Search NASA⌕ Search

Engineering topics

Hogan, John

Publications and source records attributed to Hogan, John.

At least 19 records

LCLS-II-HE Cavity Qualification Testing

Acceptance testing of the LCLS-II-HE production cavities is approximately 65% complete. In this report, we present details of the test results, including summaries of the quench fields, intrinsic quality factors, and experience with field emission. We also offer an outlook on the remaining tests to be performed.

43 PARTICLE ACCELERATORS↗

Flux Expulsion Testing for LCLS-II-HE Cavity Production

Nitrogen-doped niobium SRF cavities are sensitive to trapped magnetic flux, which decreases the cavity intrinsic Q₀. Prior experimental results have shown that heat treatments to 900°C and higher can result in stronger flux expulsion during cooldown; the precise temperature required tends to vary by vendor lot/ingot of the niobium material used in the cavity cells. For LCLS-II-HE, to ensure sufficient flux expulsion in all cavities, we built and tested single-cell cavities to determine this required temperature for each vendor lot of niobium material to be used in cavity cells. In this report, we present the results of the single-cell flux expulsion testing and the Q₀ of the nine-cell cavities built using the characterized vendor lots. We discuss mixing material from different vendor lots, examine the lessons learned, and finally present an outlook on possible refinements to the single-cell technique.

43 PARTICLE ACCELERATORS↗

LCLS-II-HE Status at Fermilab

The LCLS-II-HE project is an upgrade to the Linac Coherent Light Source facility at SLAC National Accelerator Laboratory. Fermilab is part of the LCLS-II-HE collaboration and will deliver 14 cryomodules to SLAC for LCLS-II-HE. These cryomodules consist of eight 1.3 GHz 9-cell cavities. Cryomodule production is in progress, and four cryomodules have been delivered to SLAC. One of the cryomodules already delivered is the verification cryomodule that reached 200 MV total voltage in continuous wave mode. Status of cryomodule production, and lessons learned will be presented. Fermilab is also designing a buncher cryomodule as part of a low emittance injector design for the project. The design is near completion, and status will be reported.

Kaluzny, Joshua↗

LCLS-II-HE Vertical Acceptance Testing Plans

LCLS-II-HE has performance requirements similar to but generally more demanding than those of LCLS-II, with an operating gradient of 21 MV/m (up from 16 MV/m in LCLS-II) and tighter restrictions on field emission and multipacting. In this paper, we outline the requirements for the 1.3 GHz cavities and the plans for qualification of these cavities by vertical test. We discuss lessons learned from LCLS-II and highlight the changes implemented in the vertical test procedure for the new project.

43 PARTICLE ACCELERATORS↗

Statistical Modeling of Peak Accelerating Gradients in LCLS-II and LCLS-II-HE

In this report, we study the vertical test gradient performance and the gradient degradation between vertical test and cryomodule test for the 1.3 GHz LCLS-II cavities. We develop a model of peak gradient statistics, and use our understanding of the LCLS-II results and the changes implemented for LCLS-II-HE to estimate the expected gradient statistics for the new machine. Finally, we lay out a plan to ensure that the LCLS-II-HE cryomodule gradient specifications are met while minimizing cavity disqualification by introducing a variable acceptance threshold for the accelerating gradient.

43 PARTICLE ACCELERATORS↗

Results of the Micro-12 Flight Experiment: Effects of Microgravity on Shewanella oneidensis MR-1

The Micro-12 flight experiment was launched on SpaceX-15 and completed during berthing on the International Space Station. The goal of this experiment was to understand the effects of spaceflight and microgravity on the physiology of the model exoelectrogen Shewanella oneidensis MR-1. BioServe Fluid Processing Apparatus (FPA) and Group Activation Pack (GAP) hardware systems were used for both flight and ground control tests. Under spaceflight conditions, extracellular electron transfer (EET) rates were found to be significantly increased on insoluble substrates, while biofilm development appeared to be unchanged under the conditions tested; these processes are critical for microbial-assisted bioelectrochemical systems. Additionally, RNAseq analysis, proteomic profiling, and competitive mutant fitness profiling were performed to gain further understanding of microbial physiology under EET-respiring conditions during spaceflight. Overall, the results of the Micro-12 project support the idea that Shewanella oneidensis MR-1, in particular, and exoelectrogens in general could be useful chassis organisms for synthetic biology applications using microbial bioelectrochemical systems. These findings will assist bioengineering and synthetic biology development efforts harnessing the unique capabilities of exoelectrogens for life support and in situ resource utilization.

