Engineering topics

Hopson, Purnell, Jr.

Publications and source records attributed to Hopson, Purnell, Jr..

10 records

NASA NTRS2001

Multi-Channel Electronically Scanned Cryogenic Pressure Sensor And Method For Making Same

A miniature, multi-channel, electronically scanned pressure measuring device uses electrostatically bonded silicon dies in a multi-element array. These dies are bonded at specific sites on a glass, pre-patterned substrate. Thermal data is multiplexed and recorded on each individual pressure measuring diaphragm. The device functions in a cryogenic environment without the need of heaters to keep the sensor at constant temperatures.

Chapman, John J.↗

NASA NTRS2000

Method of Forming Micro-Sensor Thin-Film Anemometer

A device for measuring turbulence in high-speed flows is provided which includes a micro- sensor thin-film probe. The probe is formed from a single crystal of aluminum oxide having a 14 deg half-wedge shaped portion. The tip of the half-wedge is rounded and has a thin-film sensor attached along the stagnation line. The bottom surface of the half-wedge is tilted upward to relieve shock induced disturbances created by the curved tip of the half-wedge. The sensor is applied using a microphotolithography technique.

Sheplak, Mark↗

NASA NTRS1998

Assembly and Integration of Superconductive Measurement Circuits for a Spaceflight Experiment

Hybrid microelectronics containing both conventional electronic components and high-temperature superconductive films have been designed, fabricated, and tested. The devices operate from room temperature to 75K and perform d.c. four-probe resistance measurements on six superconductive specimens resident on each circuit. Four of these hybrid circuits were incorporated into the Materials In Devices As Superconductors (MIDAS) spaceflight experiment and evaluated over a 90-day period on the Mir space station. Prior to launch, comprehensive testing of the flight circuits was performed to determine the effects of thermal cycling, vibration loads, and long-term operation on circuit performance. This report describes the fabrication and assembly procedures used to produce the hybrid circuits, the techniques used to integrate the circuits into the MIDAS hardware system, and the results of pre-flight evaluations which verified circuit functionality.

Wise, Stephanie A.↗

NASA NTRS1995

Multi-channel electronically scanned cryogenic pressure sensor

A miniature, multi-channel, electronically scanned pressure measuring device uses electrostatically bonded silicon dies in a multielement array. These dies are bonded at specific sites on a glass, prepatterned substrate. Thermal data is multiplexed and recorded on each individual pressure measuring diaphragm. The device functions in a cryogenic environment without the need of heaters to keep the sensor at constant temperatures.

Chapman, John J.↗

NASA NTRS1994

Micro-sensor thin-film anemometer

A device for measuring turbulence in high-speed flows is provided which includes a micro-sensor thin-film probe. The probe is formed from a single crystal of aluminum oxide having a 14 deg half-wedge shaped portion. The tip of the half-wedge is rounded and has a thin-film sensor attached along the stagnation line. The bottom surface of the half-wedge is tilted upward to relieve shock induced disturbances created by the curved tip of the half-wedge. The sensor is applied using a microphotolithography technique.

Sheplak, Mark↗

NASA NTRS1994

Cryogenic Multichannel Pressure Sensor With Electronic Scanning

Array of pressure sensors operates reliably and repeatably over wide temperature range, extending from normal boiling point of water down to boiling point of nitrogen. Sensors accurate and repeat to within 0.1 percent. Operate for 12 months without need for recalibration. Array scanned electronically, sensor readings multiplexed and sent to desktop computer for processing and storage. Used to measure distributions of pressure in research on boundary layers at high Reynolds numbers, achieved by low temperatures.

Hopson, Purnell, Jr.↗

NASA NTRS1992

High temperature fiber optic microphone having a pressure-sensing reflective membrane under tensile stress

A fiber optic microphone is provided for measuring fluctuating pressures. An optical fiber probe having at least one transmitting fiber for transmitting light to a pressure-sensing membrane and at least one receiving fiber for receiving light reflected from a stretched membrane is provided. The pressure-sensing membrane may be stretched for high frequency response. Further, a reflecting surface of the pressure-sensing membrane may have dimensions which substantially correspond to dimensions of a cross section of the optical fiber probe. Further, the fiber optic microphone can be made of materials for use in high temperature environments, for example greater than 1000 F. A fiber optic probe is also provided with a backplate for damping membrane motion. The backplate further provides a means for on-line calibration of the microphone.

Zuckerwar, Allan J.↗

NASA NTRS1990

Dielectric Coating For Hot-Film Flow Sensors

Very-thin-film dielectric coating stable over range of temperatures developed. This dielectric coating, combination of fused silica and thermoplastic polymer, has sufficient stability to withstand stresses placed upon it by cycling to and from cryogenic temperatures. Coating tailored to meet almost any criterion of roughness height. Useful for research in application of hot-film sensors to airfoils.

Hopson, Purnell, Jr.↗

NASA NTRS1990

Method of forming a multiple layer dielectric and a hot film sensor therewith

The invention is a method of forming a multiple layer dielectric for use in a hot-film laminar separation sensor. The multiple layer dielectric substrate is formed by depositing a first layer of a thermoelastic polymer such as on an electrically conductive substrate such as the metal surface of a model to be tested under cryogenic conditions and high Reynolds numbers. Next, a second dielectric layer of fused silica is formed on the first dielectric layer of thermoplastic polymer. A resistive metal film is deposited on selected areas of the multiple layer dielectric substrate to form one or more hot-film sensor elements to which aluminum electrical circuits deposited upon the multiple layered dielectric substrate are connected.

Hopson, Purnell, Jr.↗

NASA NTRS1987

Status of a specialized boundary layer transition detection system for use in the U.S. National Transonic Facility

An improved deposition technique for cryogenic hot films used for transition detection in cryogenic tunnels is reported. Tests of the hot films in a low-speed tunnel demonstrated the ability to obtain online transition data. The capability of an enhanced hot film data acquisition system was also demonstrated. A comparison of data from the new system with stability theory shows the detection of Tollmein-Schlicting waves at transition onset.

Johnson, Charles B.↗