Search NASA⌕ Search

Engineering topics

Dunn, Bruce

Publications and source records attributed to Dunn, Bruce.

At least 19 records

Transforming nanoscale VO 2 (B) into a scalable sodium-ion electrode

The intermittent nature of renewable energies requires highly reliable grid-level energy storage approaches. A critical consideration in developing this technology is the areal capacity which determines battery performance and influences the cost of battery technology. Of related importance is finding new ways of developing scalable electrodes. In recent years, three-dimensional (3D) printing of conductive scaffolds has emerged as an alternative to overcome the scalability limitations of commercial tape cast electrodes. The research carried out in the current study demonstrates a successful scalability pathway for nanoscale VO 2 (B), a desirable cathode for sodium-ion batteries which has a nano-flower morphology with a crystallite size < 20 nm. By electrodepositing VO 2 (B) onto a graphene aerogel scaffold, we were able to achieve mass loading of over 100 mg·cm −2 and still possess an areal capacity of 10 mAh·cm −2 at a current density of 5 mA·cm −2 . Moreover, after 1000 cycles, these electrodes retained 75% to 80% of their initial capacity. Even at high loading levels, the electrodeposited VO 2 (B) exhibits pseudocapacitive material signatures such as a box-like voltammetry response, linear galvanostatic response, and no phase change upon lithiation. The scalability of the VO 2 (B) electrode is demonstrated in a series of experiments which show the areal capacity to scale upon increase in both mass loading and electrode thickness, with only small changes in specific capacity. Furthermore, this study establishes that nanoscale materials can be scaled up to achieve thick electrodes without compromising their electrochemical properties.

additive manufacturing↗

Thermally Insulating Transparent Barrier (THINNER) coatings on single pane windows

Conventional silica aerogel monoliths can provide remarkable thermal insulation but the presence of large pores (> 30 nm) tends to scatter visible light and render the material opaque or translucent instead of transparent. In addition, they are prone to cracking during synthesis and handling which makes them difficult to integrate in products and in particular in window solutions. This project developed two new solgel synthesis methods using silica precursors or preformed silica nanoparticles and ambient drying to produce mesoporous organo-silica monoliths. The monoliths were (i) thermally insulating, (ii) optically transparent, (iii) flexible, and (iv) hydrophobic. They feature porosity ranging from 50% to 90% with narrow pore size distribution with pore less than 20 nm resulting in excellent optical clarity (haze < 2%) and very low thermal conductivity (< 30 mW/mK). Interestingly, not only porosity but also pore size and mass fractal dimension were found to affect the thermal conductivity of the mesoporous silica. The superior transparency of the monoliths was shown to be attributed to dependent scattering among silica nanoparticles. Flexibility was achieved through trimethylchlorosilane surface modification. Furthermore, process scale-up and integration of the ambigel monoliths into window solutions using optically clear adhesives were also demonstrated in 6”x6” double-pane windows. The aerogel and the window solution were shown to be durable to accelerated aging under UV, moisture, and/or temperature gradient and thermal cycling. Overall, the window solution achieved the technical performance and the cost target of $10/sqft set for the SHIELD program. However, scaling to industry relevant scale (> 10’x10’) remains a challenge due to requirements on the drying process and fume hood size and to the propensity of large aerogel slab to crack during drying.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Structure and Electrochemical Properties of Bronze Phase Materials Containing Two Transition Metals

Bronze phase transition-metal oxides have recently attracted attention as high-rate lithium-ion battery anode materials. Their crystal structures are distinguished by large tunnels and an open framework, facilitating lithium-ion diffusion and high-rate charge–discharge properties. The presence of two transition metals also offers a route to achieve high energy density from multielectron redox. In this paper, we report the chemistry, structure, and electrochemical properties of two different bronze phase compositions having the same stoichiometry: W 3 Nb 2 O 14 and Mo 3 Nb 2 O 14 . These materials provide insight into how the transition metals affect the electrochemical behavior and structural stability of bronze phase materials. Mo 3 Nb 2 O 14 exhibits greater than 1 electron redox per transition metal leading to lithium capacities above 200 mAh g –1 at C/2 but is unable to maintain this high capacity at high rates due to incomplete Mo redox reactions. In contrast, W 3 Nb 2 O14 exhibits reversible redox reactions and retains its open structure on cycling. This study highlights the potential of bronze phase materials containing two transition metals to exhibit fast charging properties with a high energy density.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Innovative Design and Manufacturing of 2.5D Battery with High Energy and Power Density (Final Report)

The goal of this project is to develop cathode inks, to be used in additive manufacturing (AM), that lead to a low-cost, fast manufacturing processes for a new type of non-planar, 2.5D lithium-ion battery (LIB). 2.5D batteries, comprised of a high-aspect-ratio 3D electrode combined with a 2D planar electrode, can simplify the fabrication process because there is no need for the alignment steps seen in traditional 3D batteries. For the success of the two AM processes identified in this project, development of cathode inks is key component because it allows for both platforms to be evaluated in achieving high performance batteries and ease of manufacturing. The two AM processes explored in this project are direct ink writing (DIW) and templating. Both of these processes have been shown to be successful in depositing materials for traditional LIBs and will be used now for the 3D array electrode configuration as part of the 2.5D battery.

