Search NASA⌕ Search

Engineering topics

Daniel, Claus

Publications and source records attributed to Daniel, Claus.

At least 19 records

Dry-processed electrodes enabled by polytetrafluoroethylene fibrillation for high-performance lithium-ion batteries

The dry processing technique of polytetrafluoroethylene (PTFE) fibrillation offers significant advancements in cost reduction, environmental impact, and electrochemical performance. Dry processing alone allows for ∼ 20–60% cost reduction and increases of up to 40 mg cm⁻2 of areal loading – it typically comes at a reduction of rate capability. By leveraging the network structure of fibers, this method enhances rate capability and cycling performance, providing a compelling alternative to the conventional and currently predominant wet processing. The review delves into PTFE fibrillation mechanisms and examines critical influencing factors including material properties and processing parameters. It also discusses challenges associated with the electrodes fabricated by PTFE fibrillation, including structural instability due to insufficient PTFE fibrillization, compromised electrical conductivity from an insufficient conductive network, inhomogeneous dispersion resulting from the absence of solvents, restricted ionic transport due to increased electrode thickness, inadequate adhesion to current collector because of low surface energy of PTFE, electrochemical degradation due to low lowest unoccupied molecular orbital (LUMO) level of PTFE, particle damage during processing and environmental concerns related PTFE being a perfluoroalkyl and polyfluoroalkyl substances (PFAS). Recent research innovations aimed at mitigating these issues, their application in beyond-lithium batteries, and future research directions are thoroughly discussed.

Park, Hyunji↗

Method of solvent-free manufacturing of composite electrodes incorporating radiation curable binders

A method of making an electrode includes the step of mixing active material particles, radiation curable resin precursors, and electrically conductive particles to create an electrode precursor mixture. The electrode precursor mixture is electrostatically sprayed onto a current collector to provide an electrode preform. The electrode preform is heated and calendered to melt the resin precursor such that the resin precursor surrounds the active particles and electrically conductive particles. Radiation is applied to the electrode preform sufficient to cure the radiation curable resin precursors into resin.

Du, Zhijia↗

Advanced Research Directions on AI for Energy

This AI for Energy report further details grand challenges that provide significant opportunities for energy applications across nuclear energy, the power grid, carbon management, energy storage, and energy materials over the next decade. The main conclusions and opportunities from this study are available in the Key Findings section of this report.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Laser nanostructured surface preparation for joining materials

A joined article includes a first component having a laser-treated surface portion and a second component having a laser-treated surface portion. An adhesive joins the first component to the second component at the treated surface portion. A method of making a joined article form components and a system for making joined articles are also disclosed.

Sabau, Adrian Stefan↗

Method of solvent-free manufacturing of composite electrodes incorporating radiation curable binders

A method of making an electrode includes the step of mixing active material particles, radiation curable resin precursors, and electrically conductive particles to create an electrode precursor mixture. The electrode precursor mixture is electrostatically sprayed onto a current collector to provide an electrode preform. The electrode preform is heated and calendered to melt the resin precursor such that the resin precursor surrounds the active particles and electrically conductive particles. Radiation is applied to the electrode preform sufficient to cure the radiation curable resin precursors into resin.

25 ENERGY STORAGE↗

Impact of secondary particle size and two-layer architectures on the high-rate performance of thick electrodes in lithium-ion battery pouch cells

Increasing lithium-ion battery gravimetric energy density to > 300 Wh/kg, while simultaneously meeting a cost target of $80/kWh, is of paramount importance to increasing the driving range and affordability of electric vehicles. One way to address this goal is to reduce inactive components by increasing electrode areal capacities, but conventional thick electrode designs typically perform poorly at high discharge rates due to Li + mass transport limitations. Here we compare the rate capability and cycle life of NMC 532/graphite pouch cells made with five different thick cathode and anode designs paired together in 25 combinations. We find that using different particle sizes to structure both the cathode and anode architectures in two-layer configurations results in a 2X capacity improvement over the worst-performing combination at high discharge rates (97 vs. 46 mAh/g at 2C). These different cathode/anode designs also translate to different cycle life performance, with many cells cycled at C/2 achieving ~80% capacity retention after 1000 cycles, and cells cycled at 2C showing different degrees of capacity fade. Altogether, these results demonstrate that simple, scalable changes in electrode design can significantly improve the performance of thick electrodes for high energy density batteries.

25 ENERGY STORAGE↗

Probing the electrolyte/electrode interface with vibrational sum frequency generation spectroscopy: A review

Over the past decades, Lithium-ion batteries have seen extensive improvements, and as a result are now the primary choice in many applications for their power, energy, and durability. In recent years, battery cost has reduced by orders of magnitude through adoption of new materials and processes. Despite these advances, interfaces in these battery systems are yet to be fully understood. This is seen as a major limitation to further increase cycle life, calendar life, abuse tolerance, and performances. A major obstacle is a lack of comprehensive understanding of the complex dynamic chemical processes occurring at the electrolyte/electrode interface. In this context, vibrational sum frequency generation (vSFG) spectroscopy possesses the unique capability of probing a molecularly thin interfacial layer to obtain molecular-level information through nonlinear optical interaction. Probing the molecular level processes at the interfaces using such a versatile technique would be a game changer in the advancement of current battery research knowledge. This review article summarizes recent vSFG studies on the electrolyte/electrode interface of various electrode materials and nonaqueous electrolytes for LIBs and discusses future research perspectives. Finally, overall, this focused review highlights the advantages and versatility of vSFG that can be used to further advance present-day battery research.

