Search NASA⌕ Search

Engineering topics

Innis, R. C.

Publications and source records attributed to Innis, R. C..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

A flight study of the use of direct-lift-control flaps to improve station keeping during in-flight refueling

To investigate the effectiveness of fast-acting flaps as direct-lift-control (DLC) devices on a fighter airplane, the aileron servo systems of an F-100C variable-stability airplane were modified to provide symmetrical actuation of the surfaces. Initial flight tests using DLC indicated that the task of formation flying and, hence, in-flight refueling could be eased by actuating the DLC flaps through the conventional control stick, with the degree of improvement depending on the basic stability of the receiver aircraft. Results of refueling approaches and connections with U.S. Air Force tankers indicated a moderate overall improvement in vertical station-keeping performance (approximately 19 percent) and a sizeable overall decrease in receiver airplane motions and control activity (approximately 40 percent) with DLC.

Mcneill, W. E.↗
NASA NTRS1972

Pitch attitude, flight path, and airspeed control during approach and landing of a powered lift STOL aircraft

Analytical investigations and piloted moving base simulator evaluations were conducted for manual control of pitch attitude, flight path, and airspeed for the approach and landing of a powered lift jet STOL aircraft. Flight path and speed response characteristics were described analytically and were evaluated for the simulation experiments which were carried out on a large motion simulator. The response characteristics were selected and evaluated for a specified path and speed control technique. These charcteristics were: (1) the initial pitch response and steady pitch rate sensitivity for control of attitude with a pitch rate command/ attitude hold system, (2) the initial flight path response, flight path overshoot, and flight path-airspeed coupling in response to a change in thrust, and (3) the sensitivity of airspeed to pitch attitude changes. Results are presented in the form of pilot opinion ratings and commentary, substantiated where appropriate by response time histories and aircraft states at the point of touchdown.

Franklin, J. A.↗
NASA NTRS1972

A flight evaluation of VTOL jet transport under visual and simulated instrument conditions

A flight investigation was performed with the Dornier DO-31 VTOL to evaluate the performance, handling qualities, and operating characteristics that are considered to be important in the operation of a commerical VTOL transport in the terminal area. The DO-31, a 20,000 kilogram transport, has a mixed jet propulsion system; main engines with nozzles deflect from a cruise to a hover position, and vertical lift engines operated below 170 knots. This VTOL mode incorporates pitch and roll attitude and yaw rate stabilization. The tests concentrated on the transition, approach, and vertical landing. The mixed jet propulsion system provided a large usable performance envelope that enabled simulated IFR approaches to be made on 7 deg and 12 deg glide slopes. In these approaches management of thrust magnitude and direction was a primary problem, and some form of integrating the controls will be necessary. The handling qualities evaluation pointed out the need for additional research of define flight path criteria. The aircraft had satisfactory control and stability in hover out of ground effect. The recirculation effects in vertical landing were large below 15 meters.

Holzhauser, C. A.↗
NASA NTRS1972

Longitudinal handling qualities during approach and landing of a powered lift STOL aircraft

Longitudinal handling qualities evaluations were conducted on the Ames Research Center Flight Simulator for Advanced Aircraft (FSAA) for the approach and landing tasks of a powered lift STOL research aircraft. The test vehicle was a C-8A aircraft modified with a new wing incorporating internal blowing over an augmentor flap. The investigation included: (1) use of various flight path and airspeed control techniques for the basic vehicle; (2) assessment of stability and command augmentation schemes for pitch attitude and airspeed control; (3) determination of the influence of longitudinal and vertical force coupling for the power control; (4) determination of the influence of pitch axis coupling with the thrust vector control; and (5) evaluations of the contribution of stability and command augmentation to recovery from a single engine failure. Results are presented in the form of pilot ratings and commentary substantiated by landing approach time histories.

Franklin, J. A.↗
NASA NTRS1972

Flight-path and airspeed control for the STOL approach and landing

Analytical investigations and piloted moving base simulator evaluations were conducted for manual control of flight path and airspeed for the approach and landing of a powered lift jet STOL aircraft. Flight-path and airspeed response characteristics were described analytically and were evaluated for the simulation experiments which were carried out on a large motion simulator. The response characteristics were selected and evaluated for a specified path and speed control technique. These characteristics were the initial flight-path response, flight-path overshoot, flight-path-airspeed coupling in response to a change in thrust, and the sensitivity of airspeed to pitch-attitude changes. Results are presented in the form of pilot opinion ratings and commentary, substantiated where appropriate by response time histories and aircraft states at the point of touchdown.

Franklin, J. A.↗
NASA NTRS1972

Comparisons of simulator and flight results on augmentor-wing jet STOL research aircraft

The considerations involved in making a piloted simulator an effective research tool in the design and development of new aircraft are discussed. An assessment of the limitations of the simulator in depicting real flight as well as the problem of recognizing erroneous results when the simulator is supplied with incorrect input data is made. Examples of the ways in which the simulator is used to design and develop the augmentor-wing aircraft are presented. Four areas of investigation are: (1) to design the lateral control system for proper feel and response, (2) determine the effect of engine failure during approach, (3) develop the best technique for controlling flight path during approach, and (4) the significance of lift loss in ground effect and how to compensate for such loss.

Innis, R. C.↗