Search NASA⌕ Search

Engineering topics

Feldhausen, Thomas

Publications and source records attributed to Feldhausen, Thomas.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Mechanical and thermal behavior of additively manufactured Invar 36 using a laser hot wire hybrid DED process

Invar 36 alloy is a material of high interest in the composite tooling sector due to its low coefficient of thermal expansion. Current production of Invar 36 tooling using traditional manufacturing such as casting and forging is associated with long lead times due to a multitude of factors such as labor and component shortages, high material costs, foreign competition, and supply chain issues. An attractive alternate process is the use of an integrated 5-axis CNC hybrid Laser Hot Wire Deposition System (LHWD) for manufacturing invar molds. Here, the hybrid process provides a combination of the additive and subtractive technologies resulting in a synergistic platform for producing and repairing structures and molds. The main novelty and goal of this work is to study the properties of Invar deposited by a LHWD and to provide guidelines for the manufacture of parts using this process. In this study, the thermal expansion behavior of the manufactured specimens has been analyzed and related to its printing parameters and direction. Multiple specimens were extracted for mechanical, dilatometry and metallographic testing. A thermal IR recording of the printing process was also carried out to observe the thermal history of the produced parts to establish thermal influence on performance-property-processing relationship. The results of these tests show the advantage of LHWD technology for the manufacture of Invar alloy parts, as it presents similar thermal expansion behavior as those commercially available with minimal presence of precipitates and no macrostructural failures such as pores, cracks and lacks of fusion.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Phase Selection During Solidification and Solid-State Phase Transformations in an Al-10Ce-8Mn (wt pct) Alloy

In multicomponent Al-Ce alloys, and especially after additive manufacturing (AM), complex and metastable solidification microstructures are frequently observed. Here, in this research, the relationship between solidification conditions and phase selection are explored for an Al-10Ce-8Mn (wt pct) alloy using a systematic study of laser melting conditions. Three solidification modes were observed: primary Al 10 Mn 2 Ce; primary Al 20 Mn 2 Ce; and eutectic FCC Al + Al 20 Mn 2 Ce. These solidification modes were correlated to specific liquid-solid interface velocities using a simple thermal model, showing the change in primary solidification phase for low (< 6.8 × 10 −4 m/s), moderate (between 8.2 × 10 −4 and 5.9 × 10 −2 m/s) and high solidification velocities (> 6.2 x 10 −2 m/s) for the above three solidification microstructures, respectively. These results were rationalized by using interface response function (IRF) theory to describe the solidification undercooling for the possible primary intermetallic phases. The implication of the local phase selection from differing solidification conditions is summarized by a comparison of hardness which demonstrates the potential variance of Vickers hardness from 101 to 242 (VHV) by changing the laser velocity from 1 to 83 mm/s. Interestingly, on heat treatment at 400°C, the decomposition pathways of the solidification microstructure and hardness were also found to be different, thereby opening multiple pathways for spatial microstructure and property control within AM components.

Sisco, Kevin↗
DOE OSTI2024

Process parameter translation strategies for variable directed energy deposition spot size using 316L, copper, and Inconel 625

Directed energy deposition (DED) is a form of additive manufacturing available across a variety of laser spot diameter values, often referred to as spot sizes. However, there is no method to easily transfer process parameters across discrete spot sizes, leading to DED process parameters that are equipment specific and not widely applicable. In this study, a strategy is proposed and investigated for five spot sizes that keep the areal energy density constant while varying power, feed rate, and powder flow during the deposition of 316L stainless steel. An assessment of trends in hardness and microstructure is possible due to the novel production of components of a single material across several spot sizes using a single nozzle on a single DED system. The proposed strategy was used to nullify the hardness drop during functional grading of Inconel 625 and pure copper, enabling fabrication of multi-material sample that does not compromise desirable properties. This application shows the value in establishing more efficient process parameter development and understanding spot size influences on geometric and material property flexibility, to enable a more diverse powder-based DED design space and to increase the industry adoption of DED systems.

316L↗
DOE OSTI2024

Influence of printing parameters on the mechanical behavior of 3D-printed SS316L parts manufactured using laser hot wire directed energy deposition

Hybrid manufacturing combines the simultaneous benefits of additive manufacturing (complex geometries, part consolidation, and mass customization) with the advantages of subtractive manufacturing (superior surface finish and enhanced dimensional accuracies) by integrating a suite of complementary traditional processes into a base platform of additive manufacturing. The use of hybrid technology has grown in recent years given its capabilities on repairing metallic structures, producing parts with conformal cooling features, and manufacturing functionally graded products. These kinds of capabilities are of great interest to the medical implant, energy, automotive, maritime, and aerospace industry sectors, among many other fields. This work investigated the mechanical properties of stainless steel (SS) 316L as a function of different tool paths strategies using an integrated 5-axis CNC hybrid Mazak system with a laser hot wire deposition system (LHWDS). This study includes the evaluation of different printing parameters and their impact on the quality of the printed bead as well as the incorporation of a structure–property material relationship based on the mechanical performance of the manufactured coupons.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hybrid additive manufacturing of AISI 316L via asynchronous powder and hot-wire laser directed energy deposition

