Search NASA⌕ Search

Engineering topics

Daniel, Claus

Publications and source records attributed to Daniel, Claus.

At least 109 records · Page 6

Investigating phase transformation in the Li1.2Co0.1Mn0.55Ni0.15O2 lithium-ion battery cathode during high-voltage hold (4.5 V) via magnetic, X-ray diffraction and electron microscopy studies

This study is the first that provides evidence of phase transformation in a Li-rich Li1.2Co0.1Mn0.55Ni0.15O2 cathode material for lithium-ion batteries (LIBs) during constant voltage charging. Diffraction and magnetic measurement techniques were successfully implemented to investigate the structural transformation in this cathode material during holding a half-cell at 4.5 V in a charged state. The results from X-ray diffraction showed a decrease in c-lattice parameters during high-voltage hold. Magnetic data revealed an increase in average effective magnetic moments of transition metal (TM) ions at constant voltage corresponding to a change in electronic states of TM ions. Analysis showed the reduction of Ni4+ to Ni2+, which was attributed to charge compensation due to oxygen loss. The appearance of the strong {100} forbidden reflection in the single-crystal selected area electron diffraction (SAED) data was attributed to migration of transition metal ions to the octahedral vacancy sites in the lithium layer during high-voltage hold, which was in agreement with the magnetization results. After prolonged hold at 4.5 V, high-resolution transmission electron microscopy (TEM) images along with SAED results showed the presence of spinel phases in the particles, indicating a layered to spinel like phase transformation at constant voltage in agreement with the magnetic data. The results obtained from these magnetic and diffraction studies furnish the fundamental understanding of the structural transformation pathways in Li-rich cathodes at constant voltage and will be instrumental for modifying the parent structure to achieve greater stability.

Mohanty, Debasish↗

Development and application of processing and process control for nano-composite materials for lithium ion batteries (CRADA Final Report)

Oak Ridge National Laboratory and A123 Systems, Inc. collaborated on this project to develop a better understanding, quality control procedures, and safety testing for A123 System’s nanocomposite separator (NCS) technology which is a cell based patented technology and separator. NCS demonstrated excellent performance. x3450 prismatic cells were shown to survive >8000 cycles (1C/2C rate) at room temperature with greater than 80% capacity retention with only NCS present as an alternative to conventional polyolefin. However, for a successful commercialization, the coating conditions required to provide consistent and reliable product had not been optimized and QC techniques for being able to remove defective material before incorporation into a cell had not been developed. The work outlined in this report addresses these latter two points. First, experiments were conducted to understand temperature profiles during the different drying stages of the NCS coating when applied to both anode and cathode. One of the more interesting discoveries of this study was the observation of the large temperature decrease experienced by the wet coating between the end of the infrared (IR) drying stage and the beginning of the exposure to the convection drying oven. This is not a desirable situation as the temperature gradient could have a deleterious effect on coating quality. Based on this and other experimental data a radiative transfer model was developed for IR heating that also included a mass transfer module for drying. This will prove invaluable for battery coating optimization especially where IR drying is being employed. A stress model was also developed that predicts that under certain drying conditions tensile stresses are formed in the coating which could lead to cracking that is sometimes observed after drying is complete. Prediction of under what conditions these stresses form is vital to improving coating quality. In addition to understanding the drying process other parameters such as slurry quality and equipment optimization were examined. Removal of particles and gels by filtering, control of viscosity by %solids and mixing adjustments, removal of trapped gas in the slurry and modification of coater speed and slot die gap were all found to be important for producing uniform and flaw-free coatings. Second, an in-line Hi-Pot testing method has been developed specifically for NCS that will enable detection of coating flaws that could lead to soft or hard electrical shorts within the cell. In this way flawed material can be rejected before incorporation into the cell thus greatly reducing the amount of scrap that is generated. Improved battery safety is an extremely important benefit of NCS. Evaluation of battery safety is usually accomplished by conducting a variety of tests including nail penetration, hot box, over charge, etc. For these tests entire batteries must be built but the resultant temperature and voltage responses reveal little about the breakdown mechanism. In this report is described a pinch test which is used to evaluate NCS quality at various stages including coated anode and cathode as well as assembled cell. Coupled with post-microscopic examination of the damaged ‘pinch point’ test data can assist in the coating optimization from an improved end-use standpoint. As a result of this work two invention disclosures, one for optimizing drying methodology and the other for an in-line system for flaw detection, have been filed. In addition, 2 papers are being written for submission to peer-reviewed journals.

