Engineering topics

Hicks, R. M.

Publications and source records attributed to Hicks, R. M..

At least 19 records

NASA NTRS1992

Practical design optimization of wing/body configurations using the Euler equations

The development of a practical method for the aerodynamic design of isolated wing and wing/body configurations is achieved through the coupling of existing computational fluid dynamics (CFD) analysis codes and a quasi-Newton numerical optimization method. The direct design method is generalized to treat three-dimensional aerodynamic optimization problems subject to inviscid, rotational, compressible flow conditions imposed by the Euler equations. The method couples either the FLO57 or the TEAM flow solver with a modified version of the QNMDIF numerical optimization algorithm. The method is applied, but is not limited, to supersonic design problems. A case study is presented illustrating the method's effectiveness in maximizing the lift-to-drag ratio, subject to a variety of constraints, of selected supersonic configurations at cruise conditions.

Reuther, J.↗

NASA NTRS1990

Euler and Potential Experiment/CFD Correlations for a Transport and Two Delta-Wing Configurations

A selection of successes and failures of Computational Fluid Dynamics (CFD) is discussed. Experiment/CFD correlations involving full potential and Euler computations of the aerodynamic characteristics of four commercial transport wings and two low aspect ratio, delta wing configurations are shown. The examples consist of experiment/CFD comparisons for aerodynamic forces, moments, and pressures. Navier-Stokes equations are not considered.

Hicks, R. M.↗

NASA NTRS1990

Euler and potential computational results for selected aerodynamic configurations

A selection of CFD successes and failures is evaluated, on the basis of experimental data/CFD result correlations involving full-potential and Euler computations of the aerodynamics of four commercial transport wings and two low aspect ratio delta wings. An effort is made to ascertain optimum values for grid density and distribution, artificial dissipation, Courant-Friedrichs-Lewy number, enthalphy damping, and a multigrid scheme for each flow condition and configuration analyzed. It is demonstrated that CFD solutions can assist the experimentalist prior to a test by indicating the locations of high pressure gradients and projecting test condition limitations due to balance design limits.

Hicks, R. M.↗

NASA NTRS1985

An evaluation of three helicopter rotor sections

Three helicopter rotor sections were tested in the NASA Ames Research Center 2- by 2-Foot Transonic Wind Tunnel over a Mach range from 0.2 to 0.88. The sections tested had maximum thickness/chord ratios of 0.078, 0.09, and 0.10. The thickest section was of early technology and had been tested previously in other wind tunnels. This section was included in the investigation to establish a basis for comparing the two thinner sections, which were of recent design. The results of the investigation showed that the pitching-moment characteristics for the three airfoil sections were acceptable. The drag divergence Mach numbers for the three sections were 0.80, 0.825, and 0.845 in order of decreasing thickness.

Hicks, R. M.↗

NASA NTRS1984

A recontoured, upper surface designed to increase the maximum lift coefficient of a modified NACA 65 (0.82) (9.9) airfoil section

A recontoured upper surface was designed to increase the maximum lift coefficient of a modified NACA 65 (0.82)(9.9) airfoil section which was tested at Mach numbers of 0.3 and 0.4 and Reynolds numbers of 2.3x10(6) and 4.3x10(6). The original 6-series section was tested for comparison with the recontoured section. The recontoured profile was found to have a higher maximum lift coefficient at all test conditions than the original airfoil. The recontoured airfoil showed less drag and nearly the same pitching moment characteristics as the original 6-series airfoil at all test conditions. The improvements found for the recontoured airfoil of the present study are similar to those found during previous investigations of recontoured 6-series airfoils with less camber.

Hicks, R. M.↗

NASA NTRS1982

An assessment of a modified potential flow code for calculating the effect of small geometric change on the pressure and forces of supercritical airfoils

Wind-tunnel test data for two closely related supercritical airfoils were compared with calculations obtained from a nonconservative, potential flow code over a Mach number range from 0.20 to 0.80. The potential flow code includes an iterated, integral boundary-layer correction. The theoretical pressure distributions correlated more closely with the experimental pressure distributions when the flow was entirely subsonic or subsonic with a small supersonic zone than when the flow contained a large supersonic zone. The predicted drag level was below the experimental values at nearly all test conditions and the difference in drag level for the two airfoils was not accurately predicted.

