Search NASA⌕ Search

Engineering topics

De Wolf, Stefaan

Publications and source records attributed to De Wolf, Stefaan.

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Single-source pulsed laser-deposited perovskite solar cells with enhanced performance via bulk and 2D passivation

Single-source vapor deposition of halide perovskites has, to date, remained challenging due to the dissimilar volatilities of the precursors, limiting the controlled transfer of multiple elements at once. Here, we demonstrate that pulsed laser deposition (PLD) addresses the rate-control challenges of single-source evaporation, enabling perovskite solar cells with power conversion efficiencies above 19% after passivation. Combining dry mechanochemical synthesis and PLD, we fabricated (Cl-passivated) MA1−xFAxPbI3 films from a single-source target. These films grow on hole-selective self-assembled monolayers, initially forming a thin PbI2-rich layer, which fully converts to perovskite. An oleylammonium iodide (OAmI) post-treatment is then applied to passivate the perovskite’s top surface by forming a 2D perovskite film. Incorporating PbCl2 in the target and applying OAmI-based 2D passivation results in a remarkable 19.7% efficiency for p-i-n perovskite solar cells with enhanced device stability. This highlights the appeal of PLD to fully unlock the potential of single-source vapor-deposited perovskites.

Soto-Montero, Tatiana↗
DOE OSTI2024

Reverse-Bias Resilience of Monolithic Perovskite/Silicon Tandem Solar Cells

Metal halide perovskites have rapidly enabled a range of high-performance photovoltaic technologies. However, catastrophic failure under reverse voltage bias hinders their commercialization. In this work, we demonstrate that by employing a monolithic perovskite/silicon tandem structure, the perovskite subcell can be effectively protected by the silicon subcell under reverse bias, owing to the low reverse-bias diode current of the silicon subcell. As a result, the tested perovskite/silicon tandem devices show superior reverse-bias resilience compared to perovskite single-junction devices in both long-term reverse voltage biasing tests at the single-cell level and partial shading tests at the module level. These results highlight that, compared to other perovskite technologies, monolithic perovskite/silicon tandems are at a higher technology readiness level in terms of tackling the reverse-bias and partial shading challenge, which is a considerable advantage towards commercialization.

commercialization↗
DOE OSTI2024

Diamine chelates for increased stability in mixed Sn–Pb and all-perovskite tandem solar cells

Perovskite tandem solar cells show promising performance but non-radiative recombination and its progressive worsening with time, especially in the mixed Sn–Pb low-bandgap layer, limit performance and stability. Here, in this study, we find that mixed Sn–Pb perovskite thin films exhibit a compositional gradient, with an excess of Sn on the surface – and we show this gradient exacerbates oxidation and increases the recombination rate. We find that diamines preferentially chelate Sn atoms, removing them from the film surface and achieving a more balanced Sn:Pb stoichiometry, making the surface of the film resistive to the oxidation of Sn. The process forms an electrically resistive low-dimensional barrier layer, passivating defects and reducing interface recombination. Further improving the homogeneity of the barrier layer using 1,2-diaminopropane results in more uniform distribution and passivation. Tandems achieve a power conversion efficiency of 28.8%. As a result, encapsulated tandems retain 90% of initial efficiency following 1000 hours of operating at the maximum power point under simulated one-sun illumination in air without cooling.

14 SOLAR ENERGY↗
DOE OSTI2023

Photovoltaics at multi-terawatt scale: Waiting is not an option

We report a major renewable-energy milestone occurred in 2022: Photovoltaics (PV) exceeded a global installed capacity of 1 TW dc . But despite considerable growth and cost reduction over time, PV is still a small part of global electricity generation (4 to 5% for 2022), and the window is increasingly closing to take action at scale to cut greenhouse gas (GHG) emissions while meeting global energy needs for the future. PV is one of very few options that can be dispatched relatively quickly, but discussions of TW-scale growth at the global level may not be clearly communicating the needed size and speed for renewable-energy installation. A major global risk would be to make poor assumptions or mistakes in modeling and promoting the required PV deployment and industry growth and then realize by 2035 that we were profoundly wrong on the low side and need to ramp up manufacturing and deployment to unrealistic or unsustainable levels.