Hybrid Additive Manufacturing (AM) offers a way to leverage the advantages of different AM technologies, enabling the efficient production of sizeable parts without compromising material properties or geometric complexity capabilities. This study presents an asynchronous hybrid Directed Energy Deposition (DED) strategy employing laser powder DED and laser hot-wire DED. AISI 316L parts comprising multiple powder and wire segments were fabricated with optional machining on AISI 316L substrates to investigate how quality is impacted by (i) alternative process sequences (laser powder DED followed by laser hot-wire DED and vice versa), (ii) machined vs. as-printed interfacial conditions, and (iii) material deposition on top vs. alongside previously built segments. Optical microscopy, X-ray computed tomography, and Vickers hardness were used to characterize the morphology and microstructure of the parts, localized porosity and lack of fusion defects, bulk density, and mechanical properties. Interfacial machining was necessary for dimensional control but promoted lack of fusion voids, resulting in a 99.71 ± 0.01% dense part. As-printed interfaces resulted in a denser part (99.82 ± 0.02%) at the expense of dimensional accuracy. The hardness of the parts with as-printed and machined interfaces was 196 ± 0.37 HV and 192 ± 0.40 HV, respectively, compared to 156 ± 1.4 HV for the substrate. Depositing powder alongside or on top of wire sections resulted in interfaces with a hardness of 217 ± 2.2 HV, compared to 185 ± 3.4 HV for the wire-powder interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hybrid metal additive/subtractive machine tools and applications

Additive manufacturing creates parts by depositing a preform, typically layer by layer. Subtractive manufacturing involves removing material from a preform to create parts. Hybrid machine tools combine both additive and subtractive processes in the same workspace. They can be used to create parts that meet functional tolerance and surface finish requirements, or to create features that are difficult to produce using additive or subtractive processes alone. Here, this paper describes hybrid metal additive/subtractive machine tools. It covers design considerations, sensors and controls, process management, programming and software, and the impact on the design space. It also identifies future research challenges.

42 ENGINEERING↗
DOE OSTI2024

Coaxial color channel focus evaluation to estimate standoff height in directed energy deposition additive manufacturing

Directed energy deposition (DED) is an additive manufacturing process that is being rapidly adopted by industry and is well suited for the fabrication of complex components in a variety of metal alloys. In laser cladding systems such as DED, powder is blown in a stream to a metal substrate coincident with a laser necessary to deposit molten metal with 3D spatial control. The focus of both the laser and the powder stream are crucial, and best deposition occurs at a predetermined standoff height between the build surface and the print head. Generally, no monitoring of this distance is implemented in commercial DED systems. Due to potential over or under building, the standoff height often changes over time but tends to self-correct. However, inexpensive and minimally intrusive methods to identify optimal standoff are required to provide real-time control to maintain the optimal distance. The present work explores the quantification of the focus of the three-color channels of a coaxial camera to determine the standoff height. An experiment was performed in which a 254 mm wall is built and the standoff height, initially 5.0 mm below the optimal position, was then intentionally increased every 25.4 mm of wall length by an amount of 1.0 mm to a final position 7.0 mm above optimal. Computer vision is demonstrated to monitor the amount of focus in each color band and estimate standoff distance. Finally, a response can be calculated in under 40 ms using simple hardware and can work in most laser-based DED systems.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure manipulation via machining and heat treatments in hybrid manufacturing of 316L stainless steel

Hybrid manufacturing combines additive and subtractive (machining) processes in a single platform to reduce the total time to fabricate a component in its final form. Here we show that if sufficient plastic deformation can be imparted to the material during machining, recrystallization can be triggered during post-fabrication heat treatment. This can enable highly localized microstructure control. Additionally, we show that stainless steel 316L, when machined without coolant accumulates significant plastic strain compared to when machined with coolant that results in faster recrystallization kinetics during heat treatment. These effects are limited to the surface while the bulk microstructure remains unaffected.

316L stainless steel↗
DOE OSTI2024

Leveraging Additive Manufacturing to Fabricate High Temperature Alloys With Co-Designed Mechanical Properties and Environmental Resistance

A paradigm shift in the traditional sequential design approaches is critically essential to create application-specific hierarchical and multifunctional materials with superior long-term performance for next-generation energy technologies involving extreme environments. In the current work, we aim to leverage the flexibility and geometric/compositional complexity offered by additive manufacturing to demonstrate this new approach by codesigning a compositionally graded Ni-based alloy for molten salts\sCO 2 heat exchangers to enable mitigation of environmental degradation of surfaces exposed to molten halide salts, while simultaneously suppressing the consequent deterioration in mechanical stability. Further, thermokinetic modeling describing the underlying physics of thermally- and environmentally induced spatiotemporal compositional and microstructural evolution will be employed to predict the parameter space of material deposition processes and precisely identify the required composition gradient. Preliminary corrosion and mechanical testing of the dual material demonstrated the potential of the material to replace existing solid solution strengthened materials for this application.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The g-code file

The slicing process for additive manufacturing (AM) involves many steps, including slicing the object to be printed and fitting toolpaths to each resulting layer. The toolpaths define the trajectories that the machine must follow during printing to construct the object. Once the slicing is complete and all toolpaths have been found and properly planned, this data must be transferred to the 3D printer in a way the printer can use to construct the object. This is achieved by exporting a file, usually a g-code file, from the slicing software. The g-code file is a text-based file that contains instructions for the machine, controlling the system and defining the motions for each toolpath. The file, which often contains thousands of lines of code, is mostly composed of numbers that command positions for axis motions. This chapter will outline the contents of a g-code file, discuss various commands and their implementation, then provide example codes and files for object construction.