Hicks, R. M.↗

NASA NTRS1981

A comparison of theoretical and experimental pressure distributions for two advanced fighter wings

A comparison was made between experimental pressure distributions measured during testing of the Vought A-7 fighter and the theoretical predictions of four transonic potential flow codes. Isolated wind and three wing-body codes were used for comparison. All comparisons are for transonic Mach numbers and include both attached and separate flows. In general, the wing-body codes gave better agreement with the experiment than did the isolated wing code but, because of the greater complexity of the geometry, were found to be considerably more expensive and less reliable.

Haney, H. P.↗

NASA NTRS1981

Transonic wing design using potential-flow codes - Successes and failures

The state-of-the-art of transonic wing design by use of computer codes based on the potential flow-theory is presented. The capabilities and limitations of these codes are exemplified by several experiment-theory correlations, including an assessment of pressure distribution from isolated wing and wing-body codes. Computer codes using both conservative and nonconservative differencing schemes were used, and the effects of boundary-layer corrections were considered. Results showed that calculations from a full potential, isolated code correlate well with data from an isolated wing test, but may give poor predictions of the aerodynamic characteristics of some wing-body configurations. Boundary-layer correlations were found to have only moderate effects on experiment-theory correlation. Aeroelastic effects were considered important for high aspect ratio wings of low to moderate thickness, and viscous effects were minimal for typical cruise conditions, even for Reynold's numbers as low as two million. The effect of wind-tunnel walls on experiment-theory correlations remained inconclusive. A wing-body code was used to calculate the flow field about a wing-body configuration with body-mounted engines, typical of the transonic Biz-Jet aircraft.

Hicks, R. M.↗

NASA NTRS1981

Overview of advanced wing design

Examples of experiment theory correlation are presented to give an indication of the capabilities and limitations of wing design and analysis for transonic applications by potential flow theory. The examples include correlations of experimental pressure distributions with theoretical results from isolated wing codes and wing-body codes. Both conservative and non conservative differencing as well as body and boundary layer corrections are considered. A full potential isolated wing code correlates well with data from an isolated wing test but may give poor prediction of the aerodynamic characteristics of some wing-body configurations. Potential flow wing body codes were found to improve the correlation for the wing-body configurations considered.

Hicks, R. M.↗

NASA NTRS1980

An experimental evaluation of a helicopter rotor section designed by numerical optimization

The wind tunnel performance of a 10-percent thick helicopter rotor section design by numerical optimization is presented. The model was tested at Mach number from 0.2 to 0.84 with Reynolds number ranging from 1,900,000 at Mach 0.2 to 4,000,000 at Mach numbers above 0.5. The airfoil section exhibited maximum lift coefficients greater than 1.3 at Mach numbers below 0.45 and a drag divergence Mach number of 0.82 for lift coefficients near 0. A moderate 'drag creep' is observed at low lift coefficients for Mach numbers greater than 0.6.

Hicks, R. M.↗

NASA NTRS1980

Computerized three-dimensional aerodynamic design of a lifting rotor blade

A three-dimensional, inviscid, full-potential lifting rotor code was used to demonstrate that pressure distributions on both advancing and retreating blades could be significantly improved by perturbing local airfoil sections. The perturbations were described by simple geometric shape functions. To illustrate the procedure, an example calculation was made at a forward flight speed of 85 m/sec (165 knots) and an advance ratio of 0.385. It was found that a minimum of three shape functions was required to improve the pressures without producing undesirable secondary effects in high-speed forward flight on a hypothetical modern rotor blade initially having an NLR-1 supercritical airfoil. Reductions in the shock strength on the advancing blade could be achieved, while simultaneously lessening leading-edge pressure gradients on the retreating blade. The major blade section modifications required were blunting of the upper surface leading edge and some reshaping of the blade's upper surface resulting in moderately thicker airfoils.

