Search NASA⌕ Search

Engineering topics

Greenaway, Ann

Publications and source records attributed to Greenaway, Ann.

Investigation of Off-Stoichiometry in Ternary Nitrides by EDS and HRTEM

We demonstrate an inverted metamorphic multijunction (IMM) photovoltaic cell comprising lattice-mismatched 1.2 eV AlGaInAs and 1.0 eV GaInAs junctions optimized for high-temperature thermophotovoltaic (TPV) applications. This device differs from traditional IMM solar cells because the mismatched junctions are grown at a single lattice constant. This architecture enables removal of the compositionally graded buffer which otherwise filters light from the junctions below and absorbs sub-bandgap light via free-carrier absorption. Sub-bandgap absorption dramatically reduces the efficiency of TPV systems using high reflectivity cells to enable bandedge spectrum filtering. Three components required development to enable this device: 1) a lattice-mismatched 1.2 eV AlGaInAs junction, 2) a metamorphic contact layer grown after the graded buffer, and 3) a transparent tunnel junction that sits in front of the 1.0 eV GaInAs junction. Growth conditions that minimize oxygen defect incorporation maximize AlGaInAs cell quality, enabling a 0.41 V bandgap open circuit voltage offset at 22 mA/cm2 under AM1.5D. A mismatched GaInAs:Se layer is developed as a low resistance contact. Lastly we develop a GaAsSb:C/GaInP:Se tunnel junction suitable for high-power densities with more transparency than the GaAsSb:C/GaInP:Se structure used in past IMM cells. We characterize the tandem device under a high-intensity spectrum that approximates the emission from a 2150 °C blackbody radiator and deduce a projected ideal TPV efficiency of 39.9% at ~30% of the blackbody irradiance, and 36% ideal TPV efficiency under the full 118 W/cm2 irradiance. Improvements to the back-surface reflectivity and series resistance are expected to increase the ideal TPV efficiency well above 40%.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Tin Nitride Atomic Layer Deposition Using N2H4

There is substantial lag in the development of atomic layer deposition (ALD) processes for nitrides compared to the high-quality, conformal oxides for which ALD has become the standard. A major factor in this disparity is the ready availability of highly reactive oxygen sources (mainly H2O, O2, and H2O2). High-energy nitrogen precursors are similarly required for the efficient incorporation of nitrogen in a film. Ammonia has often been used in conjunction with metal chlorides but requires relatively high temperatures for thermal ALD. Plasma-enhanced ALD can utilize molecular nitrogen as a precursor but can reduce film conformality on complex supports and damage the underlying substrate. Hydrazine (N2H4) is an alternative precursor which has been rarely explored for the fabrication of nitrides in ALD, but which is experiencing a surge in popularity due to its high reactivity, which enables the deposition of nitrides as-yet undemonstrated by ALD.(1) The added reactivity and volatility of liquid hydrazine may enable new reaction mechanisms, lower deposition temperatures, and conformality for high aspect ratio applications. Sn3N4 is a metastable semiconductor which shares a crystal structure with its analog, Si3N4; unlike Si3N4, Sn3N4 has only recently been grown by ALD,(2) being synthesized much more often through reactive sputtering.(3) As a binary, Sn3N4 has applications as a battery anode material, for photoelectrochemistry, and optoelectronic devices. We will report progress on the deposition of SnxNy films from tetrakis(dimethylamido) tin (TDMASn) and N2H4. Growth per cycle of this material (determined by x-ray reflectivity) is 0.4 A at 200 C, similar to the sole report of Sn3N4 from PE-ALD,(2) despite films being substantially Sn-rich. Identification of ALD growth window and self-limiting deposition characteristics are underway; initial testing indicates a competing chemical vapor deposition process which can be eliminated with adequate tuning of pulse/purge characteristics. A comparison of film conductivity and optical absorption at different growth temperatures will be presented. General issues of N2H4 purity and routes to prevent or control oxynitride formation will be discussed. (1) Du, L., et al. The First Atomic Layer Deposition Process for FexN Films. Chem. Comm., 2019, ASAP. DOI: 10.1039/C8CC10175B. (2) Stewart, D. M., et al. Tin Oxynitride Anodes by Atomic Layer Deposition for Solid-State Batteries. Chem. Mater. 2018, 30, 2526-34. (3) Caskey, C. M., et al. Semiconducting Properties of Spinel Tin Nitride and Other IV3N4 Polymorphs. J. Mater. Chem. C 2015, 3, 1389-96.