25 ENERGY STORAGE↗

Multifunctional approaches for safe structural batteries

Recent advancements in Li and Li-ion based energy storage resulted in development of novel electrode materials for higher energy density which are finding their applications in transportation. There appears to be a limitation in improvement of specific energy of the system based solely on design of material compositions for multivalent intercalation compounds. In addition, higher energy stored by the system implies need for addressing safety concerns especially when it comes to large automotive battery packs. New approaches for improvement of both energy density and safety of batteries are emerging, where multifunctionality of the materials and/or architectures is utilized. Here, we present a review for such approaches from multifunctional current collectors to design of batteries capable of supporting mechanical loads and thus possessing ability to be used as a structural component.

25 ENERGY STORAGE↗

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration (FY2020 Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R processing include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating, and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, the means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations and the coating and drying processes to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product. To solve the problems associated with these challenges, the R2R Collaboration is executing a research program with outcomes that will ultimately link modeling, processing, metrology and defect detection tools, thereby directly relating the properties of constituent particles and processing conditions to the performance of final devices. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy materials development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this project leverages the capabilities and expertise at each of five National Laboratories to further the development of multilayer technologies that will enable high-volume, cost-competitive platforms. A typical R2R process has three steps: (1) mixing of particles and various constituents in a slurry, (2) coating of the ink/slurry mixture on a substrate, and (3) drying/curing and processing of the coating. Final performance of devices made via R2R processes is dependent on the active materials (e.g., electrochemical particles in battery or fuel cell electrodes) and the device structure that stems from the governing component interactions within the various steps. However, a fundamental understanding of the underlying mechanisms and phenomena is still lacking, which is why industrial-scale R2R process development and manufacturing is still largely empirical in nature. The FY 2019 through FY 2021 program addresses aspects of the following two targets from the AMO Multi-Year Program Plan: (1) Target 8.1 Develop technologies to reduce the cost per manufactured throughput of continuous R2R manufacturing processes. (A) Increasing throughput of R2R processes by 5 times for batteries (to 50 square feet per minute (50 ft 2 /min)) and capacitors and 10 times for printed electronics and the manufacture of other substrates and MEs used in support of these products. (B) Developing resolution capabilities to enable registration and alignment that will detect, align, and co-deposit multiple layers of coatings and print < 1-micron (1 µm) features using continuous process scalable for commercial production. (C) Developing scalable and reliable R2R processes for solution deposition of ultra-thin (<10 nm) films for active and passive materials. (D) Develop in-line multilayer coating technology on thin films with yields greater than 95%. (2) Target 8.2 Develop in-line instrumentation tools that will evaluate the quality of single and multilayer materials in-process. (A) Developing in-line QC technologies and methodologies for real-time identification of defects and expected product properties “in-use/application” during continuous processing at all size-scales with a focus on the “micro” and “nano” scale traces, lines, and devices, i.e., <1 μm at 300 ft./min for R2R processing in air and <10 nm at 20 ft./min for vacuum (B) Developing technologies to increase the measurement frequency of surface rheology without significant cost increases with a goal of a 10-nanometer in-line profilometry at a production rate of 100,000 square millimeters per minute (100,000 mm 2 /min).

42 ENGINEERING↗

Challenges for and Pathways toward Li-Metal-Based All-Solid-State Batteries

Solid-state batteries utilizing Li metal anodes have the potential to enable improved performance (specific energy >500 Wh/kg, energy density >1500 Wh/L), safety, recyclability, and potentially lower cost (<$100/kWh) compared to advanced Li-ion systems.1,2 These improvements are critical for the widespread adoption of electric vehicles (EVs) and trucks and could create a short-haul electric aviation industry.1-3 Expectations for solid-state batteries are high, but there are significant materials and processing challenges to overcome.

