Engineering topics

Jackson, J. R.

Publications and source records attributed to Jackson, J. R..

7 records

NASA NTRS2020

Repair of Sandwich Structure in Support of the Payload Adapter Fitting (PAF) Part II: Severe Damage Repair

As part of a program examining a Payload Adaptor Fitting (PAF) for NASA’s Space Launch System (SLS), a repair study of impact damage and misdrilled holes in composite sandwich structure was undertaken.1 In that study, it was shown that small holes and barely visible impact damage (BVID) could be repaired and all the measured undamaged in-plane compression strength recovered without removing the damaged material using a simple patch repair. It was noted that for more severe damage, either larger patches or removal of damage (or both) may be necessary to regain all of the measured undamaged compression strength. This Technical Memorandum (TM) presents the results of an experimental investigation into repair of more severely damaged sandwich structure than what was studied in reference 1.

Nettles, A. T.↗

NASA NTRS2018

Repair of Sandwich Structure in Support of the Payload Adapter Fitting

As part of a program examining a composite payload adaptor fitting (PAF) for NASA’s Space Launch System (SLS), a repair study of impact damage and misdrilled holes was undertaken. At the beginning of this repair study, the PAF was baselined as a honeycomb sandwich structure with eight-ply quasi-isotropic, carbon-fiber-reinforced epoxy facesheets. Although the baseline configuration could change, the repair program presented herein is generic enough in nature such that it will apply to most sandwich configurations. The vast majority of loads experienced by this structure will be in-plane compression; thus, this repair study concentrates on the in-plane compression strength of representative sandwich structure specimens. The PAF is a truncated cone with a minimum diameter of about 170 inches at the top and a maximum diameter of about 335 inches at the bottom. While the launch vehicle hardware should be protected throughout its life on the ground, rogue events (or misdrilled holes) are still a possibility. This study is not meant to address large scale damage or damage to the part other than in the acreage (the uniform portion of the structure that does not consist of joints or other detailed areas), but address the most probable type of damages (small impacts and misdrilled holes) in the vast majority of the structure (the acreage).

Nettles, A. T.↗

NASA NTRS2018

Sandwich Structure Risk Reduction in Support of the Payload Adapter Fitting

Reducing risk for utilizing honeycomb sandwich structure for the Space Launch System payload adapter fitting includes determining what parameters need to be tested for damage tolerance to ensure a safe structure. Specimen size and boundary conditions are the most practical parameters to use in damage tolerance inspection. The effect of impact over core splices and foreign object debris between the facesheet and core is assessed. Effects of enhanced damage tolerance by applying an outer layer of carbon fiber woven cloth is examined. A simple repair technique for barely visible impact damage that restores all compression strength is presented.

Nettles, A. T.↗

NASA NTRS2016

Composites for Exploration Upper Stage

The Composites for Exploration Upper Stage (CEUS) was a 3-year, level III project within the Technology Demonstration Missions program of the NASA Space Technology Mission Directorate. Studies have shown that composites provide important programmatic enhancements, including reduced weight to increase capability and accelerated expansion of exploration and science mission objectives. The CEUS project was focused on technologies that best advanced innovation, infusion, and broad applications for the inclusion of composites on future large human-rated launch vehicles and spacecraft. The benefits included near- and far-term opportunities for infusion (NASA, industry/commercial, Department of Defense), demonstrated critical technologies and technically implementable evolvable innovations, and sustained Agency experience. The initial scope of the project was to advance technologies for large composite structures applicable to the Space Launch System (SLS) Exploration Upper Stage (EUS) by focusing on the affordability and technical performance of the EUS forward and aft skirts. The project was tasked to develop and demonstrate critical composite technologies with a focus on full-scale materials, design, manufacturing, and test using NASA in-house capabilities. This would have demonstrated a major advancement in confidence and matured the large-scale composite technology to a Technology Readiness Level 6. This project would, therefore, have bridged the gap for providing composite application to SLS upgrades, enabling future exploration missions.

composites↗

NASA NTRS2011

The Effects of Foam Thermal Protection System on the Damage Tolerance Characteristics of Composite Sandwich Structures for Launch Vehicles

For any structure composed of laminated composite materials, impact damage is one of the greatest risks and therefore most widely tested responses. Typically, impact damage testing and analysis assumes that a solid object comes into contact with the bare surface of the laminate (the outer ply). However, most launch vehicle structures will have a thermal protection system (TPS) covering the structure for the majority of its life. Thus, the impact response of the material with the TPS covering is the impact scenario of interest. In this study, laminates representative of the composite interstage structure for the Ares I launch vehicle were impact tested with and without the planned TPS covering, which consists of polyurethane foam. Response variables examined include maximum load of impact, damage size as detected by nondestructive evaluation techniques, and damage morphology and compression after impact strength. Results show that there is little difference between TPS covered and bare specimens, except the residual strength data is higher for TPS covered specimens.

Nettles, A. T.↗

NASA NTRS2010

Simplification of Fatigue Test Requirements for Damage Tolerance of Composite Interstage Launch Vehicle Hardware

The issue of fatigue loading of structures composed of composite materials is considered in a requirements document that is currently in place for manned launch vehicles. By taking into account the short life of these parts, coupled with design considerations, it is demonstrated that the necessary coupon level fatigue data collapse to a static case. Data from a literature review of past studies that examined compressive fatigue loading after impact and data generated from this experimental study are presented to support this finding. Damage growth, in the form of infrared thermography, was difficult to detect due to rapid degradation of compressive properties once damage growth initiated. Unrealistically high fatigue amplitudes were needed to fail 5 of 15 specimens before 10,000 cycles were reached. Since a typical vehicle structure, such as the Ares I interstage, only experiences a few cycles near limit load, it is concluded that static compression after impact (CAI) strength data will suffice for most launch vehicle structures.

Nettles, A. T.↗

NASA NTRS2009

Developing a Material Strength Design Value Based on Compression after Impact Damage for the Ares I Composite Interstage

The derivation of design values for compression after impact strength for two types of honeycomb sandwich structures are presented. The sandwich structures in this study had an aluminum core and composite laminate facesheets of either 16-ply quasi or 18-ply directional lay-ups. The results show that a simple power law curve fit to the data can be used to create A- and B-basis residual strength curves.

Nettles, A. T.↗