Search NASA⌕ Search

DOE OSTI · 1547255

Tin Nitride Atomic Layer Deposition Using N2H4

Abstract

There is substantial lag in the development of atomic layer deposition (ALD) processes for nitrides compared to the high-quality, conformal oxides for which ALD has become the standard. A major factor in this disparity is the ready availability of highly reactive oxygen sources (mainly H2O, O2, and H2O2). High-energy nitrogen precursors are similarly required for the efficient incorporation of nitrogen in a film. Ammonia has often been used in conjunction with metal chlorides but requires relatively high temperatures for thermal ALD. Plasma-enhanced ALD can utilize molecular nitrogen as a precursor but can reduce film conformality on complex supports and damage the underlying substrate. Hydrazine (N2H4) is an alternative precursor which has been rarely explored for the fabrication of nitrides in ALD, but which is experiencing a surge in popularity due to its high reactivity, which enables the deposition of nitrides as-yet undemonstrated by ALD.(1) The added reactivity and volatility of liquid hydrazine may enable new reaction mechanisms, lower deposition temperatures, and conformality for high aspect ratio applications. Sn3N4 is a metastable semiconductor which shares a crystal structure with its analog, Si3N4; unlike Si3N4, Sn3N4 has only recently been grown by ALD,(2) being synthesized much more often through reactive sputtering.(3) As a binary, Sn3N4 has applications as a battery anode material, for photoelectrochemistry, and optoelectronic devices. We will report progress on the deposition of SnxNy films from tetrakis(dimethylamido) tin (TDMASn) and N2H4. Growth per cycle of this material (determined by x-ray reflectivity) is 0.4 A at 200 C, similar to the sole report of Sn3N4 from PE-ALD,(2) despite films being substantially Sn-rich. Identification of ALD growth window and self-limiting deposition characteristics are underway; initial testing indicates a competing chemical vapor deposition process which can be eliminated with adequate tuning of pulse/purge characteristics. A comparison of film conductivity and optical absorption at different growth temperatures will be presented. General issues of N2H4 purity and routes to prevent or control oxynitride formation will be discussed. (1) Du, L., et al. The First Atomic Layer Deposition Process for FexN Films. Chem. Comm., 2019, ASAP. DOI: 10.1039/C8CC10175B. (2) Stewart, D. M., et al. Tin Oxynitride Anodes by Atomic Layer Deposition for Solid-State Batteries. Chem. Mater. 2018, 30, 2526-34. (3) Caskey, C. M., et al. Semiconducting Properties of Spinel Tin Nitride and Other IV3N4 Polymorphs. J. Mater. Chem. C 2015, 3, 1389-96.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Greenaway, Ann, Shulda, Sarah, Link, Elisa M, Tamboli, Adele C, Christensen, Steven T. 2019-07-31. Tin Nitride Atomic Layer Deposition Using N2H4. https://searchnasa.com/record/osti%3A1547255/tin-nitride-atomic-layer-deposition-using-n2h4

Citations retain the original authors and DOI and include this site’s record URL. If this discovery service contributed to your research, you can also cite Search NASA by Indiciae: BibTeX · RIS.

KEEP EXPLORING

Related reports

Heliostat sizing methodology for concentrating solar thermal industrial process heat projects

This study presents a method to obtain a heliostat size that minimizes the levelized cost of heat (LCOH) of a heliostat-based concentrating solar thermal system for applications of solar heating for industrial processes at operating temperatures from 565 to 1550°C. The method extends prior work by embedding a routine for system design that obtains near-optimal subsystem sizes, increasing the fidelity of drive cost functions, and adding an optical performance model to supplement the previously developed cost models, which we update to reflect current pricing trends. An illustrative business case is developed for Daggett, California, targeting specified annual thermal energy outputs of 50 to 400 GWh th . Optical performance is modeled using verified estimates from the literature. A surrogate heliostat cost model, derived from commercial heliostat designs and scaled for production volume, installation, and operations and maintenance costs, is used to develop cost functions. Results show that heliostat size strongly affects the LCOH, producing a characteristic U-shaped trend with a robust near-optimal window of 7-20 m 2 ; the heliostat size producing the lowest project cost in our study grows slightly as the project size increases, and is reduced as the operating temperature increases. The findings in this study are consistent with the general trend of smaller heliostats being deployed at existing projects for high-temperature industrial process heat and reflect the significant reduction in power electronics and other per-heliostat costs. The methodology we propose is general and can be tailored to revised cost curves as the technology continues to evolve.

14 SOLAR ENERGY↗

A Sensitivity-driven Wide Area Protection (SWAP) Coordination Tool for High Penetration of Inverter-based Resources (IBR)

Traditionally, power system generation sources have been composed of synchronous generators, of which the fault current behavior is understood with minimal differences between generation size and types due to the physics of their construction. Present protection schemes and modeling methods are based upon these understood characteristics. Most renewable generation is composed of inverter-based resources (IBR), in which fault current is determined by switching control software and hardware limitations, each of which can vary between manufacturers and even between models of the same manufacturer. The resulting fault current is low in magnitude, low in negative-sequence current, unpredictable phase angles, and is a challenge to model. These characteristics also result in a challenge to traditional protection schemes and fault simulation software. To address several of these concerns, the project has the following goals: 1. Improve IBR models: Improve IBR models used in short circuit (SC) programs to accurately capture the response of IBRs at the bulk power system (BPS) level for fault and protection studies. 2. Develop automation tool: Develop an automation tool that allows engineers to identify protection coordination and sensitivity issues by performing SC and protection coordination studies in a high IBR-penetrated grid by applying variations to the IBR models, faults, contingencies, etc. 3. Develop schemes: Develop new protection mitigation solution schemes that complement the existing protection systems to ensure safe operation of the BPS with higher IBR penetration levels. The project team did not achieve this final goal, as the Department of Energy (DOE) stopped the project early due to changes in DOE funding priorities. The termination notice came at the beginning of the final project phase, while the team was identifying and beginning to investigate protection issues. It should be noted that the team discussed a 100% penetration scenario. However, this scenario would require the use of grid-forming IBR models that are not presently available. Since developing these models requires additional effort, the 100% penetration scenario was not pursued during this project. In the future, developing the methodology and models for the 100% scenario could benefit the industry.

14 SOLAR ENERGY↗

Technoeconomic Analysis Round Robin of a Retrofit of the Ivanpah Concentrating Solar Plant with a Molten-Salt System with Thermal Energy Storage

While the fidelity of technoeconomic analysis (TEA) models for concentrating solar thermal systems has improved in recent years, there is a lack of consensus on the specific inputs used to forecast performance of a newly built tower system due to a lack of validations and post-mortems available to the public. This effort is a joint initiative between multiple international organizations to validate and compare their TEA models. The specific case study is a proposed retrofit of one unit of the Ivanpah Solar Energy Generating System to include molten-salt storage, replacing the steam generation system with a molten-salt receiver, salt-to-steam heat exchanger train, and new balance of plant while keeping the existing steam turbine, solar field, and interconnection in place, using plant data for calibration. This manuscript discusses several of the agreed-upon assumptions for this study as well as a preliminary analysis from prior work that motivates the study.

14 SOLAR ENERGY↗