Search NASA⌕ Search

Engineering topics

Eapen, Jacob

Publications and source records attributed to Eapen, Jacob.

Mechanisms of Retention and Transport of Fission Products in Virgin and Irradiated Nuclear Graphite

To fulfill the design and licensing requirements for advanced reactors, the U.S. Department of Energy (DOE) is specifically interested in targeted research to quantify the mechanisms of fission product transport and retention in graphitic grades that will likely be used in next-generation very/high temperature reactors, fluoride salt-cooled high temperature reactors and molten salt reactors. We have examined an integrated experimental-computational approach to determine the diffusivities of selected fission products – ruthenium (Ru) and silver (Ag) in five nuclear graphite grades – POCO AXF-5Q, POCO ZXF-5Q, PCEA, IG110, and NBG-18. Experimental investigation for diffusion of other fission products (iodine, cesium, and krypton) in graphite could not be carried out due to extreme evaporation due to high vapor pressure, despite several attempts incorporating various experimental schemes. Experimental investigation with irradiated graphite could not be carried out because necessary approval to transport irradiated graphite could not be obtained due to procedural reasons at ORNL and national policy change in UK. An effort was made to “produce” by ion sputtering, but it was discontinued because the outcome did not adequately represent irradiated graphite. Thin film and “cup-and-cap” methods were employed to deposit fission products, diffusion annealed were carried out in an argon atmosphere, and concentration profiles were determined by dynamic secondary ion mass spectroscopy depth profiling technique. Regardless of graphite type, anomalous diffusion behavior of Ru (i.e., lower than expected based on Arrhenius temperature dependence) at an intermediate temperature, around 600 to 700 °C, was observed. Diffusion behavior of silver on the other hand agreed well to the Arrhenius temperature dependence although the excessive evaporation of silver hampered the accurate determination of diffusivities at temperature higher than 900 °C. In general, silver was observed to diffuse faster than Ru in the temperature range compared from 500 to 900 °C, had consistently had higher pre-exponential factor corresponding to higher jump frequency. To understand the abnormal diffusional behavior of Ru in graphite in intermediate temperature range, a detailed microstructural analysis was carried out. Clustering of Ru into particles on the surface of graphite was observed around 700 °C corresponding to de-wetting and spheroidization. This change would influence the boundary condition of diffusion, although features of clustering was much smaller (<1 mm) than the SIMS raster size (120 x 120 mm). Raman spectroscopy also demonstrated that Raman peak intensity for Ru decreased significantly for samples annealed higher than 700 °C and presence of Ru in graphite altered the crystallinity of graphite. To further elucidate the abnormal diffusion behavior observed in intermediate temperature investigated, the vibrational properties of graphene, bilayer graphene and Kr atoms in bilayer graphene were investigated with molecular dynamics. Krypton, which is a fission product, was introduced between a bilayer graphene system to evaluate (i) whether the phonon dispersion curves change with high temperature in bilayer graphene (ii) whether the addition of Kr atoms between the bilayer introduces any significant change in the vibrational properties, and (iii) whether any change in the vibrational properties can be correlated to the diffusive behavior of Kr atoms. The results show that the Kr atoms indeed exhibit an anomalous diffusive behavior at 550°C. Phonon analysis shows that a few phonon frequencies are enhanced as much as 20 to 30 % with the addition of just 0.2 at.% Kr. So, this may explain the unexpected self-diffusivity of fission products.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Decoding ionic conductivity and reordering in cation-disordered pyrochlores