25 ENERGY STORAGE↗

Understanding the Electrochemical Performance of FeS 2 Conversion Cathodes

Conversion cathodes represent a viable route to improve rechargeable Li + battery energy densities, but their poor electrochemical stability and power density have impeded their practical implementation. Here, we explore the impact cell fabrication, electrolyte interaction, and current density have on the electrochemical performance of FeS 2 /Li cells by deconvoluting the contributions of the various conversion and intercalation reactions to the overall capacity. By varying the slurry composition and applied pressure, we determine that the capacity loss is primarily due to the large volume changes during (de)lithiation, leading to a degradation of the conductive matrix. Through the application of an external pressure, the loss is minimized by maintaining the conductive matrix. Further, we determine that polysulfide loss can be minimized by increasing the current density (>C/10), thus reducing the sulfur formation period. Analysis of the kinetics determines that the conversion reactions are rate-limiting, specifically the formation of metallic iron at rates above C/8. While focused on FeS 2 , our findings on the influence of pressure, electrolyte interaction, and kinetics are broadly applicable to other conversion cathode systems.

Pressure↗

Mesoporous MoO 2 thin films for high rate Li + storage: Effect of crystallinity and porous structure

MoO 2 has attracted much recent attention as a high capacity energy storage material. While much of the current work on MoO 2 has been focused on the high capacity four-electron reduction, this reaction is limited to slow charging process due to the large volume change and phase transitions involved. In this study we focus on one-electron insertion reactions and demonstrate that ordered mesoporous thin films of MoO 2 can show signatures of pseudocapacitive charge storage. Mesoporous MoO 2 (mp-MoO 2 ) thin films were treated at different temperatures between 350 and 700 °C to explore the role of crystallinity and nanoscale structure on charging dynamics. The porosity and pore size decreased while the crystallinity and grain size increased as the calcination temperature increased. Materials processed at 600 °C showed the best electrochemical performance due to an optimized combination of high crystallinity and small grain size. These materials could be charged and discharged in 24 s while still achieving a Li + storage capacity of 158 mAh/g. While such thin film systems do not constitute a practical energy storage device, the work here provides structural design parameters for the production of future bulk nanoporous materials.

25 ENERGY STORAGE↗

Transparent silica aerogel slabs synthesized from nanoparticle colloidal suspensions at near ambient conditions on omniphobic liquid substrates

This paper presents a novel sol-gel method to synthesize large and thick silica aerogel monoliths at near ambient conditions using a commercial aqueous solution of colloidal silica nanoparticles as building blocks. To achieve slabs with high visible transmittance and low thermal conductivity, the method combines the strategies of (i) synthesizing gels on an omniphobic perfluorocarbon liquid substrate, (ii) aging at temperatures above room temperature, and (iii) performing solvent exchange with a low-surface-tension organic solvent prior to ambient drying. The omniphobic liquid substrates were used to prevent cracking and ensure an optically-smooth surface, while nanoparticle building blocks were small (<10 nm) to limit volumetric light scattering. Gels were aged at temperatures between 25 and 80 °C for up to 21 days to make them stronger and stiffer and to reduce shrinkage and cracking during ambient drying. Ambient drying was achieved by first exchanging water in the gel pores for octane, followed by drying in an octane-rich atmosphere to decrease capillary forces. The synthesized nanoparticle-based silica aerogel monoliths had thicknesses up to 5 mm, diameters up to 10 cm, porosities exceeding 80%, and thermal conductivities as low as 0.08 W m –1 K –1 . Notably, the slabs featured visible transmittance exceeding 75% even for slabs as thick as 5 mm. The as-synthesized aerogel monoliths were exposed to TMCS vapor to induce hydrophobic properties resulting in a water contact angle of 140° that prevented water infiltration into the pores and protected the aerogels from water damage. This simple synthesis route conducted at near ambient conditions produces hydrophobic aerogel monoliths with promising optically transparent and thermally insulating properties that can be adhered to glass panes for window insulation and solar-thermal energy conversion applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Challenges for and Pathways toward Li-Metal-Based All-Solid-State Batteries

Solid-state batteries utilizing Li metal anodes have the potential to enable improved performance (specific energy >500 Wh/kg, energy density >1500 Wh/L), safety, recyclability, and potentially lower cost (<$100/kWh) compared to advanced Li-ion systems.1,2 These improvements are critical for the widespread adoption of electric vehicles (EVs) and trucks and could create a short-haul electric aviation industry.1-3 Expectations for solid-state batteries are high, but there are significant materials and processing challenges to overcome.