14 SOLAR ENERGY↗
DOE OSTI2023

Suppressed phase segregation for triple-junction perovskite solar cells

The tunable band gaps and facile fabrication of perovskites make them attractive for multi-junction photovoltaics. However, light-induced phase segregation limits their efficiency and stability: this occurs in wide band gap (> 1.65 eV) I/Br mixed perovskite absorbers, and becomes even more acute in the top cells of triple-junction solar photovoltaics that requires a fully 2.0 eV band gap absorber. We report herein that lattice distortion in I/Br mixed perovskites is correlated with the suppression of phase segregation, generating an increased ion migration energy barrier arising from the decreased average interatomic distance between A-site cation and iodide. Using a ~2.0 eV Rb/Cs mixed-cation inorganic perovskite with large lattice distortion in the top subcell, we fabricated all-perovskite triple-junction solar cells and achieved an efficiency of 24.3% (23.3% certified quasi-steady-state efficiency) with an open-circuit voltage of 3.21 V. This is, to our knowledge, the first reported certified efficiency for perovskite-based triple-junction solar cells. The triple-junction devices retain 80% of their initial efficiency following 420 hours of operation at the maximum power point.

14 SOLAR ENERGY↗
DOE OSTI2022

Regulating surface potential maximizes voltage in all-perovskite tandems

The open circuit voltage (V OC ) deficit in perovskite solar cells (PSCs) is greater in wide bandgap (>1.7 eV) cells than in ~1.5 eV perovskites. Quasi-Fermi level splitting (QFLS) measurements reveal V OC -limiting recombination at the electron transport layer (ETL) contact. This, we find, stems from inhomogeneous surface potential and poor perovskite-ETL energetic alignment. Common monoammonium surface treatments fail to address this; instead we introduce diammonium molecules to modify the perovskite surface states and achieve a more uniform spatial distribution of surface potential. Using 1,3-propane diammonium (PDA), QFLS increases by 90 meV, enabling 1.79 eV PSCs with a certified 1.33 V V OC , and > 19% power conversion efficiency (PCE). Incorporating this layer into a monolithic all-perovskite tandem, we report a record V OC of 2.19 V (89% of the Detailed Balance V OC limit) and > 27% PCE (26.3% certified quasi-steady-state). Furthermore, these tandems retain more than 86% of their initial PCE after 500 hrs operation.

14 SOLAR ENERGY↗
DOE OSTI2022

Photoactivated p-Doping of Organic Interlayer Enables Efficient Perovskite/Silicon Tandem Solar Cells

Solution-processed organic semiconductor layers on rough surfaces tend to vary widely in thickness, significantly hindering charge extraction in relevant optoelectronic devices. Herein, we report the photoactivated p-doping of hole-transporting material (HTM) to enhance hole extraction for (textured) perovskite/silicon tandem solar cells, making the device performance less sensitive to the variation of hole transport layer thickness. We used the ionic compound 4-isopropyl-4'-methyldiphenyliodonium tetrakis(penta-fluorophenyl-borate) (DPI-TPFB) as a p-type dopant in poly(triaryl amine) (PTAA), which we used as the HTM. We observed that light soaking DPI-TPFB-doped PTAA shows approximately 22 times higher conductivity compared with an undoped PTAA film, which translated into an improved fill factor (FF) for tandem solar cells. Our tandem solar cells achieved an ~80% FF and 27.8% efficiency and operated at their maximum power point for 200 h without loss of performance, in addition to retaining ~83% of initial performance over a month of operation in an outdoor environment.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS,S↗
DOE OSTI2020

Polymeric Electron-Selective Contact for Crystalline Silicon Solar Cells with an Efficiency Exceeding 19%

Carrier-selective contacts have become a prominent path forward toward efficient crystalline silicon (c-Si) photovoltaics. Among the proposed contacting materials, organic materials may offer simplified and low-cost processing compared with typical vacuum deposition techniques. In this paper, branched polyethylenimine (b-PEI) is presented as an electron-transport layer (ETL) for c-Si solar cells. The incorporation of a b-PEI interlayer between c-Si(n) and Al leads to a low contact resistivity of 24 mΩ cm 2 . A silicon heterojunction solar cell integrated with b-PEI is demonstrated achieving a power conversion efficiency of 19.4%, which improves the benchmark efficiency of a c-Si solar cell with an organic ETL. This electron selectivity of b-PEI is attributed to its Lewis basicity, i.e., electron-donating ability, promoting favorable band bending at the c-Si surface for electron transport. Moreover, several other Lewis base polymers perform as efficient ETLs in organic/c-Si hybrid devices, indicating Lewis basicity could be a guideline for future organic ETL design.

14 SOLAR ENERGY↗