Search NASA⌕ Search

Engineering topics

Holman, Zachary C.

Publications and source records attributed to Holman, Zachary C..

At least 19 records

Optical constants of polycrystalline Al 0.25 Ga 0.75 P and Al 0.9 Ga 0.1 As determined by variable-angle spectroscopic ellipsometry

The optical constants of single-crystal Al x Ga 1-x P and Al x Ga 1-x As have been widely studied at various Al compositions but have not yet been thoroughly investigated as polycrystalline materials. Using variable-angle spectroscopic ellipsometry, we estimate and analyze the optical constants of polycrystalline Al 0.25 Ga 0.75 P and Al 0.9 Ga 0.1 As that were non-epitaxially deposited at deposition temperatures of either 250 or 420 °C, and with various dopant species, dopant concentrations, and V/III flux ratios. Here, for wavelengths of 350–400 nm, decreasing the V/III ratio increases the refractive index of Be-doped polycrystalline Al 0.25 Ga 0.75 P. For wavelengths >500 nm, as the targeted Be dopant concentration increases for polycrystalline Al 0.25 Ga 0.75 P, the amount the extinction coefficient increases and the indirect bandgap decreases depends on the V/III ratio. Furthermore, Si-doped polycrystalline Al 0.25 Ga 0.75 P has significantly smaller extinction coefficient values than when it is Be-doped, for the same V/III ratio and targeted doping concentration, at wavelengths >500 nm. Based on our findings, we hypothesize that the dopant species, dopant concentration, and the V/III ratio dictate various types of defect concentrations, which then affect the optical constants and indirect bandgap of polycrystalline Al 0.25 Ga 0.75 P. Additionally, for wavelengths >500 nm, we find that polycrystalline Al 0.25 Ga 0.75 P and Al 0.9 Ga 0.1 As have the lowest extinction coefficient values when deposited at 420 °C, as opposed to 250 °C. Thus, we hypothesize that the deposition temperature is the most significant factor in dictating the optical constants of these polycrystalline III-Vs. Ultimately, this work demonstrates alternative methods to tune the optical constants of polycrystalline Al 0.25 Ga 0.75 P and Al 0.9 Ga 0.1 As, as opposed to tuning the Al composition.

42 ENGINEERING↗

Recycling Silicon Bottom Cells from End-of-Life Perovskite–Silicon Tandem Solar Cells

Perovskite-silicon tandem cells have shown much higher efficiencies than the single junction cells, which promises further reduction of energy cost from photovoltaics. Due to the protection by perovskites, silicon subcells in perovskite-silicon tandem cells may last much longer than they are designed for single junction devices. Here we report recycling silicon bottom cells from end-of-life perovskite-silicon tandem solar cells which further reduce their cost and enhance the sustainability. We demonstrate that silicon bottom cells can be recycled from end-oflife tandem cells by thermal delamination and chemical cleaning processes. The optoelectronic properties of silicon bottom cells were shown largely unchanged at the end-of-life tandem cells. The tandem cells refurbished from recycled silicon bottom cells show comparable efficiencies with those fabricated from fresh ones.

14 SOLAR ENERGY↗

Charge Carrier Lifetime Determination in Graded Absorber Solar Cells Using Time‐Resolved Photoluminescence Simulations and Measurements

Thin‐film photovoltaic device efficiencies are limited by carrier recombination, thus understanding recombination mechanisms is critical for performance improvements. Bulk minority carrier lifetime ( τ bulk ) is a critical parameter for solar cells but is difficult to determine in P–N junction devices, especially for high doping. As doping ≥10 16 cm −3 is required for efficient drift‐charge‐carrier‐collection devices, a method for τ bulk determination in doped P–N junction devices is necessary. This work utilizes time‐resolved photoluminescence (TRPL) simulations to quantify bulk and interface recombination properties in highly doped, graded absorber CdSeTe structures. The two methods developed here for τ bulk determination include utilization of an instantaneous lifetime representation to guide TRPL fitting and direct comparison between measured and simulated decays. Simulations verified that both methods are valid for state‐of‐the‐art device architectures which include graded bandgap absorbers, graded doping, and graded lifetimes. Shifts in the dominant recombination mechanism are identified for sufficiently long τ bulk , where front and back interface quality plays a more prominent role. Evaluation of surface recombination velocities and conduction band offset illustrate electro‐optical advantages of a positive conduction band offset and highlight the necessity of improved interfaces as bulk quality in photovoltaic devices improves.

