Search NASA⌕ Search

Engineering topics

Gerrit-Daniel Stich

Publications and source records attributed to Gerrit-Daniel Stich.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Numerical Study on the Aerodynamics of an Iced Airfoil With Scale-Resolving Simulations

Scale-resolving simulations of the NACA 23012 airfoil with horn ice accretion on the leading edge are conducted using the hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation (hybrid RANS/LES) and wall-modeled large-eddy simulation (WMLES) approaches implemented in the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework. Aerodynamic results at the Reynolds number of 1.8 million show good comparison with the experimental measurements at different angles of attack from pre-stall to post-stall regimes. The pressure plateaus caused by the flow separation and the recovery of pressure inside the separation bubble around the iced leading edge are well predicted with the scale-resolving simulations when sufficient grid resolution is used around the accreted ice. The unsteadiness of the turbulent flows around the iced airfoil is also examined through the turbulent kinetic energy with the Reynolds normal stress anisotropy. Kelvin–Helmholtz instability (KHI) arises at the shear layer triggered by the upper ice horn and leads to rapid laminar-to-turbulent transition over a large range of angle of attack. With the increase of the angle of attack, the region with high turbulence intensity induced by the unstable shear layer spreads quickly over the entire upper surface of the airfoil. The coherent KHI modes from the upper and lower ice horns are extracted using the spectral proper orthogonal decomposition (SPOD) technique. The SPOD modes extracted from the upper shear layer have large-scale variations in the spanwise direction and low-rank behavior where the energy of the leading SPOD mode at each Strouhal number of the KHI largely represents the total energy when the mode number in the spanwise direction is small.

ARMD↗
NASA NTRS2023

Numerical Study on the Aerodynamics of an Iced Airfoil With Scale-Resolving Simulations

Scale-resolving simulations of the NACA 23012 airfoil with horn ice accretion on the leading edge are conducted using the hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation (hybrid RANS/LES) and wall-modeled large-eddy simulation (WMLES) approaches implemented in the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework. Aerodynamic results at the Reynolds number of 1.8 million show good comparison with the experimental measurements at different angles of attack from pre-stall to post-stall regimes. The pressure plateaus caused by the flow separation and the recovery of pressure inside the separation bubble around the iced leading edge are well predicted with the scale-resolving simulations when sufficient grid resolution is used around the accreted ice. The unsteadiness of the turbulent flows around the iced airfoil is also examined through the turbulent kinetic energy with the Reynolds normal stress anisotropy. Kelvin–Helmholtz instability (KHI) arises at the shear layer triggered by the upper ice horn and leads to rapid laminar-to-turbulent transition over a large range of angle of attack. With the increase of the angle of attack, the region with high turbulence intensity induced by the unstable shear layer spreads quickly over the entire upper surface of the airfoil. The coherent KHI modes from the upper and lower ice horns are extracted using the spectral proper orthogonal decomposition (SPOD) technique. The SPOD modes extracted from the upper shear layer have large-scale variations in the spanwise direction and low-rank behavior where the energy of the leading SPOD mode at each Strouhal number of the KHI largely represents the total energy when the mode number in the spanwise direction is small.

ARMD↗
NASA NTRS2023

Fan Noise Predictions of the NASA Source Diagnostic Test Using Unsteady Simulations with LAVA Part I: Near-Field Aerodynamics and Turbulence

