Search NASA⌕ Search

Engineering topics

Duenow, Joel

Publications and source records attributed to Duenow, Joel.

Alternative Rear Contacts for Ultrathin CdSexTe1-x Solar Cells

The back contact is a key component for further developments of CdSeTe solar cells. In this contribution, we investigate several materials and designs that could help the development of highly-reflective, ohmic back contacts for conventional (3.45 um) and thin (800 nm) CdSeTe solar cells. We also explore numerically, nanostructured metal back contacts for light-trapping in ultrathin (200 nm) CdTe solar cells.

back contact↗

Developing CdTe homojunctions applying high throughput deposition

In this project, we attempted to make CdTe homojunctions using single crystal p-type doped substrates and closed-space sublimation epitaxy (CSSE) n-type doped films. The project included modeling which determined the ideal thickness for the n-type layer as being <200 nm. Boules of high concentration indium-doped CdTe and CdSe 0.4 Te 0.6 (CST) were grown using modified vertical Bridgman (MVB) methods. Similarly, iodine-doped CdTe crystals were grown for the first time. Washington State University (WSU) stock phosphorus-doped CdTe was used as the p-type substrate layer. The crystals were characterized by Hall effect and time-resolved photoluminescence (TRPL, for electrical properties), photoluminescence microscopy (for uniformity), X-ray diffraction (for crystal structure), and glow discharge mass spectrometry (GDMS, for dopant and impurity concentration). CdTe:I crystals were also characterized by visible and infrared transmission measurements, and various Cd or Te heat treatments were performed to assess changes in optical and electrical properties. The grown n-type materials – CdTe:In, CdSe0.4Te0.6:In, and CdTe:I – were provided to the National Renewable Energy Laboratory (NREL) for growth of CSSE thick films for characterization by two photon TRPL (for carrier lifetime), electron back-scatter diffraction (EBSD, to assess epitaxy), and Hall effect. Several measurements of secondary ion mass spectroscopy (SIMS) were performed. Nearly 100% of the indium from the crystal was incorporated into the measured thick films, while only ~2-22% of the iodine from the crystal was incorporated. The net result of the diffusion issue is that homojunction devices created using CSSE have a buried homojunction, as indicated by the near infrared peak in the external quantum efficiency (EQE). Various parameterization of front and back contacts suggested that the poor device performance was primarily a result of this buried junction and not due to other effects. There may also be an issue with the CSSE film lifetime in addition to the dopant profile.

14 SOLAR ENERGY↗

Investigating the Role of Copper in Arsenic Doped CdSeTe Photovoltaic Devices

As part of NREL's development of arsenic doped CdSeTe devices, co-doping with copper has become a common practice and, despite little difference in carrier concentration (often ~1016 cm-3), co-doped devices regularly show improved Voc. Given the critical importance of improving Voc, we are investigating this trend with a wide variety of characterization techniques including SEM, EBSD, SIMS, PL, CL, XPS, TRPL, JVT, KPFM, and DLTS. Together these indicate that Cu facilitates improved absorber-buffer interface properties and potentially improved bulk absorber characteristics, though specific mechanisms have not yet been determined. Despite the improved performance of co-doped devices, Voc is still far below its potential, and we explore the possibility that this limitation is the result of low buffer doping in conjunction with high absorber doping.

arsenic doping↗

Developing a Low Cost, High Volume and Scalable Manufacturing Technology for Undoped and Heavily P-Type Doped CdTe Feedstock Materials (Final Report)

The goal of this project was to establish a cost-effective and scalable production approach of feedstock (CdTe and Cd-Se-Te) for the solar industry, with the material properties necessary to improve performance and reduce costs. The primary focus was to develop a CdTe synthesis and growth process that pushed the p-type doping of CdTe to previously unattainable levels, while creating a path to scalable production. In our approach, the first step was bulk CdTe growth doped with Group V dopants (P, As, and Sb) using the Modified Vertical Bridgman (MVB) and high Pressure Bridgman (HPB) techniques, and the second step was examination of films deposited by Close-Spaced Sublimation (CSS) and Vapor Transport Deposition (VTD) using this specialized feedstock.