Dougherty, Michael↗

BioNutrients-1: On-Demand Production of Nutrients in Space

Future long-duration missions face significant challenges maintaining crew health. A critical area is supplying adequate nutrition, as certain vitamins and nutrients in supplied foods and supplements demonstrate substantial degradation during extended storage. To address this issue, we are developing and flight-testing a platform technology that demonstrates in situ microbial production of targeted nutrients over extended mission durations. This 5-year experiment, known as BioNutrients-1, was started on the International Space Station in May 2019. It involves two components: an on-orbit hydration and production experiment; and the development of space-compatible, key bio-manufacturing microorganisms. On-orbit testing utilizes a small "production pack" system that encloses sterile edible growth substrate and desiccated Saccharomyces cerevisiae strains genetically engineered to produce the nutrients beta-carotene or zeaxanthin. On hydration and mixing of the production pack, the organisms revive and grow until limited by the depletion of growth media, hypothetically leading to consistent amounts of biomass and nutrients. In eventual mission applications, the packet contents would be heat treated to inactivate the microorganisms prior to consumption. For these flight experiments, the packet will not be heat treated, but will instead be frozen for return to Earth for analyses. In addition to the production pack trials, 14 different microorganisms/treatments were also delivered to ISS for long-duration storage. These samples will be intermittently returned to Earth and analyzed to determine survival rates and genomics. For this presentation, initial data from returned samples and ground controls will be discussed.

Hindupur, Aditya↗

Instrumentation and Control Selection for the 12 GeV Hall-B Magnets at Jefferson Lab

Here, as part of the Jefferson Lab 12 GeV accelerator upgrade, the Experimental Physics Hall B detector system requires two superconducting magnets – a Torus and a Solenoid. The specifications required maximum space for the detectors which led to the choice of conduction cooling for each magnet. The Torus consists of 6 trapezoidal 'race-track'-type coils connected in series with an operating current of 3770 A. The Solenoid is an actively shielded 5 Tesla magnet consisting of 5 coils connected in series operating at 2416 A. Within the hall the two magnets are located in close proximity to each other and are surrounded by particle detectors. We describe the philosophy behind the instrumentation selection and control design that accounts for this proximity and other challenging working conditions. We describe the choice of sensor technologies, as well as the control and data acquisition methods. The magnet power and cryogenic control sub-systems are implemented using Allen Bradley Control Logix 1756-L72 Programmable Logic Controllers. Sensor instrumentation read-backs are routed into the PLC via National Instruments cRIO hardware (Field Programmable Gate Arrays or FPGA/RT application) using Jefferson Lab designed FPGA-based multi-sensor-excitation-chassis. Configuration, monitoring, and alarm handlers for the magnet systems are provided via an Experimental Physics Instrumentation & Control System interface (EPICS). Failure Modes and Effects Analysis (FMEA) and the requirement to monitor critical parameters during operation guided the selection of instrumentation and associated hardware. The design of the quench protection and voltage tap sub-systems was driven by the anticipated level of voltages developed during a magnet quench. The primary hard-wired quench detection and protection sub-system together with the secondary PLC-based protection sub-system is also discussed. The successful commissioning and subsequent performance of these magnets demonstrates the robustness of the design and implementation approach that was adopted by the Jefferson Lab team and serves as an excellent 'How To' guide for future projects of this size and complexity.