14 SOLAR ENERGY↗

Electro-Optical Characterization of Arsenic-Doped CdSeTe and CdTe Solar Cell Absorbers Doped in-situ During Close Space Sublimation

Most contemporary device models predict that an acceptor concentration of at least 10^16 cm^-3 is required to reach an open circuit voltage of 1 V in polycrystalline CdTe-based solar cells. While copper has traditionally been used as the de facto p-type dopant in polycrystalline cadmium telluride (CdTe) and cadmium selenide telluride (CdSeTe), reaching high acceptor concentrations has proved to be challenging in such devices due to significant dopant compensation. The acceptor concentration in copper-doped CdTe and CdSeTe typically ranges from 10^13 to 10^15 cm^-3 and routinely exhibit low external radiative efficiencies below 0.01%, limiting their implied voltage (i.e., quasi-Fermi level splitting) to approximately 900 mV. As an alternative to copper, this work explores the use of arsenic as a p-type dopant for CdTe and CdSeTe. Using a novel technique in which a thin layer of arsenic-containing material is deposited and used as a reservoir for arsenic to diffuse into a front layer of previously undoped material, this contribution demonstrates that high external radiative efficiencies are achievable, a direct result of combined high acceptor concentrations and long minority-carrier lifetimes in the absorber. This leads to improved implied voltages, and indicates that As-doping represents a promising pathway towards improving the external voltage of CdSeTe/CdTe solar cells.

cadmium telluride↗

Bifacial all-perovskite tandem solar cells

The efficiency of all-perovskite tandem devices falls far below theoretical efficiency limits, mainly because a widening bandgap fails to increase open-circuit voltage. We report on a bifacial all-perovskite tandem structures with an equivalent efficiency of 29.3% under back-to-front irradiance ratio of 30. This increases energy yield and reduces the required bandgap of a wide-bandgap cell. Open-circuit voltage deficit is therefore minimized, although its performance under only front irradiance is not ideal. The bifacial device needs a sputtered rear transparent electrode, which could reduce photon path length and deteriorate stability of Pb-Sn perovskites. Embedding a light-scattering micrometer-sized particle layer into perovskite to trap light, effectively increases absorptance by 5 to 15% in the infrared region. Using a nonacidic hole transport layer markedly stabilizes the hole-extraction interface by avoiding proton-accelerated formation of iodine. These two strategies together increase efficiency of semitransparent Pb-Sn cells from 15.6 to 19.4%, enabling fabrication of efficient bifacial all-perovskite tandem devices.

14 SOLAR ENERGY↗

Investigation of the Interactions Between Low-Temperature Ag Paste Components and SiO2/Poly-Si(n) Contacts and the Impact on Contact Properties

Reducing poly-Si thickness to minimize parasitic absorption on a light-receiving side of a TOPCon solar cell without suffering voltage losses after metallization is a challenge in optimizing TOPCon performance. As an alternative to fire-through pastes, we investigate low-temperature Ag paste to SiO2/poly-Si passivating contacts through fabrication of electrical test structures to characterize the passivation quality and electrical transport across the metallized interface. With current paste chemistries, we find that solvent wetting of the poly-Si surface before evaporation and non-volatile binder resin adhesion to the surface after curing are major impediments which prevent Ag contact formation. However, low- resistance poly-Si/Ag interfaces formed with physical vapour deposition similarly degrade after annealing, indicating contacting issues related to the Ag content even in the absence of the organic paste components.

low temperature Ag paste↗

Defect engineering in wide-bandgap perovskites for efficient perovskite–silicon tandem solar cells

Wide-bandgap (WBG) mixed-halide perovskites show promise of realizing efficient tandem solar cells but at present suffer from large open-circuit voltage loss and the mechanism is still unclear. Here we show that WBG perovskites with iodide–bromide compositions have an increased concentration of deep traps induced by iodide interstitials, which limits performance of WBG perovskite cells. We employ tribromide ions to suppress the iodide interstitial formation and thus reduce charge recombination in bladed WBG perovskite films of Cs 0.1 FA 0.2 MA 0.7 Pb(I 0.85 Br 0.15 )3. The 1-µm-thick opaque WBG perovskite solar cells have an efficiency of 21.9%, a small open-circuit voltage deficit of 0.40 V and a large fill factor of 83%. The efficiency of the best-performing monolithic perovskite–silicon tandem cell using this perovskite reaches 28.6%. Furthermore, the tribromide addition also suppresses light-induced phase segregation in WBG perovskites and thus enhance device stability. Encapsulated tandem cells maintain 93% of their initial efficiency after operation for 550 h.