The ordered structure A 2 B 2 O 6 O’ in pyrochlores engenders twin rows of inequivalent anion sublattices each centred on alternating cations. While it is known that cation antisite disorder augments the ionic conductivity by several orders of magnitude, the local cation environment around the anions and the dynamic anion reordering during the cation disordering are not well-elucidated. Using atomistic simulations on Gd 2 Zr 2 O 7 , we first show that the anions engage in concerted hops to the neighbouring tetrahedral sites mostly along with the $\langle$1 0 0$\rangle$ direction while completely avoiding the octahedral sites. While the initially vacant 8 a sites start accommodating oxygen ions with increasing cation disorder, they show noticeable reluctance even at significant levels of disorder. We have also tracked both the distribution of available oxygen sites following random cation disorder, which is dependent only on cation disordering, and the probability of occupation of these sites. Interestingly, the available oxygen sites show a non-monotonic dependence on the number of B ions in the nearest neighbouring shell while the occupation probability of all the available oxygen sites increases monotonically. A tetrahedral oxygen site thus has a better probability of being occupied when it has a greater number of second neighbour B ions. This article is part of the Theo Murphy meeting issue 'Understanding fast-ion conduction in solid electrolytes'.

Science & Technology - Other Topics↗

Microstructure Experiments-Enabled MARMOT Simulations of SiC/SiC-based Accident Tolerant Nuclear Fuel System

We have undertaken an experimental-computational project that addresses a few key technology gaps associated with the use of SiC/SiC composites for light water reactor fuel cladding. Two principal endeavors in this project are to assess the irradiation-induced microstructural changes and swelling in SiC/SiC composites, and to characterize and model the porous oxide surface layer (when exposed to steam) along SiC recession that is detrimental to the clad integrity under accident conditions. The project tasks are: (i) ion irradiation and characterization (University of Tennessee, Knoxville), (ii) mechanical tests and analysis (University of South Carolina), (iii) steam exposure tests (Oak Ridge National Laboratory), (iv) electron microscopy and spectroscopic characterization (NC State University), (v) x-ray microscopy and reconstruction (University of South Carolina and NC State University), (vi) phase field modeling and simulations (NC State University and Idaho National Laboratory). The effects of 10 MeV Au ion irradiation at 350°C on the microstructure evolution in SiC/SiC composites are investigated at doses up to 400 displacements per atom (dpa) at the University of Tennessee, Knoxville. Atomic force microscopy and optical profilometry reveal irradiation induced axial and radial shrinkage of the fibers for doses greater than 10 dpa. Based on detailed electron microscopy characterization, the primary cause of the fiber shrinkage is attributed to irradiation-induced loss of carbon packets. Additionally, the multilayer PyC interface is observed to portray high resistance to irradiation damage. The mechanical response and failure mechanisms of un-irradiated samples is also assessed through loading tests and X-ray imaging at the University of South Carolina. Steam exposure tests are performed at the Oak Ridge National Laboratory in a facility that represents a reactor pressure vessel under a loss-of-coolant-accident scenario. The samples that are analyzed methodically in this report are tested for 32/31 hours at 1200°C with a velocity of 0.25 cm/s for the pressures: 0.1 MPa, 0.45 MPa, 0.92 MPa and 1.38 MPa. Scanning/transmission electron microscopy analysis conducted at the NC State University (NCSU) shows that the oxide layer thickness increases with the steam pressure. While the oxide layer is crystalline (α- cristobalite) for the pressures 0.45 MPa, 0.92 MPa and 1.38 MPa, the layer is amorphous at 0.1 MPa. Results from Raman spectroscopy have also confirmed the formation of α-cristobalite phase of SiO₂. The abrupt increase in the integrated Raman intensity ratio between steam pressures 0.1 and 0.45 MPa suggests the onset of accelerated crystallization. Non-destructive three dimensional X-ray microscopy/tomography (XCT) and computational image processing techniques are employed by the University of South Carolina to probe the porous oxidation features on SiC samples at varying pressures. Interestingly, most pores are observed to be located away from the surface as well as the oxide-SiC interface. The average oxide layer thickness assessed from the XCT analysis is seen to be in excellent agreement with the values determined through scanning electron microscopy analysis for the highest pressures where the oxide layer is relatively more uniform. A phase-field model developed by the NC State University and Idaho National Laboratory for simulating oxidation of SiC by steam captures the paralinear kinetics of SiC oxidation with a high degree of fidelity. Results from quasi-one-dimensional and two dimensional simulations show that the pores with oxidizing species lead to a higher volatilization rate. These simulations indicate that the enhanced apparent volatilization rates at higher pressures observed in experiments can be rationalized by the increased volatilization from the pores. The project team has also successfully developed the capability to import images from experiments for realistic evolution of the oxidizing microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Deducing Phonon Scattering from Normal Mode Excitations