25 ENERGY STORAGE↗

Visualizing the chemistry and structure dynamics in lithium-ion batteries by in-situ neutron diffraction

We report an in-situ neutron diffraction study of a large format pouch battery cell. The succession of Li-Graphite intercalation phases was fully captured under an 1C charge-discharge condition (i.e., charge to full capacity in 1 hour). However, the lithiation and dilithiation pathways are distinctively different and, unlike in slowing charging experiments with which the Li-Graphite phase diagram was established, no LiC24 phase was found during charge at 1C rate. Approximately 75 mol. % of the graphite converts to LiC6 at full charge, and a lattice dilation as large as 4% was observed during a charge-discharge cycle. Our work demonstrates the potential of in-situ, time and spatially resolved neutron diffraction study of the dynamic chemical and structural changes in “real-world” batteries under realistic cycling conditions, which should provide microscopic insights on degradation and the important role of diffusion kinetics in energy storage materials.

25 ENERGY STORAGE↗

Transformational electrode drying process (Final Report)

This report includes major findings and outlook from the transformational electrode drying project performance period from January 6, 2012 to August 1, 2012. Electrode drying before cell assembly is an operational bottleneck in battery manufacturing due to long drying times and batch processing. Water taken up during shipment and other manufacturing steps needs to be removed before final battery assembly. Conventional vacuum ovens are limited in drying speed due to a temperature threshold needed to avoid damaging polymer components in the composite electrode. Roll to roll operation and alternative treatments can increase the water desorption and removal rate without overheating and damaging other components in the composite electrode, thus considerably reducing drying time and energy use. The objective of this project was the development of an electrode drying procedure, and the demonstration of processes with no decrease in battery performance. The benchmark for all drying data was an 80°C vacuum furnace treatment with a residence time of 18 – 22 hours. This report demonstrates an alternative roll to roll drying process with a 500-fold improvement in drying time down to 2 minutes and consumption of only 30% of the energy compared to vacuum furnace treatment.

25 ENERGY STORAGE↗

Optimization of LiFePO 4 Nanoparticle Suspensions with Polyethyleneimine for Aqueous Processing

Addition of dispersants to aqueous based lithium-ion battery electrode formulations containing LiFePO 4 is critical to obtaining a stable suspension. The resulting colloidal suspensions enable dramatically improved coating deposition when processing electrodes. This research examines the colloidal chemistry modifications based on polyethyleneimine (PEI) addition and dispersion characterization required to produce high quality electrode formulations and coatings for LiFePO 4 active cathode material. The isoelectric point, a key parameter in characterizing colloidal dispersion stability, of LiFePO 4 and super P C45 were determined to be pH = 4.3 and 3.4, respectively. PEI, a cationic surfactant, was found to be an effective dispersant. It is demonstrated that 1.0 wt % and 0.5 wt % PEI were required to stabilize the LiFePO 4 and super P C45 suspension, respectively. LiFePO 4 cathode suspensions with 1.5 wt % PEI demonstrated the best dispersibility of all components, as evidenced by viscosity and agglomerate size of the suspensions and elemental distribution within dry cathodes. In conclusion, the addition of PEI significantly improved the LiFePO 4 performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design of composite polymer electrolytes for Li ion batteries based on mechanical stability criteria

Mechanical properties and conductivity were computed for several composite polymer electrolyte structures. A multi-phase effective medium approach was used to estimate effective conductivity. The Mori-Tanaka approach was applied for calculating the effective stiffness tensor of the composites. An analysis of effective mechanical properties was performed in order to identify the composite structures, which would be capable of blocking the dendrites forming in Li-ion battery when Li metal is used as anode. The data on conductivity, elastic modulus, and Poisson s ratio can be used to formulate design criteria for solid electrolytes that would exhibit appropriate stiffness and compressibility to suppress lithium dendrite growth while maintaining high effective conductivities.

25 ENERGY STORAGE↗

Local detection of activation energy for ionic transport in lithium cobalt oxide

Local activation energy for ionic diffusion is probed on the nanometer level in LiCoO{sub 2} thin films using variable temperature electrochemical strain microscopy (ESM). The high spatial resolution of ESM allows one to extract information about ionic activation energies on the level of individual grains and grain facets, thus bridging the lengths scales of atomistic calculations and traditional macroscopic experiments. A series of control experiments have been performed and possible signal generating mechanisms are discussed to explain the temperature-dependent ESM measurements.