14 SOLAR ENERGY↗

Amorphous silicon carbide high contrast gratings as highly efficient spectrally selective visible reflectors

We report spectrally selective visible wavelength reflectors using hydrogenated amorphous silicon carbide (a-SiC:H) as a high index contrast material. Beyond 610nm and through the near infrared spectrum, a-SiC:H exhibits very low loss and exhibits an wavelength averaged index of refraction of n = 3.1. Here we design, fabricate, and characterize such visible reflectors using a hexagonal array of a-SiC:H nanopillars as wavelength-selective mirrors with a stop-band of approximately 40 nm full-width at half maximum. The fabricated high contrast grating exhibits reflectivity R >94% at a resonance wavelength of 642nm with a single layer of a-SiC:H nanopillars. The resonance wavelength is tunable by adjusting the geometrical parameters of the a-SiC:H nanopillar array, and we observe a stop-band spectral center shift from 635 nm up to 642 nm. High contrast gratings formed from a-SiC:H nanopillars are a promising platform for various visible wavelength nanophotonics applications.

Bauser, Haley C.↗

Self-Aligned Selective Area Front Contacts on Poly -Si/SiO x Passivating Contact c -Si Solar Cells

We report both polarity poly-Si/SiO x passivating contacts in a front/back device configuration may represent the next solar cell architecture after tunnel oxide passivating contacts (TOPCon) cells, but high parasitic absorption in the front poly -Si layer often limits its performance. This work explores a wet etching technique to remove the front poly -Si in the nonmetallized regions using self-aligned metal grids as an etch mask. We systematically examine various dielectric layers (SiN x ,Al 2 O 3 , and stacks thereof) to study the repassivation of the etched n + surface, and find that an SiN x /Al 2 O 3 passivation stack can effectively repassivate the etched surface, which we attribute to field-effect passivation from the positive fixed charge from the SiN x layer, and excellent chemical passivation property from Al 2 O 3 in the form of atomic H. We demonstrate a front/back poly-Si/SiO x passivating contact device, with an open-circuit voltage (V oc ) of 690 mV, short-circuit current density (J sc ) of 39.8 mA/cm 2 , fill factor of 78%, and power conversion efficiency of 21.4%. Furthermore, simulations using SunSolve and Quokka 3 show good agreement with both the optical and electrical properties of the experimental device. The power loss analysis reveals improvements in the optical loss from the back Ti adhesion and front SiN x layers would lead to a 23.5% device. Lastly, a techno-economic model compares the production cost of this improved cell with the current TOPCon cells. Our results highlight that further cost reductions in single-sided doped poly -Si layers are needed to compete with mainstream passivated emitter and rear cell, and TOPCon technologies.

14 SOLAR ENERGY↗

Understanding What Limits the Voltage of Polycrystalline CdSeTe Solar Cells

The origin of voltage deficits in polycrystalline cadmium selenide telluride (CdSeTe) solar cells is unclear. Here, we present a comprehensive voltage loss analysis performed on state-of-the-art CdSeTe devices - fabricated at Colorado State University and First Solar - using photoluminescence techniques, including external radiative efficiency (ERE) measurements. More specifically, we report the thermodynamic voltage limit Voc,ideal, internal voltage iVoc and external voltage Voc of partially and fully finished cells fabricated with different dopant species, dopant concentrations and back contacts. Arsenic-doped aluminium-oxide-passivated cells made at Colorado State University present remarkably high ERE (>1%) - translating into iVoc above 970 mV - but suffer from poor back-contact selectivity. On the other hand, arsenic-doped devices from First Solar present almost perfect carrier selectivity (Voc=iVoc), leading to Voc above 840 mV, and are limited by recombination in various parts of the device. Thus, development of contact structures that are both passivating and selective in combination with highly luminescent absorbers is key to reducing voltage losses.