While the quantum scattering theory has provided the theoretical underpinning for phonon interactions, the correspondence between the phonon modes and normal modes of vibrations has never been fully established; for example, the nature of energy exchange during elementary normal mode interactions remains largely unknown. In this work, by adopting a set of real asymmetric normal mode amplitudes, we first discriminate the normal and Umklapp processes directly from atomistic dynamics. We then demonstrate that the undulating harmonic and anharmonic potentials, which allow a number of interaction pathways, generate several total-energy-conserving forward and backward scattering events including those which are traditionally considered as quantum-forbidden. Although the normal mode energy is proportional to the square of the eigen-frequency, we deduce that the energy exchanged from one mode to another in each elementary interaction is proportional to the frequency – a quantum-like restriction. We anticipate that the current approach can be utilized profitably to discover unbiased scattering channels, many traditionally quantum forbidden, with complex anharmonicities. Our discovery will aid in the development of next-generation Peierls-Boltzmann transport simulations that access normal mode scattering pathways from finite temperature ab initio simulations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Topological Defects in Graphite under Irradiation using Molecular Dynamics

Graphite is the preferred material for moderating elements and structural components in a Very High Temperature Reactor (VHTR). It has a layered structure with basal planes constituted by carbon atoms arranged in a hexagonal lattice. Graphite accommodates a wide variety of defects such as vacancies, interstitials, and dislocation loops; a detailed description can be found in a review paper by Telling and Heggie. The layered configuration in graphite engenders energetic conditions that favor the formation of topological defects. Unlike the interlayer defects, which often are sp{sup 3} hybridized, topological defects maintain their sp{sup 2} bond connectivity. Several types of topological defects are known to arise in graphite; one of the most recognizable defects corresponds to a 5-7 Stone-Wales (SW) configuration that arises by a simple rotation of bonds. While the bond rotations result in a defected configuration, each carbon atom is still bonded to three other carbon atoms in the SW configuration, albeit with different bond lengths. Topological defects are expected to arise in irradiated graphite. A recent investigation with Raman and XPS spectroscopy have concluded that a large number of such defects are generated under neutron irradiation; an earlier ab-initio investigation has also arrived at the same conclusion. While several molecular dynamics (MD) simulations have been reported on irradiated graphite in the past, none have characterized the evolution of defects that are topological in nature. Using MD simulations, the current investigation quantifies the evolution and the distribution of topological defects under irradiation. Using MD simulations, we establish the presence of 5 and 7 membered topological defects in graphite following radiation. There is a greater probability for the formation of a 7 member ring relative to that of a 5 member ring. Since a heptagon causes a lower distortion to the 120 deg. bond angle of the sp{sup 2} hybridized orbital than a pentagon it is plausible to expect a larger number of 7 member rings following a radiation perturbation. Using a spatial distribution analysis, we have verified that 7 member rings tend to stay adjacent to 5 member rings as in Stone-Wales (SW) configuration. Since there are unequal number of 5 and 7 member rings, it follows that there are several isolated 7 member topological defects in graphite following radiation, possibly connected to dangling bonds or non-planar (sp{sup 3}) defects.