14 SOLAR ENERGY↗

High Efficiency Evaporated CdSeTe/CdTe Solar Cells With and Without MgZnO Buffer Layer

High efficiencies of ~19% CdTe solar cell devices were made using a thermal evaporation technique to deposit absorber layers of CdSe and CdTe. The absorber films were very high quality for a device fabrication, and with demonstrated high efficiency, it is a viable option to employ thermal evaporation in research and manufacturing. We also investigated four different interfaces scenarios of with and without MZO and CdSe in the device near front interface. The results clearly indicate that Se plays a key role in improving device performance, but the MZO is not necessarily required unless experiment goals demanded. Removing the MZO layer from the device structure and being able to use thermal evaporator for CdTe deposition will help with cost reduction in manufacturing.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Synthesis of CdSeCdSexTe1-x/CdTe for Graded Solar Cells

Here, we have developed CdSe x Te 1-x /CdTe bilayer deposition for graded solar cell technology. Smoothly graded Se profiles with > 16% efficiency with Jsc=28 m A/cm 2 and 20-ns bulk lifetime has been observed observed. The CdSeTe reveals longer carrier lifetimes than CdTe within the same device.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Roles of bandgrading, lifetime, band alignment, and carrier concentration in high-efficiency CdSeTe solar cells

CdSeTe alloying has significantly increased the efficiency of CdTe-based solar technology. Here, computational modeling compares how different CdSeTe bandgrading, carrier lifetimes, band alignment, and carrier concentrations contribute to transport, recombination, and performance. We find that the gain in photocurrent caused by bandgap narrowing alone is insufficient to describe experimental efficiency gains. Performance can be increased by adjusting CdSeTe compositions and bandgrading depths. However, these performance gains are small relative to the contributions of enhanced lifetime by Se alloying, which can explain record cell efficiency gains with minimal open-circuit voltage loss despite significant bandgap narrowing. Similarly, CdSeTe band alignment shifts can significantly increase performance if front interface recombination is prevalent. For a wide range of CdSeTe grading profiles, the hole density is a critical component to achieve efficiencies exceeding 25%.

36 MATERIALS SCIENCE↗

Overcoming Carrier Concentration Limits in Polycrystalline CdTe Thin Films with In Situ Doping

Abstract Thin film materials for photovoltaics such as cadmium telluride (CdTe), copper-indium diselenide-based chalcopyrites (CIGS), and lead iodide-based perovskites offer the potential of lower solar module capital costs and improved performance to microcrystalline silicon. However, for decades understanding and controlling hole and electron concentration in these polycrystalline films has been extremely challenging and limiting. Ionic bonding between constituent atoms often leads to tenacious intrinsic compensating defect chemistries that are difficult to control. Device modeling indicates that increasing CdTe hole density while retaining carrier lifetimes of several nanoseconds can increase solar cell efficiency to 25%. This paper describes in-situ Sb, As, and P doping and post-growth annealing that increases hole density from historic 10 14 limits to 10 16 –10 17 cm −3 levels without compromising lifetime in thin polycrystalline CdTe films, which opens paths to advance solar performance and achieve costs below conventional electricity sources.

14 SOLAR ENERGY↗

Influence of CdTe Deposition Temperature and Window Thickness on CdTe Grain Size and Lifetime After CdCl 2 Recrystallization

Grain structure influences both transport and recombination in CdTe solar cells. Larger grains generally are obtained with higher deposition temperatures, but commercially it is important to avoid softening soda-lime glass. Furthermore, depositing at lower temperatures can enable different substrates and reduced cost in the future. We examine how initial deposition temperatures and morphology influence grain size and lifetime after CdCl 2 recrystallization. Techniques are developed to estimate grain distribution quickly with low-cost optical microscopy, which compares well with electron backscatter diffraction data providing corroborative assessments of exposed CdTe grain structures. Average grain size increases as a function of CdCl 2 temperature. For lower temperature close-spaced sublimation CdTe depositions, there can be more stress and grain segregation during recrystallization. However, the resulting lifetimes and grain sizes are similar to high-temperature CdTe depositions. The grain structures and lifetimes are largely independent of the presence and/or interdiffusion of Se at the interface, before and after the CdCl 2 treatment.