CdSeTe devices↗

Monocrystalline 1.7-eV MgCdTe solar cells

Monocrystalline 1.7-eV Mg 0.13 Cd 0.87 Te/Mg x Cd 1-x Te (x > 0.13) double-heterostructure (DH) solar cells with varying Mg composition in the barrier layers are grown by molecular beam epitaxy. Furthermore, a Mg 0.13 Cd 0.87 Te/Mg 0.37 Cd 0.63 Te DH solar cell featuring abrupt interfaces between barriers and absorber and the addition of a SiO 2 anti-reflective coating demonstrates open-circuit voltage (V OC ), short-circuit current density (J SC ), fill factor (FF), and device active-area efficiencies up to 1.129 V, 17.3 mA/cm 2 , 77.7% and 15.2%, respectively. The V OC and FF vary oppositely with the Mg x Cd 1-x Te barrier height indicating an optimal design of the MgCdTe DHs as a tradeoff between carrier confinement and carrier transport. Temperature-dependent V OC measurements reveal the majority of carrier recombination in the devices occurs outside the DHs, in the a-Si:H hole-contact layer and at the interface between the a-Si:H layer and the Mg x Cd 1-x Te top barrier at room temperature. Simulation results for the device with the highest efficiency show that the p-type a-Si:H layer and Mg 0.37 Cd 0.63 Te top barrier contribute 1.3 mA/cm 2 and 2.4 mA/cm 2 J SC loss, respectively.

14 SOLAR ENERGY↗

Reducing sputter induced stress and damage for efficient perovskite/silicon tandem solar cells

Reducing damages caused by sputtering of transparent conductive oxide (TCO) electrodes is critical in achieving highly efficient and stable perovskite/silicon tandem solar cells. Here we study the sputter caused damage to bathocuproine (BCP), which is widely used in highly efficient p-i-n structure single junction perovskite solar cells. While BCP buffer layer protects the underneath layers from damage, itself can be damaged by sputtering of TCOs at a wide range of target-substrate distances, supported by molecular dynamic simulation. More intriguingly, it is observed that TCO easily peeled off after sputtering when the sputtering target is close to substrate. This is ascribed to formation of stress during cooling down process after sputtering due to different thermal expansion coefficients of the layers. Our studies explain why tin oxide (SnO2) made by atomic layer deposition can replace BCP for a much better tandem device performance. SnO2 has high affinity with sputtered TCO electrode to suppress peeling-off issue and has higher bond energy to resist sputter induced damage, thus it allows a wider window of target-substrate distances than BCP during TCO sputtering. Ultimately, we demonstrate an efficient perovskite/silicon monolithic tandem solar cell with efficiency of 26.0% to illustrate the beneficial effects of reduced stress and damage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sub-Bandgap Features in CdSeTe Solar Cells: Parsing the Roles of Material Properties and Cell Optics

In this contribution, we investigate why different dopant species and back-contact architectures lead to different sub-bandgap behaviors in CdSeTe solar cells. Through extraction of the absorptance from photoluminescence spectra, we parse the contributions from material properties and from cell optics. We show that, as expected, arsenic doping leads to an increase in sub-bandgap features over traditional copper doping, and that this is a material property of arsenic-doped CdSeTe. Conversely, the increase in sub-bandgap absorption and emission using alternative back contact architectures can be attributed to the cell optics, and more specifically to the increased reflectance of the back interface, leading to at least a doubling of the pathlength for sub-bandgap photons.

arsenic doping↗

Investigation of the Selectivity of Carrier Transport Layers in Wide-Bandgap Perovskite Solar Cells

