Search NASA⌕ Search

Engineering topics

Iles, P.

Publications and source records attributed to Iles, P..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

34% Efficient InGaP/GaAs/GaSb Cell-Interconnected-Circuits for Line-Focus Concentrator Arrays

While monolithic multi-junction cells are preferred for flat plate arrays, mechanically stacked multi-junction cells are superior for solar concentrator applications. Reasons for this are that the mechanical stacked configuration with high efficiency Gallium Antimonide cells allows utilization of a much wider range of the solar energy spectrum, and the ability to use voltage matched interconnects results in full use of low bandgap cell currents. Herein, data are presented for simple two terminal voltage-matched circuits using InGaP/GaAs/GaSb stacked cells showing 34% average circuit efficiency for a lot of 12 circuits given prismatic covers. These circuits have been designed to fit into the ultralight Stretched Lens Array being developed by NASA. With these new cell-interconnected-circuits, we project that the power density at GEO operating temperature can be increased from 296 W/m2 to 350 W/m2 while maintaining the specific power at 190 W/kg at the full wing level.

Fraas, L. M.↗
NASA NTRS1982

Interaction between cast silicon properties and solar cell performance

Three types of cast silicon, Silso, HEM (Heat-Exchanger Method) and UCP (Ubiquitous Crystallization Process) were studied for their use as solar cells. Optical microscopy after etching revealed a high density of uniform dislocations (approaching 1,000,000/sq cm), lines of dislocations indicating stress during crystal growth, and precipitates, some of which generate dislocations. Solar cells were fabricated by three processes. Results of solar cell processing revealed that these materials produce cells of lower efficiency than Czochralski control cells, and that the efficiencies of the three materials were quite close. Diffusion length and spectral response data are shown. Certain structural features are correlated with solar cell efficiency, diffusion length, and spectral response. Electron-beam induced current (EBIC) and light spot scanning are used to back up other measurements.

Hyland, S.↗
NASA NTRS1981

Diagnostic study of BSF silicon solar cells

Solar cells equipped with back surface fields (BSF) were fabricated by means of an aluminum alloy, boron diffusion, and boron ion implantation. The importance of initial thickness, resistivity, orientation, and the crystal growth method were examined. Aluminum in paste form was screen printed on the cell, followed by alloy formation at 800 C for a minute. Application of the BSFs resulted in open circuit voltage improvements dependent on the substrate resistivity, ranging from 10 mV at 0.3 ohm-cm to 50 mV at 15 ohm-cm. The gains in performance were attributed to a longer penetration depth, a heightened concentration profile at the interface, and higher concentrations in the p+ layer.

Yoo, H.↗
NASA NTRS1980

Evaluation and optimization of silicon sheet solar cells

This paper describes the results and procedures to evaluate and improve the efficiency of solar cells made from various unconventional silicon sheets. The performance parameters included photovoltaic characteristics, spectral response, dark I-V characteristics, and diffusion length. The evaluation techniques used provided accurate and reliable information on sheet performance, and self-consistent results were obtained from the various measurement techniques used. Minority carrier diffusion length (L) was shown to be the ultimate limiting factor for the sheet cell performance (efficiency) and other back-up measurements confirmed this L-dependence. Limited efforts were made to identify defects which influence cell performance, and to use some improved process methods to increase cell efficiency.

Yoo, H.↗
NASA NTRS1980

Opto-electronic properties of cells made from various silicon forms

Opto-electronic properties of the various silicon forms were obtained from the solar cell performance. Performance parameters included the photovoltaic characteristics, minority carrier diffusion length, spectral response and small light spot scanning. Self consistent results were obtained from the various measurement techniques, which can provide useful information on sheet quality, as a potential for low cost terrestrial applications, and areas where the sheet formation methods can be improved.

Yoo, H.↗
NASA NTRS1977

Production of large "violet" solar cells

Devices respond better to ultraviolet radiation than conventional cells and respond better over whole visible spectrum. Response is improved because of very shallow (0.1 micrometer) highly doped n(+) layer diffused into P silicon.

Iles, P.↗