Search NASA⌕ Search

Engineering topics

Gayle, Andrew J.

Publications and source records attributed to Gayle, Andrew J..

4 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Lamination of >21% Efficient Perovskite Solar Cells with Independent Process Control of Transport Layers and Interfaces

Transport layer and interface optimization is critical for improving the performance and stability of perovskite solar cells (PSCs) but is restricted by the conventional fabrication approach of sequential layer deposition. While the bottom transport layer is processed with minimum constraints, the narrow thermal and chemical stability window of the halide perovskite (HP) layer severely restricts the choice of top transport layer and its processing conditions. To overcome these limitations, we demonstrate lamination of HPs—where two transport layer-perovskite half-stacks are independently processed and diffusion-bonded at the HP-HP interface—as an alternative fabrication strategy that enables self-encapsulated solar cells. Power conversion efficiencies (PCE) of >21% are realized using cells that incorporate a novel transport layer combination along with dual-interface passivation via self-assembled monolayers, both of which are uniquely enabled by the lamination approach. This is the highest reported PCE for any laminated PSC encapsulated between glass substrates. We further show that this approach expands the processing window beyond traditional fabrication processes and is adaptable for different transport layer compositions. The laminated PSCs retained >75% of their initial PCE after 1000 h of 1-sun illumination at 40 °C in air using an all-inorganic transport layer configuration without additional encapsulation. Furthermore, a laminated 1 cm 2 device maintained a V oc of 1.16 V. Finally, the scalable lamination strategy in this study enables the implementation of new transport layers and interfacial engineering approaches for improving performance and stability.

14 SOLAR ENERGY↗
DOE OSTI2021

Transparent Refractory Aerogels for Efficient Spectral Control in High–Temperature Solar Power Generation

Although spectrally selective materials play a key role in existing and emerging solar thermal technologies, temperature-related degradation currently limits their use to below 700 °C in vacuum and even lower temperatures in air. Here a solar-transparent refractory aerogel that offers stable performance up to 800 °C in air is demonstrated, which is significantly greater than its silica counterpart. This improved stability is attributed to the formation of a refractory aluminum silicate phase, which is synthesized using a conformal single cycle of atomic layer deposition within the high-aspect-ratio pores of silica aerogels. Furthermore, based on direct heat loss measurements, the transparent refractory aerogel achieves a receiver efficiency of 75% at 100 suns and an absorber temperature of 700 °C, which is a 5% improvement over the state of the art. Transparent refractory aerogels may find widespread applicability in solar thermal technologies by enabling the use of lower-cost optical focusing systems and eliminating the need for highly evacuated receivers. In particular, a shift to higher operating temperatures while maintaining a high receiver efficiency can enable the use of advanced supercritical CO 2 power cycles and ultimately translate to an ≈10% (absolute) improvement in solar-to-electrical conversion efficiency relative to existing linear concentrating systems.

14 SOLAR ENERGY↗
DOE OSTI2021

Tunable Atomic Layer Deposition into Ultra-High-Aspect-Ratio (>60000:1) Aerogel Monoliths Enabled by Transport Modeling

Atomic layer deposition (ALD) modification of ultra-high-aspect-ratio structures (>10,000:1) is a powerful platform with applications in catalysis, filtration, and energy conversion. However, the deposition of conformal and tunable ALD coatings at these aspect ratios remains challenging, resulting in empirical tradeoffs between precursor utilization and reaction time. Here, we demonstrate tunable control of the ALD infiltration depth into an aerogel monolith (AM) and develop a reaction-diffusion model to accurately describe the coating process. Specifically, we investigate the ALD exposure time and precursor dose needed to conformally coat a silica AM with pore sizes of ~20 nm, a monolith thickness of ~2.5 mm, and aspect ratios exceeding 60,000:1. We demonstrate complete infiltration into the AM, which is quantified by elemental mapping. A reaction-diffusion model is developed, which accounts for multiple doses and precursor depletion in the ALD chamber during an exposure step. The experimentally validated model enables the prediction and tuning of infiltration depth into a tortuous, high-aspect-ratio structure such as an AM, allowing for the synthesis of rationally designed material architectures. Additionally, the model allows for co-optimization of the total deposition time and percentage of unreacted precursor, which are important for the manufacturability and sustainability of ALD processing. Lastly, we demonstrate that ultra-thin ALD Al 2 O 3 coatings can be used to stabilize silica AMs against structural degradation under high-temperature annealing conditions (700-800 °C), by limiting changes in surface area and monolith volume. As a result, this improved high-temperature stability has implications for numerous aerogel applications, including catalysis and thermal insulation.

14 SOLAR ENERGY↗