Excellent contact passivation and selectivity are prerequisites to realize the full potential of high-material-quality perovskite solar cells, first to maximize the internal voltage (or quasi-Fermi-level separation) iV within the absorber, then to translate this high internal voltage into a high external voltage V. Experimental quantification of contact passivation and selectivity is, thus, key to improving device performance. Here, open-circuit measurements of iV oc and V oc , combined with surface photovoltage measurements, are used to systematically quantify the passivation—using iVoc as a metric—and the selectivity—defined as Soc=V oc /iV oc —of a range of common carrier transport layers to wide-bandgap (1.67 eV) perovskite absorbers. The resulting solar cells suffer from large voltage deficits, particularly when NiO x is used as the hole transport layer, even though it provides better passivation than its polymer-based counterparts (PTAA and PTAA/PFN). This indicates a poor selectivity of NiO x (Soc<0.81 for NiO x -based devices), whereas devices using polymer-based hole transport layers exhibit high selectivity (S oc =0.94–0.95). In agreement with recent reports, this low selectivity is attributed to the formation of an interlayer of non-perovskite material with high resistance to holes at the perovskite/NiO x interface. These measurements also imply that the selectivity of the C60-based electron transport layers is relatively good.

carrier transport layers↗

Thermal model to quantify the impact of sub-bandgap reflectance on operating temperature of fielded PV modules

Minimizing module heating is an effective way to increase the lifetime energy output of photovoltaic systems. Maximizing the reflection of light that is unusable for energy conversion is one of the most promising ways to reduce the operating temperature of fielded modules. We derive a model based on a steady-state energy balance to quantify the temperature benefit of cell or module optical modifications aimed at improving reflection of light with photon energies below the photovoltaic cell bandgap energy. This more detailed model is then simplified so that, from outdoor measured data, temperature differences arising from reflectance can be isolated from those arising from irradiance, wind speed, and module standard-test-condition efficiency.

14 SOLAR ENERGY↗

World Record Demonstration of > 30% Thermophotovoltaic Conversion Efficiency

Thermophotovoltaic (TPV) devices are solid-state heat engines that convert thermal radiation into electricity using semiconductor diodes, and have applications in energy storage, primary power conversion, and waste heat recovery. Higher temperature emitters and wider band gap photovoltaics (PVs) generally afford higher TPV efficiencies. High temperature emitters are accessible in thermal energy storage applications. We have demonstrated a world record 31% +/- 2% TPV conversion efficiency with a 0.9 cm2 GaAs-based PV device under a 2430 °C thermal emitter, producing an electrical output power of 2.23 W. Critical to the result was the cell’s high reflectance of photon energies below the device band gap. Unlike solar PV, for which sub-band gap (SBG) light is lost, a TPV cell can reflect and recycle SBG light to the thermal emitter. The demonstration was made on a custom-built measurement platform in which a ~100 cm2 graphite thermal emitter was heated under vacuum up to 2430 °C. The TPV efficiency was evaluated by comparing the measured electrical output power of the TPV with the calorimetrically measured total net power incident on the cell. The measured TPV efficiency as a function of thermal emitter temperature was corroborated by our full system modeling predictions. As far as the authors are aware, this is the highest TPV conversion efficiency ever measured, and device improvements should yield > 40% efficiency in the near future.

27 ARPA - Advanced Research Projects Agency-Energy↗

Sub-micrometer random-pyramid texturing of silicon solar wafers with excellent surface passivation and low reflectance

Select emerging solar cell technologies, ranging from very narrow screen-printed fingers to perovskite/silicon tandems, would benefit from a reduction of the height of the standard pyramidal texture of monocrystalline silicon wafers to below 1 μm. However, fabricating such small surface features usually compromises the requisite low reflectance and high passivation quality. Through systematic design of experiments, we demonstrate that conventional alkaline-based wet-chemical etching processes can be tuned to produce dense, spatially homogeneous, and uniformly sized sub-micrometer pyramids. Precise texture size can be further controlled by adding potassium silicate to the texturing solution to effectively slow the pyramid growth rate and promote nucleation. With pyramid size distribution data—extracted from multiple atomic force microscopy images across each wafer—we demonstrate 16 nanotextures with average pyramid sizes ranging from 62 to 512 nm, with the largest having only 0.3% of its pyramids taller than 1 μm. Six of the nanotextures exhibit light trapping and surface defect densities comparable to state-of-the-art microtextured wafers. In conclusion, the best nanotexture achieved an AM1.5G-weighted reflectance of 11.8% and a minority-carrier lifetime of 3.4 ms after passivation with amorphous silicon, demonstrating that smaller textures need not deteriorate solar cell performance.

14 SOLAR ENERGY↗