Engineering topics

Hicks, R. M.

Publications and source records attributed to Hicks, R. M..

At least 37 records · Page 2

NASA NTRS1978

Transonic wing analysis using advanced computational methods

This paper discusses the application of three-dimensional computational transonic flow methods to several different types of transport wing designs. The purpose of these applications is to evaluate the basic accuracy and limitations associated with such numerical methods. The use of such computational methods for practical engineering problems can only be justified after favorable evaluations are completed. The paper summarizes a study of both the small-disturbance and the full potential technique for computing three-dimensional transonic flows. Computed three-dimensional results are compared to both experimental measurements and theoretical results. Comparisons are made not only of pressure distributions but also of lift and drag forces. Transonic drag rise characteristics are compared. Three-dimensional pressure distributions and aerodynamic forces, computed from the full potential solution, compare reasonably well with experimental results for a wide range of configurations and flow conditions.

Henne, P. A.↗

NASA NTRS1977

Wing design by numerical optimization

A study was conducted to assess the feasibility of performing computerized wing design by numerical optimization. The design program combined a full potential, inviscid aerodynamics code with a conjugate gradient optimization algorithm. Three design problems were selected to demonstrate the design technique. The first involved modifying the upper surface of the inboard 50% of a swept wing to reduce the shock drag subject to a constraint on wing volume. The second involved modifying the entire upper surface of the same swept wing (except the tip section) to increase the lift-drag ratio subject to constraints on wing volume and lift coefficient. The final problem involved modifying the inboard 50% of a low-speed wing to achieve good stall progression. Results from the three cases indicate that the technique is sufficiently accurate to permit substantial improvement in the design objectives.

Hicks, R. M.↗

NASA NTRS1977

Application of numerical optimization to the design of supercritical airfoils without drag-creep

Recent applications of numerical optimization to the design of advanced airfoils for transonic aircraft have shown that low-drag sections can be developed for a given design Mach number without an accompanying drag increase at lower Mach numbers. This is achieved by imposing a constraint on the drag coefficient at an off-design Mach number while the drag at the design Mach number is the objective function. Such a procedure doubles the computation time over that for single design-point problems, but the final result is worth the increased cost of computation. The ability to treat such multiple design-point problems by numerical optimization has been enhanced by the development of improved airfoil shape functions. Such functions permit a considerable increase in the range of profiles attainable during the optimization process.

Hicks, R. M.↗

NASA NTRS1976

Numerical Airfoil Optimization Using a Reduced Number of Design Coordinates

A method is presented for numerical airfoil optimization whereby a reduced number of design coordinates are used to define the airfoil shape. The approach is to define the airfoil as a linear combination of shapes. These basic shapes may be analytically or numerically defined, allowing the designer to use his insight to propose candidate designs. The design problem becomes one of determining the participation of each such function in defining the optimum airfoil. Examples are presented for two-dimensional airfoil design and are compared with previous results based on a polynomial representation of the airfoil shape. Four existing NACA airfoils are used as basic shapes. Solutions equivalent to previous results are achieved with a factor of more than 3 improvements in efficiency, while superior designs are demonstrated with an efficiency greater than 2 over previous methods. With this shape definition, the optimization process is shown to exploit the simplifying assumptions in the inviscid aerodynamic analysis used here, thus demonstrating the need to use more advanced aerodynamics for airfoil optimization.

Vanderplaats, G. N.↗

NASA NTRS1976

Airfoil section drag reduction at transonic speeds by numerical optimization

A practical procedure for the design of low drag, transonic airfoils is demonstrated. The procedure uses an optimization program, based on a gradient algorithm coupled with an aerodynamic analysis program, that solves the full, non-linear potential equation for transonic flow. The procedure is useful for the design of retrofit modifications for drag reduction of existing aircraft as well as for the design of low drag profiles for new aircraft. Results are presented for the modification of four different airfoils to decrease the drag at a given transonic Mach number.

Hicks, R. M.↗

NASA NTRS1976

An evaluation of the method for determining the Whitham F-function using distributions of downwash and sidewash angles

The method of computing the Whitham F function using distributions of downwash and sidewash angles was evaluated with two different models. F functions which were calculated for a half angle cone cylinder at M infinites = 2.01, using theoretically and experimentally derived flow angles, show that the method is sensitive to small inaccuracies in the measured flow angles. An oblique wing transport model was tested at 0 deg angle of attack at M infinitely = 2.01. In this test, two different probes were used at two different distances from the model. The pressure signature derived from the F function was extrapolated and compared to the pressure signature measured at the distance of 0.87 body lengths with the static pressure probe. The agreement between the two pressure signatures was poor due to the many inaccuracies involved in using a probe designed to measure flow angularity.

Mendoza, J. P.↗

NASA NTRS1976

Airfoil section drag reduction at transonic speeds by numerical optimization

Hicks, R. M.↗

NASA NTRS1975

Effects of forward contour modification on the aerodynamic characteristics of the NACA 641-212 airfoil section

Two different forward contour modifications designed to increase the maximum lift coefficient of the NACA 64 sub 1-212 airfoil section were evaluated experimentally at low speeds. One modification consisted of a slight droop of the leading edge with an increased leading-edge radius; the other modification incorporated increased thickness over the forward 35 percent of the upper surface of the profile. Both modified airfoil sections were found to provide substantially higher maximum lift coefficients than the 64 sub 1-212 section. The drooped leading-edge modification incurred a drag penalty of approximately 10 percent at low and moderate lift coefficients and exhibited a greater nosedown pitching moment than the 64 sub 1-212 profile. The upper surface modification produced about the same drag level as the 64 sub 1-212 section at low and moderate lift coefficients and less nosedown pitching moment than the 64 sub 1-212 profile. Both modified airfoil sections had lower drag coefficients than the 64 sub 1-212 section at high lift coefficients.