A sliding mesh technique within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework is validated using the experimental dataset collected as part of the NASA Source Diagnostic Test (SDT) campaign. Two modeling approaches are explored: the unsteady Reynolds-Averaged Navier Stokes (URANS) with Spalart-Allmaras (SA) turbulence model closure, and a hybrid Reynolds-Averaged Navier Stokes/Large Eddy Simulation (RANS/LES) paradigm employing a Zonal Detached Eddy Simulation (ZDES) closure with enhanced shielding protection. Fan stage performance metrics, aerodynamic quantities and turbulent flow structures are analyzed in this work. Initial studies focusing on grid and time-step sensitivity are presented. Sensitivity to different variants of the SA turbulence model is analyzed, supporting the use of the baseline SA model in the production runs. Two conditions are analyzed in detail using URANS and hybrid RANS/LES (HRLES). Mean flow quantities are well-captured by both methods in the low-speed (approach) regime. While URANS misses all the upstream-propagating noise in the inlet due to the rotor-locked tones being evanescent in nature at subsonic fan tip speeds, HRLES captures this broadband component in its pressure field. At the high-speed (sideline) condition, URANS shows better agreement with the SDT data than HRLES in the interstage flow-field. In this regime, URANS captures the tonal content propagating through the inlet, since the tones are now cut-on. Both methods are suitable to capture fan stage performance metrics and mean flow quantities, but only HRLES is able to resolve the fine turbulent structures responsible for broadband noise. The results support the use of the sliding mesh technique implemented in this work for future turbomachinery applications within the LAVA solver framework.

AATT↗
NASA NTRS2023

Fan Noise Predictions of the NASA Source Diagnostic Test Using Unsteady Simulations with LAVA Part I: Near-Field Aerodynamics and Turbulence

A sliding mesh technique within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework is validated using the experimental dataset collected as part of the NASA Source Diagnostic Test (SDT) campaign. Two modeling approaches are explored: the unsteady Reynolds-Averaged Navier Stokes (URANS) with Spalart-Allmaras (SA) turbulence model closure, and a hybrid Reynolds-Averaged Navier Stokes/Large Eddy Simulation (RANS/LES) paradigm employing a Zonal Detached Eddy Simulation (ZDES) closure with enhanced shielding protection. Fan stage performance metrics, aerodynamic quantities and turbulent flow structures are analyzed in this work. Initial studies focusing on grid and time-step sensitivity are presented. Sensitivity to different variants of the SA turbulence model is analyzed, supporting the use of the baseline SA model in the production runs. Two conditions are analyzed in detail using URANS and hybrid RANS/LES (HRLES). Mean flow quantities are well-captured by both methods in the low-speed (approach) regime. While URANS misses all the upstream-propagating noise in the inlet due to the rotor-locked tones being evanescent in nature at subsonic fan tip speeds, HRLES captures this broadband component in its pressure field. At the high-speed (sideline) condition, URANS shows better agreement with the SDT data than HRLES in the interstage flow-field. In this regime, URANS captures the tonal content propagating through the inlet, since the tones are now cut-on. Both methods are suitable to capture fan stage performance metrics and mean flow quantities, but only HRLES is able to resolve the fine turbulent structures responsible for broadband noise. The results support the use of the sliding mesh technique implemented in this work for future turbomachinery applications within the LAVA solver framework.

AATT↗
NASA NTRSDate not supplied

Scale resolving simulations of the NASA Juncture Flow Model using the LAVA solver

Two distinct simulation methodologies: Delayed Detached Eddy Simulation (DDES) and stress based Wall-modelled Large Eddy Simulation (WMLES) are evaluated using structured overset curvilinear grids for the NASA juncture flow model. While both methodologies are shown to mitigate the primary shortcomings of steady state Reynolds Averaged Navier Stokes(RANS) simulations, several unresolved aspects are identified. Strong sensitivity to RANS-typegrid refinement is observed in the DDES with a substantial deterioration of the solution quality with increasing spatial resolution associated with deficiencies in the shielding function. Mean profiles for attached boundary layers on the fuselage show spurious inflections suggesting modelled stress depletion on finer grids. Lower numerical dissipation in terms of spatial discretization and time step size is seen to improve the solution quality, and the advantage of using RC and QCR2000 corrections in the underlying RANS closure is demonstrated for DDES on RANS-type meshes. Equilibrium Wall-Modelled LES used grids that resolved the tripping dots over the fuselage nose and the wing leading edge, consistent with the experiment setup. These simulations resulted in a cost-competitive approach compared to DDES on RANS-type grids. Although the agreement between WMLES predictions of first and second order single point statistics with experimental measurements is promising, a fundamental shortcoming is noted in terms of an overshoot in streamwise momentum in corner regions of the wing-fuselage juncture. This excess momentum subsequently delays the onset of separation,thereby resulting in an underprediction in length of the separation bubble. Some quantitative sensitivity to numerical discretization is observed; lowering of numerical dissipation shows better agreement with the experiment.