12 GeV↗

Zeolite Degradation: An Investigation of CO2 Capacity Loss of 13x Sorbent

System testing of the Carbon Dioxide Removal and Compression System (CRCS) has revealed that sufficient CO2 removal capability was not achieved with the designed system. Subsystem component analysis of the zeolite bed revealed that the sorbent material suffered significant degradation and CO2 loading capacity loss. In an effort to find the root cause of this degradation, various factors were investigated to try to reproduce the observed performance loss. These factors included contamination by vacuum pump oil, o-ring vacuum grease, loading/unloading procedures, and operations. This paper details the experiments that were performed and their results.

Air Revitalization↗

Development of Storage Methods for Saccharomyces Strains to be Utilized for In situ Nutrient Production in Long-Duration Space Missions

Long-duration space missions will benefit from closed-loop life support technologies that minimize mass, volume, and power as well as decrease reliance on Earth-based resupply. A system for In situ production of essential vitamins and nutrients can address the documented problem of degradation of stored food and supplements. Research has shown that the edible yeast Saccharomyces cerevisiae can be used as an on-demand system for the production of various compounds that are beneficial to human health. A critical objective in the development of this approach for long-duration space missions is the effective storage of the selected microorganisms. This research investigates the effects of different storage methods on survival rates of the non-sporulating probiotic S. boulardii, and S. cerevisiae spores and vegetative cells. Dehydration has been shown to increase long-term yeast viability, which also allows increased shelf-life and reduction in mass and volume. The process of dehydration causes detrimental effects on vegetative cells, including oxidative damage and membrane disruption. To maximize cell viability, various dehydration methods are tested here, including lyophilization (freeze-drying), air drying, and dehydration by vacuum. As a potential solution to damage caused by lyophilization, the efficacy of various cryoprotectants was tested. Furthermore, in an attempt to maintain higher survival rates, the effect of temperature during long-term storage was investigated. Data show spores of the wild-type strain to be more resilient to dehydration-related stressors than vegetative cells of either strain, and maintain high viability rates even after one year at room temperature. In the event that engineering the organism to produce targeted nutrient compounds interferes with effective sporulation of S. cerevisiae, a more robust method for improving vegetative cell storage is being sought. Therefore, anhydrobiotic engineering of S. cerevisiae and S. boulardii is being conducted

nutrient↗

Zeolite Degradation: An Investigation of CO2 Capacity Loss of 13x Sorbent

System testing of the Carbon Dioxide Removal and Compression System (CRCS) has revealed that sufficient CO2 removal capability was not achieved with the designed system. Subsystem component analysis of the zeolite bed revealed that the sorbent material suffered significant degradation and CO2 loading capacity loss. In an effort to find the root cause of this degradation, various factors were investigated to try to reproduce the observed performance loss. These factors included contamination by vacuum pump oil, o-ring vacuum grease, loadingunloading procedures, and operations. This paper details the experiments that were performed and their results.

ECLSS↗

Performance of Silica Gel in the Role of Residual Air Drying. Part II.

Removal of carbon dioxide (CO2) is a necessary step in air revitalization and is often accomplished with sorbent materials. Since moisture competes with CO2 in zeolite sorbent materials, it is necessary to remove the water first. This is typically accomplished in two stages: “bulk” removal and “residual” drying. Silica gel is used as the bulk drying material in the Carbon Dioxide Removal Assembly (CDRA) in operation on the ISS (International Space Station). There has been some speculation that silica gel may also be capable of serving as both bulk and residual drying material to reduce system mass and Foreign Object Debris (FOD). Previous research tested silica gel alone as drying material. However, the silica gel volume used was not comparable to the current amount used on the CDRA. Therefore, the tests were repeated with the new silica gel volume. This paper discusses the fabrication and assembly of the modified canister to accommodate the new volume, the testing, and the evaluation of the test results.

Air Revitalization↗

Progress on the CO2 Removal and Compression System

The Carbon Dioxide Removal and Compression System (CRCS) is designed to perform both the Carbon Dioxide(CO2) removal and compress CO2 for further processing. The CRCS was designed as a lower power requirement option to the one currently being used on the International Space Station (ISS). This paper describes the final design, fabrication, assembly, and testing of the integrated CRCS. Initial results indicated that the spiral heaters used did not yield uniform heating within both the adsorption and compression beds. In addition, the heaters for the compression bed were insufficient and an additional HVAC jacket was employed to provide heat to the bed.