25 ENERGY STORAGE↗

Plasma enhanced atomic layer deposition of thin film Li 1+x Mn 2-x O 4 for realization of all solid-state 3D lithium-ion microbatteries

Here, the plasma enhanced atomic layer deposition (PEALD) process for MnO 2 was demonstrated, exhibiting self-limiting growth as well as stable composition and stable growth rate over a temperature window of 205–265 °C. The PEALD process for MnO 2 was combined with the thermal ALD process for LiOH to synthesize Li 1+x Mn 2-x O 4 thin film cathodes, where the stoichiometry was effectively controlled to allow for crystallization in the electrochemically active spinel phase. A 3D nanostructure consisting of an Li 1+x Mn 2-x O 4 cathode layer, ALD Li x Al y Si z O solid electrolyte, and SiGe nanowire anode was fabricated and characterized via TEM. The Li 1+x Mn 2-x O 4 thin films maintained 66% of the areal capacity upon a 100× increase in the rate (4–360 μ A cm -2 ) as well as 97% capacity retention over 100 cycles at ~5C. The ALD Li 1+x Mn 2-x O 4 thin films exhibited a volumetric capacity of 52 μ Ah cm -2 μ m -1 at a C-rate of ~0.5C and, coupled with the high operating voltage (4.0 V), offer some of best areal energy densities for ALD thin film cathodes, making it a viable material for integration with 3D lithium-ion microbatteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and Crystallization of Atomic Layer Deposition β-Eucryptite LiAlSiO 4 Thin-Film Solid Electrolytes

Atomic layer deposition (ALD) was used to control the stoichiometry of thin lithium aluminosilicate films, thereby enabling crystallization into the ion-conducting β-eucryptite LiAlSiO 4 phase. Here, the rapid thermal annealed ALD film developed a well-defined epitaxial relationship to the silicon substrate: β-LiAlSiO4 ($1\bar{21}0$)||Si (100) and β-LiAlSiO 4 ($10\bar{10}$)||Si (001). The extrapolated room temperature ionic conductivity was found to be 1.2 × 10 –7 S/cm in the [$1\bar{21}0$] direction. Because of the unique 1-D channel along the c axis of β-LiAlSiO 4 , the epitaxial thin film has the potential to facilitate ionic transport if oriented with the c axis normal to the electrode surface, making it a promising electrolyte material for three-dimensional lithium-ion microbatteries.

25 ENERGY STORAGE↗

Challenges for and Pathways Toward Solid-State Batteries

Solid-state batteries utilizing lithium metal anodes have the potential to enable batteries with a specific energy of >500 Wh/kg and an energy density of >1,500 Wh/L for thousands of cycles. When optimized they will improve the energy efficiency, operating temperature range, sustainability, and safety at a lower cost compared to projections for advanced Li-ion batteries. This improved performance is critical for the widespread adoption of electric vehicles and may enable future applications such as electric aviation. Expectations for solid-state batteries are high, there are significant materials and processing challenges that need to be overcome. Some of these challenges are well known; others are more subtle and are just becoming known. The challenges and their solutions must be clearly identified to realize high-energy solid-state Li metal batteries. In the United States, the U.S. Department of Energy (DOE) funds the majority of energy storage research and development, including solid state battery research. Web of Science publication analysis shows that worldwide DOE is second largest funder. Work on solid state batteries is distributed across different arms of DOE and is coordinated at headquarters to ensure a broad national portfolio for advanced batteries, including lithium batteries and solid-state battery devices. We note that university and national laboratory researchers in the US with a long-standing interest in solid state batteries is a small, integrated community with recognized impact for publications, patents and startup companies. The opportunity for this group to engage for research with international colleagues is growing, fostered by periodic bilateral meetings supported by DOE and by the recent joint US German research program for lithium battery interface studies. These are valuable opportunities to speed solid-state battery development. The ORNL led virtual workshop, overviewed here, confirms the community’s shared vision of the exciting advances, opportunities, and challenges. Further, we are seeing that this workshop has spawned several new informal collaborations and draft proposals. This encourages us to propose future discussion. On May 11, 2020, Oak Ridge National Laboratory (ORNL) hosted a 6-hour, on-line national workshop to discuss recent advances and most the prominent obstacles to realizing solid-state Li metal batteries. The workshop included more than 30+ experts from national laboratories, universities, and companies, all of whom have worked on solid-state batteries for multiple years. The participants shared recent advances, many not yet in print, illustrating that the community has gained significant new insights for solid-state Li battery materials over the last 5 years. In this report, the major outcomes of the workshop are organized to identify the gaps in our scientific knowledge for four core materials science areas: (1) Li metal anodes, (2) the solid electrolyte in contact with Li metal, (3) active cathode materials and solid-state composite cathodes, and (4) solid electrolytes. Illustrative examples and discussions are reported with the more comprehensive issues in the report. Discussion of additional challenges related to processing of solid-state battery materials and to the designs and architectures for mechanically robust, long-lived batteries received less attention due to time constraints. These are good themes for deeper discussion at a follow-on workshop, where a complete list of critical research topics can be identified.

25 ENERGY STORAGE↗