T^3↗
NASA NTRSDate not supplied

Jet Noise Prediction for Chevron Nozzle Flows with Wall-Modeled Large-Eddy Simulation

This paper presents results from ongoing research on jet noise prediction with wall-modeled large eddy simulations (WMLES) performed with the LAVA computational framework. In particular the focus of this study is on mixing enhancements from a single stream chevron nozzle at Reynolds number of 1×10(exp 6). Although the concept of chevron nozzles to reduce jet noise is not new, our understanding of its impact on the overall noise is still not well understood. As a first step towards predicting noise reduction due to mixing enhancement concepts from first principles with WMLES, we simulate the noise generated by a single stream chevron nozzle SMC001 as well as its equivalent axisymmetric round jet nozzle SMC000. Detailed comparisons are made with a dedicated experiment conducted at NASA’s Glenn Research Center and good agreement was achieved. Two different approaches to introduce a turbulent boundary layer were compared but show no major impact on the results. This is especially important given future work were multi-stream nozzles are considered and extended costs of resolving the internal BL would have a bigger cost impact. A permeable Ffowcs Williams Hawkings (FWH) surface enclosing the jet is used to predict far-field noise from the simulated flow-field and excellent comparison to microphone array measurements is achieved within the resolved frequency band. Sensitivity of far-field noise predictions to grid resolution is systematically documented. Near-field comparisons to PIV data shows great agreement for both velocity and normal stresses, however a systematic TKE overshoot at the nozzle exit is seen in the shear-layer. The paper shows a cost reduction of an order of magnitude compared to an earlier study of this configuration due to algorithmic and software improvements and demonstrates that WMLES can be used as a cost-competitive approach for jet noise predictions.

CST↗
NASA NTRSDate not supplied

Transonic Lift and Drag Predictions using Wall Modelled Large Eddy Simulations

Wall-modelled Large Eddy Simulations (WMLES) of the NASA Common Research Model (CRM) at transonic conditions and various angles of attacks leading up to and including shock-induced flow separation are performed using the LAVA computational framework. The simulations are shown to accurately predict the lift curve slope and the onset of separation characterized by the break in the pitching moment. Furthermore, careful assessment of skin-friction drag at cruise condition and its subsequent decrease with increasing angles of attack are shown to be in agreement with viscous sublayer resolving Reynolds Averaged Navier Stokes(RANS) simulations. The small differences between WMLES and RANS appear to be of the same order as differences seen between two RANS models at the cruise-point. Some sensitivity is observed to the coefficient used in the subgrid scale model, although this can be reconciled by noting the low chord- and shock-incidence Reynolds numbers (Rex≈106) seen in the outboard regions of the wing, along with the uncertainties associated with tripping and the numerical transition that occurs near the leading edge. Among the primary drawbacks seen in the WMLES predictions is the subdued increase in wave-drag with increasing angle-of-attack and the shock intensity when compared with experimental data. Preliminary assessment suggests that additional span- and stream-wise grid resolution is likely needed in mid- and out-board portions of the wing to better resolve the shock-induced separated flow and to further investigate prediction accuracy of unsteady temporal characteristics of the problem.

