Search NASA⌕ Search

Engineering topics

Dudley, M

Publications and source records attributed to Dudley, M.

44 records · Page 3

Reduction of Chemical Reaction Mechanism for Halide Assisted Silicon Carbide Epitaxial Film Deposition

Simulation of gas-phase and surface chemistry is an essential part in numerical study of chemical vapor deposition for film growth. When integrated with a model for transport processes such as gas flow, heat transfer, and mass transfer, it allows the prediction of gas-phase composition, film deposition rate, and film uniformity. For halide-assisted chemical vapor deposition of silicon carbide film growth, three-dimensional simulation of the deposition process can be time-consuming due to the large number of chemical reactions involved. In this study, a simplified chemical reaction mechanism was developed for silicon carbide growth with silicon tetrachloride and propane as precursors. After model validation, the reduced reaction steps were implemented into a three-dimensional simulation of halide-assisted chemical vapor deposition to predict the distributions of gas velocity, temperature, concentration of the intermediate reactants, and film deposition rate. Specifically, the effects of deposition pressure on the film growth were investigated. The integrated model for chemistry and transport process demonstrated the capability of modeling a deposition process with reasonable computing time. We envision that this model will provide a useful tool for design, test, and optimization of the deposition process for growing silicon carbide films or bulk crystals by use of halide-assisted chemical vapor deposition process.

36 MATERIALS SCIENCE↗

Nucleation Mechanism of Dislocation Half-Loop Arrays in 4H-Silicon Carbide Homo-Epitaxial Layers

A model is presented for the formation mechanism of dislocation half-loop arrays formed during the homoepitaxial growth of 4H-SiC. The reorientation during glide of originally screw oriented threading segments of basal plane dislocation (BPD) renders them susceptible to conversion into sessile threading edge dislocations (TEDs), which subsequently pin the motion of the BPD. Continued glide during further growth enables parts of the mobile BPD to escape through the surface leaving arrays of half loops comprising two TEDs and a short BPD segment with significant edge component. The faulting behavior of the arrays under UV excitation is consistent with this model.

36 MATERIALS SCIENCE↗

Micropipe Dissociation through Thick n+ Buffer Layer Growth

Thick (> 25 {mu}m) 4H n+ epitaxial layer growth was performed on 4H n+ substrates utilizing chlorine containing etch chemistries in a hot wall CVD system. Optimization of the n+ epitaxial layer growth was achieved by varying C/Si ratio and N2 flow. Desired epitaxial layers have doping levels > 5x1018 cm-3, epitaxial surface roughness <10 nm on a 20x20 {mu}m area and overall micropipe density reduction. To confirm the conversion of micropipes into closed core screw dislocations, microscopic examination of the epitaxial and wafer surfaces was carried out after KOH etching. Grazing incidence x-ray topography (XRT) as well as cross sectional XRT and microscopy were also performed. The cross sectional evaluation showed that the dissociation of the micropipes occurs very close to the epitaxy/wafer interface.

36 MATERIALS SCIENCE↗

Aspects of Dislocation Behavior in SiC

A review is presented of the current understanding of the dislocation configurations observed in PVT-grown 4H- and 6H-SiC boules and CVD-grown 4H-SiC homoepitaxial layers. In both PVT-grown boules and CVD-grown epilayers, dislocation configurations are classified according to whether they are growth dislocations, i.e., formed during growth via the replication of dislocations which thread the moving crystal growth front, or result from deformation processes (under either mechanical or electrical stress) immediately following growth, during post growth cooling, i.e., behind the crystal growth front or during device operation. Possible formation mechanisms of growth defects in the PVT grown boules, such as axial screw dislocations and threading edge dislocation walls are proposed. Similarly, possible origins of growth defect configurations in CVD-grown epilayers, such as Frank faults bounded by Frank partials, BPDs and TEDs, are also discussed. In a similar way, the origins of BPD configurations resulting from relaxation of thermal stresses during post-growth cooling of the PVT boules are discussed. Finally, the susceptibility of BPD configurations replicated into CVD grown epilayers from the substrate towards Recombination Enhanced Dislocation Glide (REDG) is discussed.

36 MATERIALS SCIENCE↗

Studies of the Distribution of Elementary Threading Screw Dislocations In 4H Silicon Carbide Wafer

The density and sense distribution of elementary threading screw dislocations in a physical vapor transport grown 3-inch 4H silicon carbide wafer have been studied. The density of TSDs ranges between 1.6x103/cm2 and 7.1x103/cm2 and the lowest density is observed at positions approximately half radius off the wafer center. The dislocation sense of elementary threading screw dislocations can be readily revealed by the asymmetric contrast of their images in grazing-incidence x-ray topographs using pyramidal plane reflections. The circumferential and radial distributions of the sense of elementary threading screw dislocations have been studied and no clear trends are observed in either distribution.

36 MATERIALS SCIENCE↗

High Resolution Topography Analysis on Threading Edge Dislocations in 4H-SiC Epilayers

Threading edge dislocations (TEDs) in a 4H-SiC epitaxial layer are investigated using high-resolution synchrotron topography. Six types of TED image are confirmed to correspond to the Burgers vector directions by a comparison of computer simulated images and observed topography images in crystal boundaries. Using a mapping method, a wide spatial distribution of the six types of TED is examined in a quarter section of a 2-inch wafer.

36 MATERIALS SCIENCE↗

Characterization of Dislocations and Micropipes in 4H n+ SiC Substrates

Etching of 4H-SiC wafers in molten KOH as a method for micropipe and dislocation density analysis was investigated. The obtained results were correlated with those of the synchrotron white beam x-ray topography. Heavily nitrogen-doped SiC shows a significantly different etching behavior in comparison with the low-doped material. This complicates identification of different types of threading defects. In particular, it is difficult to separate Threading Screw Dislocations (TSD) from Threading Edge Dislocations (TED). Depending on the level of doping and thermal history of the crystal, some of the etch pits emerging due to the 1c screw dislocations can be as large as those due to the micropipes.

36 MATERIALS SCIENCE↗

Synchrotron X-ray Topographic Studies of Recombination Activated Shockley Partial Dislocations in 4H-SiC Epitaxial Layers

Electron-hole recombination activated Shockley partial dislocations bounding expanding stacking faults and their interactions with threading dislocations have been studied in 4H-SiC epitaxial layers using synchrotron x-ray topography. The bounding partials appear as white stripes or narrow dark lines in back-reflection X-ray topographs recorded using the basal plane reflections. Such contrast variations are attributable to the defocusing/focusing of the diffracted X-rays due to the edge component of the partial dislocations, which creates a convex/concave distortion of the basal planes. Simulation results based on the ray-tracing principle confirm our argument. The sign of the partial dislocations can be subsequently determined.

43 PARTICLE ACCELERATORS↗