14 SOLAR ENERGY↗

Obtaining Large Columnar CdTe Grains and Long Lifetime on Nanocrystalline CdSe, MgZnO, or CdS Layers

CdTe solar cells have reached efficiencies comparable to multicrystalline silicon and produce electricity at costs competitive with traditional energy sources. Recent efficiency gains have come partly from shifting from the traditional CdS window layer to new materials such as CdSe and MgZnO, yet substantial headroom still exists to improve performance. Thin film technologies including Cu(In,Ga)Se2, perovskites, Cu2ZnSn(S,Se)4, and CdTe inherently have many grain boundaries that can form recombination centers and impede carrier transport; however, grain boundary engineering has been difficult and not practical. In this work, it is demonstrated that wide columnar grains reaching through the entire CdTe layer can be achieved by aggressive postdeposition CdTe recrystallization. This reduces the grain structure constraints imposed by nucleation on nanocrystalline window layers and enables diverse window layers to be selected for other properties critical for electro-optical applications. Computational simulations indicate that increasing grain size from 1 to 7 um can be equivalent to decreasing grain-boundary recombination velocity by three orders of magnitude. Here, large high-quality grains enable CdTe lifetimes exceeding 50 ns.

14 SOLAR ENERGY↗

Controlling the stoichiometry and doping of semiconductor materials

Methods for treating a semiconductor material are provided. According to an aspect of the invention, the method includes annealing the semiconductor material in the presence of a compound that includes a first element and a second element. The first element provides an overpressure to achieve a desired stoichiometry of the semiconductor material, and the second element provides a dopant to the semiconductor material.

36 MATERIALS SCIENCE↗

Opto-Electronic Characterization CdTe Solar Cells from TCO to Back Contact with Nano-Scale CL Probe

We used cathodoluminescence (CL) (spectrum-per-pixel) imaging on beveled CdTe solar cell sections to investigate the opto-electronic properties of these devices from the TCO to the back contact. We used a nano-scale CL probe to resolve luminescence from grain boundary (GB) and grain interior (GI) locations near the CdS/CdTe interface where the grains are very small. As-deposited, CdCl2-treated, Cu-treated, and (CdCl2+Cu)-treated cells were analyzed. Color-coded CL spectrum imaging maps on bevels illustrate the distribution of the T=6 K luminescence transitions through the depth of devices with unprecedented spatial resolution. The CL at the GBs and GIs is shown to vary significantly from the front to the back of devices and is a sensitive function of processing. Supporting D-SIMS depth profile, TRPL lifetime, and C-V measurements are used to link the CL data to the J-V performance of devices.

14 SOLAR ENERGY↗

Resetting the Defect Chemistry in CdTe

CdTe cell efficiencies have increased from 17% to 21% in the past three years and now rival polycrystalline Si [1]. Research is now targeting 25% to displace Si, attain costs less than 40 cents/W, and reach grid parity. Recent efficiency gains have come largely from greater photocurrent. There is still headroom to lower costs and improve performance by increasing open-circuit voltage (Voc) and fill factor. Record-efficiency CdTe cells have been limited to Voc <; 880 mV, whereas GaAs can attain Voc of 1.10 V with a slightly smaller bandgap [2,3]. To overcome this barrier, we seek to understand and increase lifetime and carrier concentration in CdTe. In polycrystalline structures, lifetime can be limited by interface and grain-boundary recombination, and attaining high carrier concentration is complicated by morphology.

14 SOLAR ENERGY↗