Roschli, Alex↗
DOE OSTI2024

Toolpath considerations for hybrid additive manufacturing

Hybrid additive manufacturing combines both additive and subtractive manufacturing processes to fabricate geometrically complex, dimensionally accurate parts that are difficult to make using either additive or subtractive manufacturing alone. Industrial applications for hybrid additive manufacturing include direct manufacturing (building whole parts), feature addition (adding onto existing parts), and remanufacturing or repair operations. To coordinate the additive and subtractive processes, computer-aided manufacturing (CAM) software must generate distinct toolpaths for each process. Each application requires different considerations and inputs when generating the toolpaths. For example, when building a part with an internal cavity that would otherwise be unmanufacturable due to reach or access limitations, a CAM must determine which layer(s) of deposition are appropriate to machine to create the internal cavity. This chapter explores the area of toolpath generation for hybrid manufacturing by discussing the necessary considerations that are unique to a hybrid process.

Feldhausen, Thomas↗
DOE OSTI2024

Planar slicing for nonextrusion AM processes

Extrusion-based AM processes, including material extrusion and directed energy deposition, construct objects by continuously depositing a relatively small amount of molten feedstock to a specific location. Nonextrusion AM processes, on the other hand, tend to form each layer by linearly or areally projecting either energy onto a vat of photocurable liquid or a binding agent into a bed of loose powder. Such systems vary significantly from extrusion-based AM processes but do share similarities. The general approach to path planning is the same, but nonextrusion processes typically favor the use of bitmap representations, instead of polygons, for pathing computation and do not use a g-code file to command the printer. In this chapter, a high-level discussion of these differences will be covered.

Macdonald, Eric↗
DOE OSTI2024

Travels, optimizations, and ordering

With all the necessary build pathing in place from the preceding steps, the final task is to organize the build pathing via directionality, ordering, and connectivity. Directionality controls closed-loop pathing by deciding whether construction occurs clockwise or counterclockwise. Ordering determines whether construction occurs outside-in or inside-out, by manipulating what path types will be printed first. Connectivity links all the pathing together, which is achieved through the insertion of travels. Connectivity has numerous approaches, but only the most common will be addressed in this chapter. In addition to these manipulations, other considerations, such as spiral pathing and unique cases for infill, will be discussed.

Borish, Michael↗
DOE OSTI2024

Off-axis and nonplanar slicing

Traditionally, slicing processes have assumed a horizontal plane that moves up the Z axis to produce layers. However, through relatively straightforward modifications, this process can be extended to allow planar slicing at any angle and along any axis in a process referred to as off-axis slicing. Additionally, more advanced pathing solutions are moving away from planar approaches entirely by printing directly on non-flat surfaces. Both of these alternative approaches to slicing, as well as some common issues associated with them, are discussed in this chapter to provide a foundation for more advanced pathing solutions.

Borish, Michael↗
DOE OSTI2024

Toolpath considerations for 5-axis systems

There have been many studies that show how additive manufacturing (AM) has been able to improve the performance of a component, reduce manufacturing costs, or minimize lead times. As the adoption of AM significantly increased, so did the complexity of designs for AM. Many designs require advanced systems, and in response to this, there is an increasing number of systems now capable of additional degrees of motion. 5-axis systems, which include two rotary axes, are becoming more common in the additive manufacturing community. These systems are capable of depositing material on a nonplanar surface and lend themselves to many industrial applications, further extending the design space for AM. However, computer-aided manufacturing (CAM) for AM has been dominated by 3-axis slicing software that do not typically accomodate 5-axis motion. This chapter introduces 5-axis motion and presents the unique considerations that need to be accounted for when generating toolpath trajectories for 5-axis systems.

Feldhausen, Thomas↗
DOE OSTI2024

Mechanical systems and kinematics

Kinematics is the study of how motion is achieved without reference to the forces that create the motion. This includes the basic structures of all robotic systems, such as links and joints, as well as their mathematical representations. This chapter will provide a brief overview of the types of motion used in additive manufacturing (AM) systems, as well as the mathematical equations that govern them. Rotations are explained using both Euler rotations and quaternions. Combined rotation and translations are shown using homogeneous transform matrices. The robot Jacobian, which relates joint velocities to the end effector translational velocities, is explained with an example calculation. This section will give the reader the basic mathematical foundation in kinematics that is necessary to understand the mechanical underpinnings of path planning for AM systems.

Wang, Peter↗