Search NASA⌕ Search

Engineering topics

Dudley, M

Publications and source records attributed to Dudley, M.

At least 37 records · Page 2

Stacking Faults Created by the Combined Deflection of Threading Dislocations of Burgers Vector c and cplusa during the Physical Vapor Transport Growth of 4H-SiC

Observations have been made, using synchrotron white beam x-ray topography, of stacking faults in 4H-SiC with fault vectors of kind 1/6 <20{bar 2}3>. A mechanism has been postulated for their formation which involves overgrowth by a macrostep of the surface outcrop of a c-axis threading screw dislocation, with two c/2-height surface spiral steps, which has several threading dislocations of Burgers vector c+a, with c-height spiral steps, which protrude onto the terrace in between the c/2-risers. Such overgrowth processes deflect the threading dislocations onto the basal plane, enabling them to exit the crystal and thereby providing a mechanism to lower their densities.

36 MATERIALS SCIENCE↗

Thermal Conductivity and Seebeck Coefficients of Icosahedral Boron Arsenide Films on Silicon Carbide

The thermal conductivity of icosahedral boron arsenide (B{sub 12}As{sub 2}) films grown on (0001) 6H-SiC substrates by chemical vapor deposition was studied by the 3{omega} technique. The room temperature thermal conductivity decreased from 27.0 to 15.3 W/m K as the growth temperature was decreased from 1450 to 1275 C. This is mainly attributed to the differences in the impurity concentration and microstructure, determined from secondary ion mass spectrometry and high resolution transmission electron microscopy, respectively. Callaway's theory was applied to calculate the temperature-dependent thermal conductivity, and the results are in good agreement with the experimental data. Seebeck coefficients were determined as 107 {micro}V/K and 136 {micro}V/K for samples grown at 1350 C with AsH{sub 3}/B{sub 2}H{sub 6} flow ratio equals to 1:1 and 3:5, respectively.

36 MATERIALS SCIENCE↗

Electronic Excitations in B12As2 and their Temperature Dependence by Vacuum Ultraviolet Ellipsometry

The dielectric response function of epitaxial B{sub 12}As{sub 2} films on 4H-SiC was determined at room temperature and at 10 K in the spectral region of 3.6-9.8 eV, i.e., in the vacuum ultraviolet (VUV) spectral region, by synchrotron ellipsometry. The experimental dielectric function was simulated with the critical point parabolic band model. The parameters of the dispersive structures were derived by numerical fitting of the experimental data to the proposed model. New high energy optical transitions are resolved at 5.95, 7.8 and 8.82 eV and their lineshape and origin are discussed. The temperature dependence of the critical point energies and transition strengths was determined, and the excitonic effect is considered.

36 MATERIALS SCIENCE↗

Characterization of 100 mm Diameter 4H-Silicon Carbide CrystalsWith Extremely Low Basal Plane Dislocation Density

Synchrotron White Beam X-ray Topography (SWBXT) studies are presented of basal plane dislocation (BPD) configurations and behavior in a new generation of 100mm diameter, 4H-SiC wafers with extremely low BPD densities (3-4 x 10{sup 2} cm{sup -2}). The conversion of non-screw oriented, glissile BPDs into sessile threading edge dislocations (TEDs) is observed to provide pinning points for the operation of single ended Frank-Read sources. In some regions, once converted TEDs are observed to re-convert back into BPDs in a repetitive process which provides multiple BPD pinning points.

36 MATERIALS SCIENCE↗

Thermal conductivity and Seebeck coefficients of icosahedral boron arsenide films on silicon carbide

The thermal conductivity of icosahedral boron arsenide (B{sub 12}As{sub 2}) films grown on (0001) 6H-SiC substrates by chemical vapor deposition was studied by the 3{omega} technique. The room temperature thermal conductivity decreased from 27.0 to 15.3 W/m K as the growth temperature was decreased from 1450 to 1275 deg. C. This is mainly attributed to the differences in the impurity concentration and microstructure, determined from secondary ion mass spectrometry and high resolution transmission electron microscopy, respectively. Callaway's theory was applied to calculate the temperature-dependent thermal conductivity, and the results are in good agreement with the experimental data. Seebeck coefficients were determined as 107 {mu}V/K and 136 {mu}V/K for samples grown at 1350 deg. C with AsH{sub 3}/B{sub 2}H{sub 6} flow ratio equals to 1:1 and 3:5, respectively.