36 MATERIALS SCIENCE↗

In Situ XRD of Thin Film Tin Electrodes for Lithium Ion Batteries

Thin film electrodes for lithium ion batteries (LIB) poses several attractive advantages over traditional composite electrodes including size and shape constraints, operating temperature range, and volumetric energy density. Tin is an attractive candidate for LIB anode applications due to its exceptional specific capacity, cascading voltage profile, safety, wide availability, and low cost. Tin thin film electrodes were sputtered onto the current collector of a recently developed in situ X-ray diffraction (XRD) and were monitored continuously by XRD while cycling. A phase transformation from white tin, to Li2Sn5, to -LiSn, to Li22Sn5 was observed during lithiation with the same phases detected in reverse order during delithiation. Preferred orientation and crystallite size information for these phases was extracted from the XRD data in order to develop a clearer picture of how lithium enters and exits thin film tin electrodes.

in situ↗

Novel cell design for combined in situ acoustic emission and x-ray diffraction study during electrochemical cycling of batteries

An in situ acoustic emission (AE) and x-ray diffraction cell for use in the study of battery electrode materials has been designed and tested. This cell uses commercially available coin cell hardware retrofitted with a metalized polyethylene terephthalate (PET) disk, which acts as both an x-ray window and a current collector. In this manner, the use of beryllium and its associated cost and hazards is avoided. An AE sensor may be affixed to the cell face opposite the PET window in order to monitor degradation effects, such as particle fracture, during cell cycling. Silicon particles, which were previously studied by the AE technique, were tested in this cell as a model material. The performance of these cells compared well with unmodified coin cells, while providing information about structural changes in the active material as the cell is repeatedly charged and discharged.

36 MATERIALS SCIENCE↗

Effective conductivity of particulate polymer composite electrolytes using random resistor network method

The effective DC conductivity of particulate composite electrolytes was obtained by solving electrostatics equations using random resistors network method in three dimensions. The composite structure was considered to consist of three phases: matrix, particulate filler, and conductive shell that surrounded each particle; each phase possessing a different conductivity. Different particle size distributions were generated using Monte Carlo simulations. Unlike effective medium formulations, it was shown that the random resistors network method was able to predict percolation thresholds for the effective composite conductivity. It was found that the mean particle radius has a higher influence on the effective composite conductivity compared to the effect of type of the particle size distributions that were considered. The effect of the shell thickness on the composite conductivity has been investigated. It was found that the conductivity enhancement due to the presence of the conductive shell phase becomes less evident as the shell thickness increases.

36 MATERIALS SCIENCE↗

Evolution of Phase Transformation Behavior in Li(Mn1.5Ni0.5)O4 Cathodes Studies By In Situ XRD

Li(Mn1.5Ni0.5)O4 (MNO) is promising spinel cathode material for lithium ion batteries (LIB) due to its increased intercalation potential and improved capacity retention compared to LiMn2O4. Still, improvements to this materials performance must be achieved before MNO is a viable option for commercial LIB cells. In situ X-ray diffraction of Li(Mn1.5Ni0.5)O4 was performed using a novel electrochemical cell based on coin cell hardware. A diffractogram of the pristine material showed a spinel structure with a Ni2+ oxidation state. As the cell was charged through its 4.75V plateau, a transition between spinels with Ni2+, Ni3+, and Ni4+ oxidation was observed. As the oxidation stage on the nickel increased the lattice parameter of the corresponding spinel was reduced. As discharged ensued the spinel reversed its phases change until only the Ni2+ spinel was present. When discharge reached the 2.75V plateau a tetragonal spinel phase was formed, which upon subsequent cell charging was completely converted back to a cubic spinel phase. Lattice parameter changes of each phase were calculated and showed a characteristic strain release during phase changes. After 15 full cycles the transition between these phases was no longer complete and the formation of the tetragonal spinel phase was no longer detected. A discussion of how these cycle-induced changes to phase transition behavior relate to capacity fade and overall cell performance is presented.

74 ATOMIC AND MOLECULAR PHYSICS↗

Direct mapping of ion diffusion times on LiCoO2 surfaces with nanometer resolution

The strong coupling between the molar volume and mobile ion concentration in ionically-conductive solids is used for spatially-resolved studies of ionic transport on the polycrystalline LiCoO2 surface by time-resolved spectroscopy. Strong variability between ionic transport at the grain boundaries and within the grains is observed, and the relationship between relaxation and hysteresis loop formation is established. The use of the strain measurements allows ionic transport be probed on the nanoscale, and suggests enormous potential for probing ionic materials and devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A study of lithium ion intercalation induced fracture of silicon particles used as anode material in Li-ion battery

The fracture of Si particles due to internal stresses formed during the intercalation of lithium ions was described by means of thermal analogy model and brittle fracture damage parameter. The stresses were calculated following the diffusion equation and equations of elasticity with appropriate volumetric expansion term. The damage parameter takes into account triaxiality of the stress state and change in elasticity upon tension and compression, and represents the probability of fracture under given stress state, - an approach suitable for brittle materials. The results were compared with the acoustic emission data from the experiments on electrochemical cycling of Li ion half-cells with silicon electrodes. A good correlation between experiment and prediction was observed.

74 ATOMIC AND MOLECULAR PHYSICS↗