Search NASA⌕ Search

Engineering topics

Dodge, L. G.

Publications and source records attributed to Dodge, L. G..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Effect of elevated temperature and pressure on sprays from simplex swirl atomizers

An examination is made of the effects of air temperature and pressure on the spray quality of a moderately high capacity pressure swirl atomizer spraying jet-A and No. 2 diesel fuel. Drop size distributions, in terms of both Sauter mean diameter (SMD) and the width of the distribution given by the Rosin-Rammler N parameter, are determined over a variety of air conditions. Close to the nozzle, limited data suggest that the SMDs were a strong function of air density, but independent of air temperature. Trends of SMD and N are shown as a function of distance from the nozzle at all conditions, indicating some of the evaporation characteristics of fuel sprays.

Dodge, L. G.↗
NASA NTRS1986

Performance comparison of Malvern instruments laser diffraction drop size analyzer

The performance of ten laser diffraction particle sizing instruments (Malvern models 2200 and 2600) has been evaluated using a synthetic particle size reference standard in a round-robin test at nine independent laboratories. A calibration reticle consisting of a two-dimensional array of opaque, circular particle images photoetched in chrome thin film deposited on a glass substrate was used as the reference. Mean diameters (e.g., D32) for the reticle measured by the ten unmodified instruments varied by 27 percent. In contrast, data from six instruments with individually calibrated photodetector correction factors demonstrated much better agreement and were within 2.6 percent of the actual reticle properties.

Hirleman, E. D.↗
NASA NTRS1984

Change of calibration of diffraction-based particle sizers in dense sprays

A calibration procedure for diffraction-based particle-sizing instruments using multielement detectors is briefly reviewed. The effects of multiple scattering due to dense sprays on the calibration of these instruments are then examined over a range of sprays with Sauter mean diameters from 20 to 55 microns. An empirical scheme to correct for changes in calibration due to dense sprays or other scattering media is presented.

Dodge, L. G.↗
NASA NTRS1984

Calibration of the Malvern particle sizer

A relatively simple technique has been developed to calibrate particle- and droplet-sizing instruments manufactured by Malvern and other similar Fraunhofer diffraction particle-sizing instruments. Measurements of standard reticles using an instrument calibrated in this manner demonstrate the effectiveness of the procedure. In addition, guidelines are presented to avoid errors due to vignetting of the scattered light signal.

Dodge, L. G.↗
NASA NTRS1984

Development of carbon slurry fuels for transportation (hybrid fuels, phase 2)

Slurry fuels of various forms of solids in diesel fuel are developed and evaluated for their relative potential as fuel for diesel engines. Thirteen test fuels with different solids concentrations are formulated using eight different materials. A variety of properties are examined including ash content, sulfur content, particle size distribution, and rheological properties. Attempts are made to determine the effects of these variations on these fuel properties on injection, atomization, and combustion processes. The slurries are also tested in a single cylinder CLR engine in both direct injection and prechamber configurations. The data includes the normal performance parameters as well as heat release rates and emissions. The slurries perform very much like the baseline fuel. The combustion data indicate that a large fraction (90 percent or more) of the solids are burning in the engine. It appears that the prechamber engine configuration is more tolerant of the slurries than the direct injection configuration.

Ryan, T. W., III↗
NASA NTRS1981

The optical and probe measurement of NO - A comparative study

Measurements were made of NO formation in both subsonic turbulent and nonturbulent media generated from gaseous and liquid fuels. Quartz and metallic, cooled and uncooled probes were employed, and optical measurements were made in the UV with narrow-line and continuum lamps. The extent of systematic error bias in these methods was studied over a wide range of conditions. High resolution measurements were made only on flat flames using a high pressure Xe lamp, while low resolution measurements were done with a hollow cathode lamp on flat flame, swirl burner and jet combustor exhausts. Optical data were reduced using a first principles spectral model and multiple zone treatment of the optical path. No major discrepancies related to processes occurring in probes were identified. Good agreement can be expected in measurements made in subsonic exhaust streams up to 2000 K.

Zabielski, M. F.↗