductive network formed by carbon nanotubes in aqueous processed NMC electrode [Three-dimensional conductive network formed by carbon nanotubes in aqueous processed NMC532 electrode]

Aqueous processing of lithium nickel manganese cobalt oxide (LiNi 0.5 Mn 0.3 Co 0.2 O 2 , NMC 532) cathodes was investigated by incorporating carbon nanotubes (CNTs) as the conductive additive. Morphology observation showed CNTs evenly disperse across the electrode, uniformly covering each primary particle, and form three-dimensional electronic pathways. A resistance measurement indicated the CNTs can improve the electronic conductivity of the composite electrode by an order of magnitude compared to carbon black. CNTs based electrodes showed higher rate performance, lower hysteresis, and better cycling performance with 99.4% capacity retention after 200 cycles in full pouch cells compared to 94.6% for carbon black based electrode. Meanwhile, the content of active materials in the electrode was increased from 90 wt% to 96 wt% and the energy density was increased by 11.7%. Furthermore, this research demonstrates an effective combined approach for achieving aqueous processed cathodes with enhanced durability while simultaneously achieving higher energy density by reducing the content of inactive components.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

FY2017 annual report: Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Consortium Project

The following report provides a description of the program structure and technical accomplishments made during FY 2017 to overcome challenges for expanding use of R2R technologies and processing for clean energy applications. Technologies are under development that enable enhanced manufacturing of battery electrodes, fuel cells and water separation membranes that take advantage of advancements in new functional materials. Data mining, visualization, modeling and simulation for the materials, technologies and processes being developed allow for improvements in R2R manufacturing applications. This report documents the research conducted by four DOE national laboratories as a consortium in collaboration with industry partnerships. The research is directly applicable to AMM strategies that apply the National Science and Technology Council’s Materials Genome Initiative (NSTC 2011) approach to enhance the performance of battery, fuel cell and water membrane materials. This effort supports building the foundation of technologies, processes and a U.S. manufacturing base that will enable an order of magnitude in shorter process development cycles with the pathway for initial commercialization within months instead of years.

36 MATERIALS SCIENCE↗

Roll-to-Roll Advanced Materials Manufacturing Lab Consortium

Oak Ridge National Laboratory (ORNL), Argonne National Laboratory (ANL), Lawrence Berkeley National Laboratory (LBNL), and the National Renewable Energy Laboratory (NREL) in collaboration with Eastman Kodak Business Park (Kodak) and Citrine Informatics (Citrine) formed a consortium to broadly disseminate materials, process science, and advanced technologies to industry in the area of R2R manufacturing.

36 MATERIALS SCIENCE↗

Characterization of dielectric materials

A system and a method for characterizing a dielectric material are provided. The system and method generally include applying an excitation signal to electrodes on opposing sides of the dielectric material to evaluate a property of the dielectric material. The method can further include measuring the capacitive impedance across the dielectric material, and determining a variation in the capacitive impedance with respect to either or both of a time domain and a frequency domain. The measured property can include pore size and surface imperfections. The method can still further include modifying a processing parameter as the dielectric material is formed in response to the detected variations in the capacitive impedance, which can correspond to a non-uniformity in the dielectric material.

36 MATERIALS SCIENCE↗