Air Revitalization↗

3D Photocatalytic Air Processor for Dramatic Reduction of Life Support Mass and Complexity

To dramatically reduce the cost and risk of CO2 management systems in future extended missions, we have conducted preliminary studies on the materials and device development for advanced "artificial photosynthesis" reaction systems termed the High Tortuosity PhotoElectroChemical (HTPEC) system. Our Phase I studies have demonstrated that HTPEC operates in much the same way a tree would function, namely directly contacting the cabin air with a photocatalyst in the presence of light and water (as humidity) to immediately conduct the process of CO2 reduction to O2 and useful, "tunable" carbon products. This eliminates many of the inefficiencies associated with current ISS CO2 management systems. We have laid the solid foundation for Phase II work to employ novel and efficient reactor geometries, lighting approaches, 3D manufacturing methods and in-house grown novel catalytic materials.The primary objective of the proposed work is to demonstrate the scientific and engineering foundation for light-activated, compact devices capable of converting CO2 to O2 and mission-relevant carbon compounds. The proposed HTPEC CO2 management system will demonstrate a novel pathway with high efficiency and reliability in a compact, lightweight reactor architecture. The proposed HTPEC air processing concept can be developed in multiple architectures, such as centralized processing as well as "artificial leaves" distributed throughout the cabin that utilize pre-existing cabin ventilation (wind). Additionally, HTPEC can be deployed with spectrally tunable collection channels for selectable product generation. HTPEC employs light as its only energy source to remove and convert waste CO2 using a non-toxic composite catalyst.We have demonstrated in the Phase I studies the production, tunability and robustness of the novel composite catalysts following the preliminary work in the Chen laboratory. Additionally, we have designed, fabricated and tested all components of HTPEC device with active materials, including flow modeling to optimize flow mixing and pressure drop as well as the production of ethylene and other larger hydrocarbons. To best determine how this technology could be implemented, we also performed system integration optimization and trade studies. This includes parameters such as mass, volume, power in relation to selected mission configurations, CO2 delivery methods and light source/delivery approaches.

Artificial Photosynthesis↗

The Utilization of Urine Processing for the Advancement of Life Support Technologies

The success of long-duration missions will depend on resource recovery and the self-sustainability of life support technologies. Current technologies used on the International Space Station (ISS) utilize chemical and mechanical processes, such as filtration, to recover potable water from urine produced by crewmembers. Such technologies have significantly reduced the need for water resupply through closed-loop resource recovery and recycling. Harvesting the important components of urine requires selectivity, whether through the use of membranes or other physical barriers, or by chemical or biological processes. Given the chemical composition of urine, the downstream benefits of urine processing for resource recovery will be critical for many aspects of life support, such as food production and the synthesis of biofuels. This paper discusses the beneficial components of urine and their potential applications, and the challenges associated with using urine for nutrient recycling for space application.

Resource Recovery↗

COMMISSIONING AND OPERATION OF THE CEBAF 100 MV CRYOMODULES

The Continuous Electron Beam Accelerator Facility (CEBAF) energy upgrade from 6 GeV to 12 GeV includes the installation of ten new 100 MV cryomodules and RF systems. The superconducting RF cavities are designed to operate CW at a maximum accelerating gradient of 19.3 MV/m. To support the higher gradients and higher Q{sub L} ({approx} 3 x 10{sup 7}), a new RF system has been developed and is being installed to power and control the cavities. The RF system employs digital control and 13 kW klystrons. Recently, two of these cryomodules and associated RF hardware and software have been installed and commissioned in the CEBAF accelerator. Electrons at linac currents up to 540 {micro}A have been successfully accelerated and used for nuclear physics experiments. This paper reports on the commissioning and operation of the RF system and cryomodules.

43 PARTICLE ACCELERATORS↗