36 MATERIALS SCIENCE↗

Nucleation Mechanism of 6H-SiC Polytype Inclusions Inside 15R-SiC Crystals

A model is presented for the nucleation mechanism of 6H-SiC polytype inclusions inside 15R-SiC boules. Inhomogeneous densities of screw dislocations lead to uneven growth rates, resulting in complex step overgrowth processes which can partially suppress the Burgers vector of a 15R 1c screw dislocation through the creation of Frank faults and Frank partial dislocations. Combined with stacking shifts induced by the passage of basal plane partial dislocations, it is shown that the partial Burgers vector suppression can leave behind a residual 6H 1c dislocation, which then acts as a nucleus for reproduction of 6H-SiC structure in the 15R-SiC crystal.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Electronic Impact of Inclusions in Diamond

X-ray topography data are compared with photodiode responsivity maps to identify potential candidates for electron trapping in high purity, single crystal diamond. X-ray topography data reveal the defects that exist in the diamond material, which are dominated by non-electrically active linear dislocations. However, many diamonds also contain defects configurations (groups of threading dislocations originating from a secondary phase region or inclusion) in the bulk of the wafer which map well to regions of photoconductive gain, indicating that these inclusions are a source of electron trapping which affect the performance of diamond X-ray detectors. It was determined that photoconductive gain is only possible with the combination of an injecting contact and charge trapping in the near surface region. Typical photoconductive gain regions are 0.2 mm across; away from these near-surface inclusions the device yields the expected diode responsivity.

43 PARTICLE ACCELERATORS↗

Synchrotron X-Ray Topography Study of Structural Defects and Strain in Epitaxial Structures of Yb- and Tm-Doped Potassium Rare-Earth Double Tungstates and Their Influence on Laser Performance.

Monoclinic potassium rare-earth double tungstates [KRE(WO{sub 4}){sub 2}, RE = Y, Lu, Yb; KREW] are well suited as hosts for active lanthanide ion (Ln{sup 3+}) dopants for diode-pumped solid-state lasers, with particular interest in thin-disk laser configurations when they are grown as thin films. Using synchrotron white-beam x-ray topography, we have imaged defects and strain in top-seeded solution-grown (TSSG) bulk substrates of different rare-earth tungstates as well as within Yb{sup 3+}- and Tm{sup 3+}-doped epitaxies for thin-disk laser applications grown on these substrates by liquid-phase epitaxy. Higher structural stress in Yb:KYW/KYW epitaxies compared with Yb:KLuW/KLuW epitaxies is found to lower efficiency in laser operation. The quality of Tm:KLuW/KLuW epitaxial films is sensitive to doping level, film thickness, and growth rate. Inhomogeneous stresses within the layers are dominated by lattice-mismatch effects rather than by crystallographic anisotropy.

36 MATERIALS SCIENCE↗

Comments on ‘‘Analysis of Twin Formation in Sphalerite-type Compound semiconductors:A Model Study on Bulk InP Using Statistical Methods by M. Neubert, A. Kwasniewski and R. Fornari’’ J.Crystal Growth 310 (2008) 5270

The authors found no correlation between crystal growth angle and twinning incidence. This is contrary to the predictions of the Hurle model. A possible explanation for this is presented here. It is shown that the spatial resolution of their measurement of growth angle was insufficient to determine its value at the point at which twinning was initiated. Their measured value represents an average over a growth time, which was large compared to the likely characteristic temperature fluctuation time. Therefore the author's conclusion that 'the role of slope angle seems to be obscured by much stronger forces.' cannot properly be inferred from their data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Demonstration of Boron Arsenide Heterojunctions: A Radiation Hard Wide Band Gap Semiconductor Device

B{sub 12}As{sub 2}/SiC pn heterojunction diodes based on the radiation-hard B{sub 12}As{sub 2} deposited on (0001) n-type 4H-SiC via chemical vapor deposition were demonstrated. The diodes exhibit good rectifying behavior with an ideality factor of 1.8 and a leakage current as low as 9.4 x 10{sup -6} A/cm{sup 2}. Capacitance-voltage measurements using a two-frequency technique showed a hole concentration of - 1.8-2.0 x 10{sup 17} cm{sup -3} in B{sub 12}As{sub 2} with a slight increase near the interface due to the presence of an interfacial layer to accommodate lattice mismatch. Band offsets between the B{sub 12}As{sub 2} and SiC were estimated to be - 1.06 eV and 1.12 eV for conduction band and valance band, respectively.