Hicks, R. M.↗

NASA NTRS1975

Design of low-speed airfoils by numerical optimization

A practical procedure for the optimum design of low-speed airfoils is demonstrated. The procedure uses an optimization program based on a gradient algorithm coupled with an aerodynamic analysis program that uses a relaxation solution of the inviscid, full-potential equation. The analysis program is valid for both incompressible and compressible flow, thereby making optimum design of high-speed, shock-free airfoils possible. Results are presented for the following three constrained optimization problems at fixed angle of attack and Mach number: (1) adverse pressure-gradient minimization, (2) pitching-moment minimization; and (3) lift maximization. All three optimization problems were studied with various aerodynamic and geometric constraints.

Hicks, R. M.↗

NASA NTRS1975

Application of numerical optimization to the design of low speed airfoils

A practical procedure for the optimum design of low-speed airfoils is demonstrated. The procedure uses an optimization program based on the method of feasible directions coupled with an aerodynamic analysis program that uses a relaxation solution of the inviscid, full potential equation. Results are presented for airfoils designed to have small adverse pressure gradients, high maximum lift, and low pitching moment.

Hicks, R. M.↗

NASA NTRS1974

An assessment of airfoil design by numerical optimization

A practical procedure for optimum design of aerodynamic shapes is demonstrated. The proposed procedure uses an optimization program based on the method of feasible directions coupled with an analysis program that uses a relaxation solution of the inviscid, transonic, small-disturbance equations. Results are presented for low-drag, nonlifting transonic airfoils. Extension of the method to lifting airfoils, other speed regimes, and to three dimensions if feasible.

Hicks, R. M.↗

NASA NTRS1973

Shuttle sonic boom - Technology and predictions

Because the shuttle differs significantly in both geometric and operational characteristics from conventional supersonic aircraft, estimation of sonic boom characteristics required a new technology base. The prediction procedures thus developed are reviewed. Flight measurements obtained for both the ascent and entry phases of the Apollo 15 and 16 and for the ascent phase only of the Apollo 17 missions are presented which verify the techniques established for application to shuttle. Results of extensive analysis of the sonic boom overpressure characteristics completed to date are presented which indicate that this factor of the shuttle's environmental impact is predictable, localized, of short duration and acceptable. Efforts are continuing to define the shuttle sonic boom characteristics to a fine level of detail based on the final system design.

Holloway, P. F.↗

NASA NTRS1973

Pressure signatures for a .00053 scale model of the Saturn 5-Apollo launch vehicle with simulated exhaust plumes

Wind tunnel pressure signatures are presented for 10 Mach numbers over a range from 3.01 to 7.29 for a .00053-scale model of the Saturn 5 Apollo launch vehicle complete with escape tower and solid body simulated exhaust plumes for each Mach number. The effect of simulated plume length on the wind tunnel pressure signature was investigated at Mach 4.01. An analysis of the error incurred by extrapolating pressure signatures having strong shock waves by weak shock procedures is presented.

Hicks, R. M.↗

NASA NTRS1973

A wind tunnel flight correlation of Apollo 16 sonic boom

A correlation of sonic boom pressure signatures recorded during reentry of the Apollo 16 command module with wind-tunnel signatures extrapolated to flight distances was made for Mach numbers of 1.83 and 9.71. The flight pressure signatures were recorded by microphones located onboard ships positioned near the ground track, whereas the wind tunnel signatures were measured during a test of a 0.016-scale model of the command module. The agreement between estimates based on wind tunnel data and flight measurements was good at the tested Mach numbers.

Garcia, F., Jr.↗

NASA NTRS1973

Oblique-wing sonic boom

An investigation was conducted to determine the magnitude of the groundtrack overpressure generated by an oblique-wing transport cruising at Mach 1.4 at 45,000 ft. A conventional swept-wing configuration was included in the study to provide a basis of comparison for the oblique-wing configuration. The results of the investigation have shown that the oblique-wing configuration produces less sonic boom overpressure at cruise lift coefficient than the swept-wing vehicle.

Hicks, R. M.↗

NASA NTRS1973

Some Effects of Wing Planform on Sonic Boom

A wind-tunnel investigation was conducted to determine the effect of wing planform on sonic boom at Mach numbers of 1.7, 2.0, and 2.7. The results of the investigation show that the wing leading-edge sweep is one of the primary planform variables affecting the overpressure characteristics.

Hunton, L. W.↗

NASA NTRS1972

Pressure signatures for the Apollo command module and the Saturn 5 launch vehicle with a discussion of strong shock extrapolation procedures

Wind tunnel pressure signatures measured at Mach 10.1 for model of the Apollo Command Module and at Mach numbers from 3.01 to 7.91 for two models of the Saturn launch configuration are presented. The signatures for the command module were obtained at roll angles ranging from 0 deg to 180 deg. A brief discussion of the extrapolation of strong pressure signatures is included in the report.

Hicks, R. M.↗

NASA NTRS1972

A Wind Tunnel Flight Correlation of Apollo 15 Sonic Boom

A correlation of sonic boom pressure signatures recorded during reentry of the Apollo 15 command module with wind-tunnel signatures extrapolated to flight distances has been made for Mach numbers of 1.16 and 4.57. The flight pressure signatures were recorded by pressure sensors located onboard ships positioned near the ground track while the wind-tunnel signatures were measured during tests of a 0.016-scale model of the command module. The agreement between estimates based on wind-tunnel data and flight measurements was better at Mach 4.57 than at Mach 1.16.

Hicks, R. M.↗