25 ENERGY STORAGE↗

Challenges for and Pathways Toward Solid-State Batteries

Solid-state batteries utilizing lithium metal anodes have the potential to enable batteries with a specific energy of >500 Wh/kg and an energy density of >1,500 Wh/L for thousands of cycles. When optimized they will improve the energy efficiency, operating temperature range, sustainability, and safety at a lower cost compared to projections for advanced Li-ion batteries. This improved performance is critical for the widespread adoption of electric vehicles and may enable future applications such as electric aviation. Expectations for solid-state batteries are high, there are significant materials and processing challenges that need to be overcome. Some of these challenges are well known; others are more subtle and are just becoming known. The challenges and their solutions must be clearly identified to realize high-energy solid-state Li metal batteries. In the United States, the U.S. Department of Energy (DOE) funds the majority of energy storage research and development, including solid state battery research. Web of Science publication analysis shows that worldwide DOE is second largest funder. Work on solid state batteries is distributed across different arms of DOE and is coordinated at headquarters to ensure a broad national portfolio for advanced batteries, including lithium batteries and solid-state battery devices. We note that university and national laboratory researchers in the US with a long-standing interest in solid state batteries is a small, integrated community with recognized impact for publications, patents and startup companies. The opportunity for this group to engage for research with international colleagues is growing, fostered by periodic bilateral meetings supported by DOE and by the recent joint US German research program for lithium battery interface studies. These are valuable opportunities to speed solid-state battery development. The ORNL led virtual workshop, overviewed here, confirms the community’s shared vision of the exciting advances, opportunities, and challenges. Further, we are seeing that this workshop has spawned several new informal collaborations and draft proposals. This encourages us to propose future discussion. On May 11, 2020, Oak Ridge National Laboratory (ORNL) hosted a 6-hour, on-line national workshop to discuss recent advances and most the prominent obstacles to realizing solid-state Li metal batteries. The workshop included more than 30+ experts from national laboratories, universities, and companies, all of whom have worked on solid-state batteries for multiple years. The participants shared recent advances, many not yet in print, illustrating that the community has gained significant new insights for solid-state Li battery materials over the last 5 years. In this report, the major outcomes of the workshop are organized to identify the gaps in our scientific knowledge for four core materials science areas: (1) Li metal anodes, (2) the solid electrolyte in contact with Li metal, (3) active cathode materials and solid-state composite cathodes, and (4) solid electrolytes. Illustrative examples and discussions are reported with the more comprehensive issues in the report. Discussion of additional challenges related to processing of solid-state battery materials and to the designs and architectures for mechanically robust, long-lived batteries received less attention due to time constraints. These are good themes for deeper discussion at a follow-on workshop, where a complete list of critical research topics can be identified.

25 ENERGY STORAGE↗

Batch and continuous methods for evaluating the physical and thermal properties of films

Thermal methods and systems are described for the batch and/or continuous monitoring of films and/or membranes and/or electrodes produced in large-scale manufacturing lines. Some of the methods described include providing an energy input into a film, measuring a thermal response of the film, and correlating these to one or more physical properties and/or characteristics of the film.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Research advances on cobalt-free cathodes for Li-ion batteries - The high voltage LiMn 1.5 Ni 0.5 O 4 as an example

LiMn 1.5 Ni 0.5 O 4 is one of the most promising cathode materials for use in either next generation lithium-ion batteries or all solid-state batteries. However, despite the significant Research and Development (R&D) carried out throughout the last two decades the material has not made serious inroads into market. One of the major reasons is the lack of consistency in the reported intrinsic properties and electrochemical performance owing to major controversies in synthesis, crystal structure and bulk and interfacial properties of LiMn 1.5 Ni 0.5 O 4 , notably in contact with electrolytes. This paper is a compelling review providing an assessment on the mainstream R&D dealing with the various crystal structures of LiMn 1.5 Ni 0.5 O 4 and their evolutions observed during synthesis and cycling in correlation with their electrochemical performance. Influence of electrolytes and additives along with modifications through doping and surface treatments are interrelated, and the electronic and ionic transport properties of the ordered and disordered LiMn 1.5 Ni 0.5 O 4 phases are discussed. Overall, this review provides a detailed assessment on LiMn1.5Ni0.5O4 and the underlying mechanisms governing its electrochemical performance broadly providing a focused framework for further advancement towards commercialization.

25 ENERGY STORAGE↗

Evaporation due to infrared heating and natural convection

The results obtained from a drying experiment under infrared heating are compared to those obtained from correlations for the mass transfer coefficients, which are commonly used to obtain evaporation rates for drying applications. It was shown that the mass transfer coefficients evaluated by natural convection correlations are approximately ten times lower than those measured under infrared (IR) exposure. In this work, an attempt to explain this discrepancy, which has been also observed in other studies and explained on the basis of thermal radiation effects, optical properties of NMP are presented and the implications of the IR and near infrared (NIR) spectrum on the thermal radiation effects and ensuing evaporation rates are discussed. The results show that expected raise in the film temperature, which would be due to the thermal radiation effects, cannot be used to describe the measured evaporation rates for this solvent. Therefore, this study provides important evaporation mass flux data, which cannot be predicted using traditional correlations, for the design of IR assisted drying systems used in membrane fabrication.

42 ENGINEERING↗

Manufacturing of thick composite electrode using solvent mixtures

A method of making an electrode includes the step of dispersing an active electrode material and a conductive additive in a solvent to create a mixed dispersion. The solvent has a surface tension less than 40 mN/m and an ozone forming potential of no more than 1.5 lbs. ozone/lb. solvent. A surface of a current collector is treated to raise the surface energy of the surface to at least the surface tension of the solvent or the mixed dispersion. The dispersed active electrode material and conductive additive are deposited on the current collector. The coated surface is heated to remove solvent from the coating.

25 ENERGY STORAGE↗