36 MATERIALS SCIENCE↗

String-Like Transport in Superionic Conductors

Superionic or fast-ion conductors are multicomponent solid-state systems in which one sublattice becomes mobile and exhibits extraordinarily high ionic conductivity before the melting within the solid state. Uranium dioxide (UO{sub 2}) - the fuel material of choice in most nuclear reactors - shows superionic behavior, although the mechanism of fast ion transport of the mobile oxygen ions, and its implication, is not well-understood. UO{sub 2} belongs to the category of Type II superionics wherein the conductivity rises gradually with increasing temperature, without an attendant phase change. In a recent work, using atomistic simulations and available neutron and x-ray scattering data, we have shown that all Type II superionic conductors exhibit a well-defined onset of dynamic disorder at a characteristic temperature T{sub α} = (∼2000 K for UO{sub 2}). Unlike the familiar superionic or Bredig transition temperature T{sub α} (∼2650 K for UO{sub 2}) that is associated with a second-order thermodynamic phase transition, T{sub α} represents an order-disorder (O-D) transition that marks a structural and kinetic crossover from a crystalline state to a semi-ordered state. In the temperature range between T{sub α} and T{sub λ}, the oxygen ions in UO{sub 2} exhibit jammed dynamics even though the mobile oxygen ions favor collective hopping from one native crystalline site to another. This cooperative dynamics manifests as dynamical heterogeneity (DH) - the tendency of highly mobile oxygen ions to form dynamic clusters, and dynamical facilitation (DF) - the mode of system relaxation facilitated solely through the kinetic ions transferring their mobility to neighboring ions. The jammed dynamics portrayed by the oxygen ions is similar to that observed in supercooled liquids and glassy materials, and other disordered systems such as granular media and polymers. In the current work, we probe the ionic dynamics in UO{sub 2} for the presence of another ubiquitous signature of glassy and jammed systems, namely, the one-dimensional string-like motion of the mobile species. Unlike the uncorrelated vacancy exchanges and interstitial migration in defected crystalline states, the string motion is a collective mechanism among the mobile species wherein each member of the string induces the next member to move in a correlated, sequential fashion. Using atomistic simulations, we demonstrate that oxygen ions in UO{sub 2} are transported through a string-like mechanism in the temperature range between T{sub α} and T{sub λ}, and the probability distribution of occurrence of the strings varies exponentially with string length. The discovery of string-like motion of the oxygen ions is somewhat surprising given the crystalline underpinning of the mobile species and the dynamic tendency of the oxygen ions to hop between lattice sites. In addition to dynamical heterogeneity and dynamical facilitation, our work has added one more entry, namely the occurrence of string-like transport, to the list of phenomenological similarities between superionic conductors and jammed systems. Using atomistic simulations, we have established the occurrence of string-like ionic motion among the oxygen ions in UO{sub 2} between temperatures T{sub α} - the order-disorder (O-D) transition temperature, and T{sub λ} - the Bredig transition temperature. As observed in other jammed systems, the length of the strings is observed to have an exponential distribution implying that the probability of occurrence of a smaller string is much higher than that of a longer string. Interestingly, using Temperature-Accelerated Dynamics (TAD) we have also established that string-like hopping takes place at temperatures lower than T{sub α}; these results will be published elsewhere. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Novel Engineered Refractory Materials for Advanced Reactor Applications

This report summarizes the results of DOE-NEUP grant 10-853. The project spanned 48 months (36 months under the original grant plus a 12 month no cost extension). The overarching goal of this work was to fabricate and characterize refractory materials engineered at the atomic scale with emphasis on their tolerance to accumulated radiation damage. With an emphasis on nano-scale structure, this work included atomic scale simulation to study the underlying mechanisms for modified radiation tolerance at these atomic scales.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Modeling irradiation creep of graphite using rate theory

In this work we examined irradiation induced creep of graphite in the framework of transition state rate theory. Experimental data for two grades of nuclear graphite (H-337 and AGOT) were analyzed to determine the stress exponent (n) and activation energy (Q) for plastic flow under irradiation. Here we show that the mean activation energy lies between 0.14 and 0.32 eV with a mean stress-exponent of 1.0 ± 0.2. A stress exponent of unity and the unusually low activation energies strongly indicate a diffusive defect transport mechanism for neutron doses in the range of 3-4 x 10 22 n/cm 2 .