ARMD↗
NASA NTRSDate not supplied

High-Lift Common Research Model: RANS, HRLES and WMLES Perspectives for CLmax Prediction Using LAVA

A unified assessment of three turbulence treatments: Reynolds Averaged Navier-Stokes(RANS), Hybrid RANS/LES (HRLES) and Equilibrium Wall-Modelled Large Eddy Simulation(WMLES) is presented for the High-Lift Common Research Model (CRM-HL). For the free-air configuration, steady-state RANS simulations show very accurate drag polar predictions in the low-𝛼linear regime. However, strong grid sensitivity is reported near the maximum lift-state(𝐶𝐿max), with finer-grids showing larger errors and predicting erroneous flow topologies on the wing. Our RANS simulations show that several corrections for the Spalart-Allmaras (SA)turbulence model widely used in the community lead to more erroneous results compared to the baseline closure, without exception. Both scale-resolving methods (HRLES and WMLES)address these drawbacks and predict an outboard separation pattern on the main element that is in good agreement with the oil flow photographs taken from the QinetiQ wind tunnel experiments, when LES-appropriate grids and numerical discretizations are used. While RANS simulations with the baseline SA closure do not show any wing-root separation post𝐶𝐿max, both HRLES and WMLES show onset of corner flow separation with varying degrees of progression, along with a weak pitch break in the wing-contribution of the overall pitching moment. This post-𝐶𝐿max pitch break seen in the free-air simulations is weaker than the break observed in experiments, with a weaker break reported in WMLES for each iteration of grid-refinement. In-tunnel simulations using both SA-baseline RANS and WMLES show a much stronger post-𝐶𝐿max break with the WMLES predictions showing excellent agreement with the experiment in terms of both the flow-topology observed and the pressure-coefficients at various spanwise stations. Sensitivity to the tunnel wall boundary layer is characterized via comparisons between viscous and inviscid treatments for the tunnel walls. WMLES predictions show moderate sensitivity at the predicted inboard flow-state at 𝐶𝐿max along with the progression towards a post-𝐶𝐿max stall; however, this stalled state at 𝛼≈20◦(inside the tunnel) obtained with both tunnel wall treatments appears to be largely identical.

TTT↗
NASA NTRSDate not supplied

Wall Modeled Large Eddy Simulations for NASA’s Jet Noise Consensus Database of Single-Flow, Round, Convergent Jets

A campaign of wall-modeled large-eddy simulations (WMLES) using structured curvilinear overlapping grids has been performed with the Launch Ascent and Vehicle Aerodynamics(LAVA) computational fluid dynamics (CFD) software to predict jet noise for single-stream axisymmetric round jets. The simulations address the new Prediction Uncertainty Reduction(PUR) technical challenge within the context of NASA’s Commercial Supersonic Technology(CST) project. The goal of PUR is to quantify and reduce uncertainties from scale-resolving simulations to assess noise characteristics of next generation quiet supersonic commercial jets during takeoff and landing conditions where the noise from the exhaust jet dominates. The focus of this effort is to generate a simulation database for single-stream axisymmetric round nozzles at several conditions both for static (no ambient co-flow), which is the focus of this article, and in-flight (flight stream co-flow) conditions, which are beyond the current scope. Nine different flow conditions ranging in jet exit Mach number from 0.38 to 1.0 with nozzle temperature ratios (NTR) from 0.84 to 2.7 have been conducted. Details of the structured overset grids, numerical discretization and wall-model are provided. Near-field comparisons to PIV data show great agreement for both velocity and normal stresses, however a systematic TKE overshoot at the nozzle exit is seen in the lip line shear-layer. A permeable Ffowcs Williams Hawkings (FWH) surface, enclosing the jet, is used to predict far-field noise from the simulated flow-field. Comparison of CFD predictions to microphone array measurements demonstrate excellent agreement within the resolved frequency range. A systematic under-prediction of far-aft observer angles larger than 150 degrees has been observed across all simulations. We achieved a cost reduction of an order of magnitude for these WMLES compared to an earlier study of this configuration due to algorithmic and software improvements. The accuracy of the results and short turnaround time demonstrate that WMLES within the LAVA framework is a cost-effective approach for jet noise predictions that could soon be incorporated into the design cycle of jet noise reduction technologies.

CST↗