14 SOLAR ENERGY↗

GaAs thin films and methods of making and using the same

Disclosed herein are embodiments of methods for making GaAs thin films, such as photovoltaic GaAs thin films. The methods disclosed herein utilize sources, precursors, and reagents that do not produce (or require) toxic gas and that are readily available and relatively low in cost. In some embodiments, the methods are readily scalable for industrial applications and can provide GaAs thin films having properties that are at least comparable to or potentially superior to GaAs films obtained from conventional methods.

30 DIRECT ENERGY CONVERSION↗

Final Report: Vapor Transport Deposition for Thin Film III-V Photovoltaics

Silicon, the dominant photovoltaic (PV) technology, is reaching its fundamental performance limits as a single absorber/junction technology. Higher efficiency devices are needed to reduce cost further because the balance of systems account for about two-thirds of the overall cost of the solar electricity. III-V semiconductors such as GaAs are used to make the highest-efficiency photovoltaic devices, but the costs of manufacture are much too high for non-concentrated terrestrial applications. The cost of III-V’s is driven by two factors: (1) metal-organic chemical vapor deposition (MOCVD), the dominant growth technology, employs expensive, toxic and pyrophoric gas-phase precursors, and (2) the growth substrates conventionally required for high-performance devices are monocrystalline III-V wafers. The primary goal of this project was to show that close-spaced vapor transport (CSVT), using water vapor as a transport agent, is a scalable deposition technology for growing low-cost epitaxial III-V photovoltaic devices. The secondary goal was to integrate those devices on Si substrates for high-efficiency tandem applications using interface nanopatterning to address the lattice mismatch. In the first task, we developed a CSVT process that used only safe solid-source powder precursors to grow epitaxial GaAs with controlled n and p doping and mobilities/lifetimes similar to that obtainable via MOCVD. Using photoelectrochemical characterization, we showed that the best material had near unity internal quantum efficiency for carrier collection and minority carrier diffusions lengths in of ~ 8 μm, suitable for PV devices with >25% efficiency. In the second task we developed the first pn junction photovoltaics using CSVT and showed unpassivated structures with open circuit photovoltages > 915 mV and internal quantum efficiencies >0.9. We also characterized morphological and electrical defects and identified routes to reduce those defects. In task three we grew epitaxial ternary GaAsxP 1-x and In 0.5 Ga 0.5 P alloys, with composition set by the ratio of GaAs/GaP or InP/GaP mixed as the source powder. GaAs 0.3 P 0.7 has the appropriate bandgap to serve as a top cell on Si and In 0.5 Ga 0.5 P is near the composition used as a surface passivation layer on GaAs pn junction photovoltaics. In the final task we demonstrated III-V selective area epitaxy using CSVT as a first step toward the growth of III-V micro- or nanostructures for an integrated tandem solar cell on Si. We also found that direct epitaxial growth on Si appears to be impossible in the current H 2 O-CSVT reactor design, likely due to the formation of SiO x . This work sets the stage for targeted development of an improved CSVT process and for the scale up of the proof-of-concept work from a research to manufacturing-relevant platform. Replacing H 2 O as a transport agent with HCl would provide the ability to deposit directly on Si by avoiding oxide formation and to allow for the deposition of Al-containing alloys that would otherwise oxidize. Improved engineering design and implementation of an in-line multi-station CSVT would allow for direct deposition of device structures in a single system.

14 SOLAR ENERGY↗