Engineering topics
Publications and source records attributed to Fedors, R. F..
Calculations of liquid absorption by rubber vulcanizates agree with experimental results. Equation allows calculation of swelling of rubber vulcanizates by liquids, based on knowledge of chemical structure of polymer and solvent. Calculated values agree favorably with experimental data.
Equation agrees with measurements over wide concentration range. Plot of calculated values from equation and measured values show close match except at extremely low concentrations of electrolyte. Other equations do not match data as well and limited to dilute solutions.
Permeation of liquid through polymer sheets retarded by including in polymer solute for excluded liquid. Long-term or steady state permeability not reduced by solute inclusions.
The stress-relaxation modulus of an unfilled ethylene vinyl acetate polymer at three different degrees of crosslinking was measured at 15 temperatures over a temperature span of about 160 C. At each temperature, the time response was measured for at least three decades of time. From these data it was possible to construct a master curve for each degree of crosslinking. The time-temperature shift factors, alpha(T), were found to be related to temperature by the relation log alpha(T) = -A(T - 273), where the parameter A has an average value of 0.234 for the three materials.
The direct measurement of physical aging and of the volume changes which go on during the course of this aging is discussed. Data on PMMA showing its physical aging as measured by its stress relaxation response and the accompanying volume changes are presented. An indication of how one can measure the free volume both directly from the volume change itself and relatively directly via a new technique is given. The application of this new technique (electron spin resonance spectroscopy) to other polymer systems is demonstrated.
The fracture toughness of an incorporation of a carboxyl-terminated butadiene acrylonitrile (CTBN) elastomer in diglycidyl ether bisphenol A (DGEBA) resin was investigated. Measurements of dynamic mechanical properties, scanning electron microscopy and small-angle X-ray scattering were carried out to characterize the state of cure, morphology and particle size and size distribution of the neat resins and their graphite fiber reinforced composites.
Equation based on model of flaw growth. Model assumes cell fails by growth of preexisting flaws. Flaws described by three important quantities: total number of flaws, distribution of flaw sizes and rate of flaw growth. When flaw reaches critical size failure occurs. Flaw concept, in addition to providing ready explanation for reduced lifetime, predicts two important charateristics: statistical variability of lifetime data and dependence of lifetime on volume of sample.
Explore the source record for details and available documents.
A test method is described for predicting the long-time survivability of elastomers in hydrazine under dynamic stressing conditions. The method selected is based upon the existence and approximate invariance of a 'physical property surface' relating the mechanical response of the elastomer in terms of stress, strain, time, and temperature. The property surface was generated for two selected elastomers (EPT-10 and AF-E-332). A novel carousel testing tank was designed to allow sequential testing of eight tensile specimens immersed in liquid hydrazine within a constant-temperature water bath. The test procedure and data reduction methods used to generate the property surface are described. The utility and validity of these results applied to fatigue and flexure loading to these elastomeric materials over long-time periods are discussed.
Formula with one adjustable parameter relates electrical resistivity of sintered metal plate to porosity of plate. Sintered plate formed by heating compressed metal powder- without melting- until particles adhere. Sintered nickel plates of high porosity used as substrates for electrodes in nickel/ cadmium batteries.
Combination of soluble particles and absorbed solvents cause polymer cracking. New failure mechanism in glassy polymers identified. Cracking caused by presence of particles insoluble in polymer matrix but soluble in solvent. Experiments performed and equations describe cracking phenomenon set forth in concise report.
The strain-birefringence response of poly(bisphenol-A-diphenyl sulfone) is found to be independent of temperature at temperatures below -100 C; at higher temperatures, the response becomes slightly dependent on temperature, with lower birefringence seen at higher temperatures. The stress-strain behavior and the stress-birefringence response both depend on temperature over the entire testing temperature range (-179 C to 150 C) studied; this dependence, however, is not pronounced. The evidence is seen as suggesting that the polymer molecules respond to deformation by undergoing conformational rearrangements; the mode of the molecular deformation remains unchanged for temperatures of -100 C or lower. At higher temperatures, the average length of the chain segments involved in the rearrangement increases. The stress-strain response is attributed mainly to chain orientation. The entropic contribution deriving from chain orientation at temperatures below -100 C is still substantial. The modest temperature dependence of the stress-strain response suggests that the energy barriers for the chain segments involved in the rearrangement are relatively low.
Technique minimizes effect of substrate on thin sintered coating. Uniaxial tension test yields approximate value for elastic modulus of sintered material on thin substrate. Electrode composed of central perforated nickel plated steel sheet about 4 mils (0.1mm) thick, coated on each face by porous sintered nickel about 8 mils (0.2mm) thick.
Degree of cross-linking or network chain concentration of rubber estimated with aid of new method. Quantity is needed in studies of mechanical behavior of rubber. New method is based on finding rubber follows different stress/ strain relationships in extension and retraction. When rubber specimen is stretched to given extension ration and released. Stress-vs-strain curve follows two paths: one for extension and other for retraction.
Explore the source record for details and available documents.
A model has been developed to describe failure in electrochemical batteries. The model is based on the concept of the existence and subsequent growth of flaws which ultimately lead to battery failure. This model provides, in a natural way, for the statistical variability of lifetime data. The model as applied to the Crane data indicates that when the effects of temperature and depth of discharge are taken into account, the observed variability in lifetime data is due almost entirely to statistical variability inherent in the battery itself.
The present investigation is concerned with the effect of both molecular weight and chemical structure on the critical temperature. Using data from the comprehensive compilation of critical constants of Kudchadker et al. (1968), a simple relationship could be developed between the critical temperature and chemical structure. This relationship does not require experimental data such as the normal boiling point. It was found that the critical temperature (Tc) is given by an expression containing m and the sum of delta-i, where m is the total number of atoms in the molecule and delta-i is a number whose value is obtained from a table of additive atomic, group, and structural constants.
A study was made on the stress relaxation behavior at 25 C of poly(methyl methacrylate) in uniaxial tension as a function of physical aging at both room temperature and 60 C. Test specimens were compression molded at 165 C, then quenched to room temperature and allowed to age for up to 30 days prior to testing. Stress relaxation curves measured after different aging times could be superposed to a single master curve for each aging temperature. Superposition was achieved by applying vertical and horizontal shifts. Hence, the shape of the response curves was not changed by aging. This is in accordance with observations made by Struik for tensile creep curves. Volume changes as a function of physical aging were also determined. Simple exponential relationships were observed between volume and both horizontal and vertical shifts. The horizontal shift implies a shift in the effective time scale caused by a change in free volume. The vertical shifts could be correlated with changes in Young's modulus caused by a change in density. For the range of aging studied, the response time scale varied over nearly two decades of log-time. For the same conditions modulus varied by 30 percent.