36 MATERIALS SCIENCE↗

Mobility propagation and dynamic facilitation in superionic conductors

In an earlier work [V. A. Annamareddy et al., Phys. Rev. E 89, 010301(R) (2014)], we showed the manifestation of dynamical heterogeneity (DH)—the presence of clustered mobile and immobile regions—in UO{sub 2}, a model type II superionic conductor. In the current work, we demonstrate the mechanism of dynamic facilitation (DF) in two superionic conductors (CaF{sub 2} and UO{sub 2}) using atomistic simulations. Using the mobility transfer function, DF is shown to vary non-monotonically with temperature with the intensity of DF peaking at temperatures close to the superionic transition temperature (T{sub λ}). Both the metrics quantifying DH and DF show remarkable correspondence implying that DF, in the framework of kinematically constrained models, underpins the heterogeneous dynamics in type II superionic conductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

One-Dimensional Nanostructures for Neutron Detection

This report consists of four parts in addition to a publication/presentation list. Part I is on electronic structure simulations on boron nitride (BN) and BC x N nanotubes using density function theory (DFT), Part II is on fabrication and characterization of nanowire sensors, Part III is on irradiation response of BN nanotubes using molecular dynamics (MD) simulations, and Part IV is on the in-situ transmission electron microscopy (TEM) study of irradiation response of BN nanotubes.

36 MATERIALS SCIENCE↗

Understanding Creep Mechanisms in Graphite with Experiments, Multiscale Simulations, and Modeling

Disordering mechanisms in graphite have a long history with conflicting viewpoints. Using Raman and x-ray photon spectroscopy, electron microscopy, x-ray diffraction experiments and atomistic modeling and simulations, the current project has developed a fundamental understanding of early-to-late state radiation damage mechanisms in nuclear reactor grade graphite (NBG-18 and PCEA). We show that the topological defects in graphite play an important role under neutron and ion irradiation.

36 MATERIALS SCIENCE↗

Modeling Solute Thermokinetics in LiCl-KCl Molten Salt for Nuclear Waste Separation (NEUP 10-418)

Recovery of actinides is an integral part of a closed nuclear fuel cycle. Pyrometallurgical nuclear fuel recycling processes have been developed in the past for recovering actinides from spent metallic and nitride fuels. The process is essentially to dissolve the spent fuel in a molten salt and then extract just the actinides for reuse in a reactor. Extraction is typically done through electrorefining, which involves electrochemical reduction of the dissolved actinides and plating onto a cathode. Knowledge of a number of basic thermokinetic properties of salts and salt-fuel mixtures is necessary for optimizing present and developing new approaches for pyrometallurgical waste processing. The properties of salt-fuel mixtures are presently being studied, but there are so many solutes and varying concentrations that direct experimental investigation is prohibitively time consuming and expensive (particularly for radioactive elements like Pu). Therefore, there is a need to reduce the number of required experiments through modeling of salt and salt-fuel mixture properties. This project will develop first-principles-based molecular modeling and simulation approaches to predict fundamental thermokinetic properties of dissolved actinides and fission products in molten salts. The focus of the proposed work is on property changes with higher concentrations (up to 5 mol%) of dissolved fuel components, where there is still very limited experimental data. The properties predicted with the modeling will be density, which is used to assess the amount of dissolved material in the salt; diffusion coefficients, which can control rates of material transport during separation; and solute activity, which determines total solubility and reduction potentials used during electrorefining. The work will focus on La, Sr, and U, which are chosen to include the important distinct categories of lanthanides, alkali earths, and actinides, respectively. Studies will be performed using LiCl-KCl salt at the eutectic composition (58 mol% LiCl, 42 mol% KCl), which is used for treating spent EBR-II fuel. The same process being used for EBRII fuel is currently being studied for widespread international implementation. The methods will focus on first-principles and first- principles derived interatomic potential based simulations, primarily using molecular dynamics. Results will be validated against existing literature and parallel ongoing experimental efforts. The simulation results will be of value for interpreting experimental results, validating analytical models, and for optimizing waste separation by potentially developing new salt configurations and operating conditions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