Search NASA⌕ Search

Engineering topics

Giudicotti, L

Publications and source records attributed to Giudicotti, L.

Impurities removal by laser blow-off from in-vacuum optical surfaces on RFX-mod experiment

An in situ window cleaning system by laser blow-off through optical fiber has been developed on the basis of a feasibility study previously presented. The beam generated by a Q-switched Nd:YAG laser is launched in a vacuum box into a high damage threshold optical fiber through a lens. The fiber output is focused on the impurities-coated surface of a vacuum window exposed to the plasma of the RFX-mod experiment, and it is remotely controlled with an xy motion system to scan the entire surface. We first investigate the energy density threshold necessary to ablate the deposited impurity substrate on removed dirty windows: above threshold, a single laser pulse recovers {approx}95% of the window transmission before its exposure to the plasma, while below it the efficiency of the cleaning process is too poor. The system so conceived was then used to clean the three collection windows of the Main Thomson scattering diagnostic on RFX-mod. We also present results obtained applying the same technique to the SiO-protected Al mirror used for the Z{sub eff} diagnostic: an energy threshold for efficient impurity removal without mirror damage is first identified, then ablation tests are executed and analyzed in terms of recovered reflectivity. The SIMS technique is used both with windows and mirror to study the composition of surfaces before and after the ablation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Systematic comparison between line integrated densities measured with interferometry and polarimetry at JET

A systematic comparison between the line integrated electron density derived from interferometry and polarimetry at JET has been carried out. For the first time the reliability of the measurements of the Cotton-Mouton effect has been analyzed for a wide range of main plasma parameters and the possibility to evaluate the electron density directly from polarimetric data has been studied. The purpose of this work is to recover the interferometric data with the density derived from the measured Cotton-Mouton effect, when the fringe jump phenomena occur. The results show that the difference between the line integrated electron density from interferometry and polarimetry is with one fringe (1.143x10{sup 19} m{sup -2}) for more than 90% of the cases. It is possible to consider polarimetry as a satisfactory alternative method to interferometry to measure the electron density and it could be used to recover interferometric signal when a fringe jumps occurs, preventing difficulties for the real-time control of many experiments at the JET machine.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

In situ window cleaning by laser blowoff through optical fiber

The feasibility of a window cleaning system based on the laser blowoff technique is investigated to remove the impurity deposition on vacuum windows of the modified reversed field experiment fusion device. The laser pulse is sent to the window through a fused silica fiber optic ({phi}=1 mm), then focused on its internal surface, single shot ablating up to {approx}5 mm{sup 2} of the impurity layer; the focused pulse is scanned across the window to clean its entire surface. The composition of the deposited layer is studied through the secondary ion mass spectrometry and profilometry techniques. Effectiveness of cleaning is analyzed in terms of quality of the cleaned spot, its dimension, repetition rate of the laser, and its wavelength. The energy damage threshold of the fiber optic is also investigated. Three different lasers (microjoule Nd:YAG, Nd:YLF, and ruby) are first tested directly on the window; then only the ruby laser beam is propagated through an optical fiber and tested.

36 MATERIALS SCIENCE↗

Enhancement of the JET edge LIDAR Thomson scattering diagnostic with ultrafast detectors

The edge light detection and ranging (LIDAR) Thomson scattering diagnostic at the Joint European Torus fusion experiment uses a 3 J ruby laser to measure the electron density and temperature profile at the plasma edge. The original system used a 1 GHz digitizer and detectors with response times of {approx_equal}650 ps and effective quantum efficiencies <7%. This system has recently been enhanced with the installation of a new 8 GHz digitizer and four new ultrafast GaAsP microchannel plate photomultiplier tube detectors with response times of <300 ps and effective quantum efficiencies in the range of {approx}13%-20% (averaged over {lambda}=500-700 nm). This upgrade has enabled the spatial resolution to be reduced to {approx}6.3 cm along the laser line of sight for a laser pulse of 300 ps full width at half maximum, which is close to the requirements for the ITER core LIDAR. Performance analysis shows that the new system will have an effective spatial resolution of up to 1 cm in the magnetic midplane via magnetic flux surface mapping.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ITER LIDAR performance analysis

The core LIDAR Thomson scattering for ITER is specified for core profile measurements with a spatial resolution of 7 cm (a/30) for the range of 500 eV<T{sub e}<40 keV and n{sub e}>3x10{sup 19} m{sup -3} at an accuracy of <10% for T{sub e}. These specifications are verified using a full profile Monte Carlo simulation code. In the simulations it is assumed that the input transmission is 50% and the collection transmission is 10% for {lambda}=300-1200 nm and F/=6-17. A crucial design decision lies on the choice of laser and detector combination. It is evaluated that the system can meet its spatial and accuracy specifications for higher temperatures of T{sub e}>5 keV with a combination of a neodymium-doped yttrium aluminum garnet (Nd:YAG) laser ({lambda}{sub 0}=1064 nm, {delta}{lambda}<1 nm, 5 J, and {delta}t{sub FWHM}=250 ps, 5-10 Hz) and S20, GaAs, and GaAsP microchannel plate photomultipliers ({delta}t{sub FWHM}<300 ps, effective quantum efficiency, EQE=3%-4%, and D=18 mm). In order to reach the required T{sub e} of 500 eV with Nd:YAG first harmonic, this choice requires a development of fast near infrared detectors.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