36 MATERIALS SCIENCE↗

Energy Band Structure and Optical Response Function of Icosahedral B12As2: A Spectroscopic Ellipsometry and First-principles Calculational Study

An experimental and theoretical study on the dielectric-response function of icosahedral B{sub 12}As{sub 2} in the spectral region between 1.24 and 9.8 eV is presented. Comprehensive experimental information on the energy band structure from the analysis of features in the optical dispersion was complemented by spin-orbit first-principles calculations. The lowest indirect band gap width is 3.2 eV; the two lowest direct interband transitions are at 3.46 and 3.9 eV. High-energy critical points are assigned to specific electron transitions in the Brillouin zone and their dimensionality was determined. The static dielectric constant of B{sub 12}As{sub 2} is uniaxially anisotropic with values of 7.84 and 9.02 for polarization perpendicular and parallel to the trigonal axis. Hole and electron effective masses are derived from the band dispersions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

X-ray Characterisation of Zinc Oxide (ZnO) Single Crystal Substrates

Single crystal substrates of low defect density are paramount for fully realizing the numerous applications of zinc oxide (ZnO) wide bandgap semiconductors. While ZnO substrates are commercially available from various vendors, very little information is available on the structural properties of these substrates. Therefore, an extensive evaluation of available substrates would serve as a basis for the development of ZnO based devices and technologies. In this study, bulk ZnO single crystal substrates grown by different growth techniques have been characterised using synchrotron white beam X-ray topography and high resolution X-ray diffraction. The substrates exhibit a wide range of dislocation densities from as high as 10{sup 6} cm{sup -2} down to less than 1000 cm{sup -2} depending on the growth technique employed. The authors evaluation reveals that ZnO crystals grown by the hydrothermal technique possess the best structural quality with dislocation densities of 800-1000 cm{sup -2} and rocking curves with a full width half maximum of less than 12 arc seconds.

36 MATERIALS SCIENCE↗

Characterization of 100 mm diameter 4H-silicon carbide crystals with extremely low basal plane dislocation density

Synchrotron White Beam X-ray Topography (SWBXT) studies are presented of basal plane dislocation (BPD) configurations and behavior in a new generation of 100mm diameter, 4H-SiC wafers with extremely low BPD densities (3-4 x 10{sup 2} cm{sup -2}). The conversion of non-screw oriented, glissile BPDs into sessile threading edge dislocations (TEDs) is observed to provide pinning points for the operation of single ended Frank-Read sources. In some regions, once converted TEDs are observed to re-convert back into BPDs in a repetitive process which provides multiple BPD pinning points.

36 MATERIALS SCIENCE↗

Nucleation of c-axis Screw Dislocations at Substrate Surface Damage During 4H-silicon Carbide Homo-epitaxy

Observations of dislocation nucleation occurring at substrate surface scratches during 4H-SiC CVD homoepitaxial growth are reported. Sub-surface residual damage associated with the scratches is observed to act as nucleation sites for basal plane dislocations (BPDs), threading edge dislocations (TEDs) and threading screw dislocations (TSDs) in the epilayer. TEDs and BPDs replicate from the surface intersections of basal plane dislocation half-loops injected into the substrate surface. A model for the nucleation mechanism of TSDs, which nucleate in opposite sign pairs, is presented which involves overgrowth of surface indentations associated with the scratch during step flow growth. Atomic steps which approach these local surface indentations can collapse creating pairs of opposite sign screw dislocations which have Burgers vector magnitude equal to the magnitude of the step disregistry created during the collapse.

36 MATERIALS SCIENCE↗

Investigation of Character and Spatial Distribution of Threading Edge Dislocations in 4H-SiC Epilayers by High-Resolution Topography

Topography image variation of threading edge dislocations (TEDs) in 4H-SiC epilayers has been investigated by grazing incidence high-resolution synchrotron topography. Six different images of TEDs resulting from an angle between the diffraction vector and the TED Burgers vector were confirmed by correlation between experimental topography images and simulation results. The TED-type distribution, dependent on the direction of the TED Burger vector, was examined on epitaxial wafers, while the spatial distribution of TEDs on a whole 2 in wafer along [1 1 2 0] and [1 1 0 0] was investigated.

36 MATERIALS SCIENCE↗

Effect of Structural Stress on the Laser Quality of Highly Doped Yb:KY(WO4)2/KY(WO4)2 and Yb:KLu(WO4)2/KLu(WO4)2 Epitaxial Structures

In this communication we demonstrate how the difference in laser performance of two highly doped (20 at %) epitaxial layers of Yb-doped KY(WO4)2 (KYW) grown on a KYW substrate and Yb-doped KLu(WO4)2 (KLuW) grown on a KLuW substrate, respectively, is related to the presence of structural stress in the epilayers, investigated by synchrotron white beam X-ray topography. From the results obtained, it is clear that the samples that show a larger amount of structural stress, Yb:KYW/KYW epitaxies, lead to lower efficiency in laser operation, giving a direct correlation between the existence and magnitude of such structural stress and the loss in efficiency of laser performance in such epitaxial layers which, from a spectroscopical point of view, are otherwise equivalent.

43 PARTICLE ACCELERATORS↗