Tauber, M. E.↗

NASA NTRS1979

Upper-surface modifications for C sub l max improvement of selected NASA 6-series airfoils

The thickness of the upper surface of 64 airfoils was increased from the leading edge to the position of maximum thickness. The modifications were generated using a numerical optimization routine coupled with an aerodynamic analysis code. The type of modification presented can be used for aircraft design or for the retrofit of current aircraft to improve the stall characteristics and climb performance. The coordinates of the modified airfoils are presented with plots of the forward 45% of the profiles and pressure distributions for both the modified and unmodified sections at an angle of attack of 14 degrees.

Szelazek, C. A.↗

NASA NTRS1979

Effects of upper surface modification on the aerodynamic characteristics of the NACA 63 sub 2-215 airfoil section

An upper surface modification designed to increase the maximum lift coefficient of a 63 sub 2 - 215 airfoil section was tested at Mach numbers of 0.2, 0.3, and 0.4 Reynolds numbers of 1.3 x 1 million, 2 x 10 sub 6 and 2.5 x 1 million. Comparisons of the aerodynamic coefficients before and after the modification were made. The upper surface modification increased the maximum lift coefficient of the airfoil significantly at all conditions.

Hicks, R. M.↗

NASA NTRS1979

Application of numerical optimization to the design of advanced supercritical airfoils

An application of numerical optimization to the design of advanced airfoils for transonic aircraft showed that low-drag sections can be developed for a given design Mach number without an accompanying drag increase at lower Mach numbers. This is achieved by imposing a constraint on the drag coefficient at an off-design Mach number while minimizing the drag coefficient at the design Mach number. This multiple design-point numerical optimization has been implemented with the use of airfoil shape functions which permit a wide range of attainable profiles during the optimization process. Analytical data for the starting airfoil shape, a single design-point optimized shape, and a double design-point optimized shape are presented. Experimental data obtained in the NASA Ames two-by two-foot wind tunnel are also presented and discussed.

Johnson, R. R.↗

NASA NTRS1979

Supercritical wing design using numerical optimization and comparisons with experiment

A numerical minimization scheme is used in conjunction with two-dimensional and three-dimensional inviscid transonic flow analysis codes to provide procedures for wing leading edge aerodynamic design. The procedures are demonstrated in the design of a new leading edge to improve C-141 cruise performance. For the high aspect ratio moderately swept C-141 wing, the 2-D procedure is shown to yield results which are in close agreement with those obtained using the 3-D technique. Although the 2-D approach uses much less computation time than the 3-D technique, the latter requires fewer manhours than the former. Comparisons of predicted and wind tunnel measured performance improvements are presented which verify the design procedures.

Lores, M. E.↗

NASA NTRS1979

Computational optimization and wind tunnel test of transonic wing designs

A practical procedure for the optimum design of transonic wings is demonstrated. The procedure uses an optimization program based on the method of feasible directions coupled with an aerodynamic analysis program which solves the three-dimensional potential equation for subsonic through transonic flow. Two new wings for the A-7 aircraft were designed by using the optimization procedure to achieve specified surface pressure distributions. The new wings, along with the existing A-7 wing, were tested in the Ames 11-foot transonic wind tunnel. The experimental data show that all of the performance goals were met.

Haney, H. P.↗

NASA NTRS1978

Airfoil design by numerical optimization using a minicomputer

A computer program developed for the automated design of low speed airfoils utilizes a generalized Joukowski method for aerodynamic analysis coupled with a conjugate gradient, penalty function, numerical optimization algorithm to give an efficient calculation technique for use with minicomputers. The program designs airfoils with a prescribed pressure distribution as well as those which minimize or maximize some aerodynamic force coefficient. At present the method is restricted to inviscid, incompressible flow. A typical design problem will execute in 4.5 hr on an HP 9830 minicomputer.

Hicks, R. M.↗

NASA NTRS1978

Wing analysis using a transonic potential flow computational method

The ability of the method to compute wing transonic performance was determined by comparing computed results with both experimental data and results computed by other theoretical procedures. Both pressure distributions and aerodynamic forces were evaluated. Comparisons indicated that the method is a significant improvement in transonic wing analysis capability. In particular, the computational method generally calculated the correct development of three-dimensional pressure distributions from subcritical to transonic conditions. Complicated, multiple shocked flows observed experimentally were reproduced computationally. The ability to identify the effects of design modifications was demonstrated both in terms of pressure distributions and shock drag characteristics.

Henne, P. A.↗