Search NASA⌕ Search

Engineering topics

Jalan, Bharat

Publications and source records attributed to Jalan, Bharat.

At least 19 records

Handbook of Molecular Beam Epitaxy of Oxide Materials: Epitaxial Complex Oxide Growth on Semiconductors

This chapter covers the epitaxy of complex oxides on common inorganic semiconductors. The chapter opens with an introduction, motivating the subject and highlighting key general challenges (Section 6.1). We then proceed to describe the general steps of the growth procedure in Section 6.2, which concludes with an overall discussion about trade-offs and expectation management, with an emphasis on the oxide–semiconductor interface. From there, the text describes oxide growth on the common semiconductors, starting with silicon (Section 6.3), where surface reactions and oxidation are the most challenging aspects. Oxide epitaxy on germanium is described in Section 6.4, which is a less challenging oxide growth scheme on semiconductors. Section 6.5 describes oxide epitaxy on gallium arsenide, one of the more challenging schemes, where interface stability and surface preparation pose key challenges. Finally, in Section 6.6, oxide epitaxy on gallium nitride is described, where the lattice mismatch takes the stage as the key challenge. Altogether, this chapter aims to provide the reader with the practical knowledge, tactics and strategies for oxide epitaxy on semiconductors.

Demkov, Alexander A↗

Epitaxially Grown Single-Crystalline SrTiO 3 Membranes Using a Solution-Processed, Amorphous SrCa 2 Al 2 O 6 Sacrificial Layer

Water-soluble sacrificial layers based on epitaxially-grown, single crystalline (Ca, Sr, Ba) 3 Al 2 O 6 layer are widely used for creating free-standing perovskite oxide membranes. However, obtaining these sacrificial layers with intricate stoichiometry remains a challenge, especially for molecular beam epitaxy (MBE). In this study, we demonstrate the hybrid MBE growth of epitaxial, single crystalline SrTiO 3 films using a solution processed, amorphous SrCa 2 Al 2 O 6 sacrificial layer onto SrTiO 3 (001) substrates. Prior to the growth, the oxygen plasma exposure was used to first create the crystalline SrCa 2 Al 2 O 6 layer with well-defined surface crystallinity. Utilizing reflection high energy electron diffraction, x-ray diffraction, and atomic force microscopy, we observe an atomic layer-by-layer growth of epitaxial, single crystalline SrTiO 3 film on the SrCa 2 Al 2 O 6 layer with atomically smooth surfaces. The SrCa 2 Al 2 O6 layer was subsequently dissolved in de-ionized water to create free-standing SrTiO3 membranes that were transferred onto a metal-coated Si wafer. Membranes created with Sr-deficiency revealed ferroelectric-like behavior measured using piezo force microscopy whereas stoichiometric films remained paraelectric-like. Furthermore, these findings underscore the viability of using ex-situ deposited amorphous SrCa2Al2O6 for epitaxial, single crystalline growth, as well as the importance of point defects in determining the ferroic properties in membranes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Anomalous frequency and temperature dependent scattering in the dilute metallic phase in lightly doped-SrTiO 3

The mechanism of superconductivity in materials with aborted ferroelectricity and its emergence out of a dilute metallic phase in systems like doped-SrTiO 3 is an outstanding issue in condensed matter physics. This dilute metal has anomalous properties that are both similar and different to those found in the normal state of other unconventional superconductors. For instance, T 2 resistivity can be found at densities that are too small to allow current decay through electronelectron scattering. We have investigated the optical properties of the dilute metallic phase in doped-SrTiO 3 using THz time-domain spectroscopy. At low frequencies the THz response exhibits a Drude-like form as expected for typical metal-like conductivity. We observed the frequency and temperature dependencies to the low energy scattering rate Γ(ω, T) ∝ (¯hω) 2 + (pπk B T) 2 expected in a conventional Fermi liquid. However we find the lowest known p values of 0.39-0.72. As p is 2 in a canonical Fermi liquid and existing models based on energy dependent elastic scattering bound p from below to 1, our observation lies outside current explanation. Our data also gives insight into the high temperature regime and shows that the temperature dependence of the resistivity derives in part from strong T dependent mass renormalizations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Hybrid Molecular Beam Epitaxy for Single-Crystalline Oxide Membranes with Binary Oxide Sacrificial Layers

The advancement in thin-film exfoliation for synthesizing oxide membranes has led to possibilities for creating artificially assembled heterostructures with structurally and chemically incompatible materials. The sacrificial layer method is a promising approach to exfoliate as-grown films from a compatible material system, allowing for their integration with dissimilar materials. Nonetheless, the conventional sacrificial layers often possess an intricate stoichiometry, thereby constraining their practicality and adaptability, particularly when considering techniques such as molecular beam epitaxy (MBE). This is where easy-to-grow binary alkaline-earth-metal oxides with a rock salt crystal structure are useful. These oxides, which include (Mg, Ca, Sr, Ba)O, can be used as a sacrificial layer covering a much broader range of lattice parameters compared to conventional sacrificial layers and are easily dissolvable in deionized water. In this study, we show the epitaxial growth of the single-crystalline perovskite SrTiO 3 (STO) on sacrificial layers consisting of crystalline SrO, BaO, and Ba 1–x Ca x O films, employing a hybrid MBE method. Our results highlight the rapid (≤5 min) dissolution of the sacrificial layer when immersed in deionized water, facilitating the fabrication of millimeter-sized STO membranes. Using high-resolution X-ray diffraction, atomic-force microscopy, scanning transmission electron microscopy, impedance spectroscopy, and scattering-type near-field optical microscopy (SNOM), we demonstrate single-crystalline STO membranes with bulk-like intrinsic dielectric properties. The employment of alkaline earth metal oxides as sacrificial layers is likely to simplify membrane synthesis, particularly with MBE, thus expanding the research and application possibilities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Pt vacancies on magnetotransport of Weyl semimetal candidate GdPtSb epitaxial films

Here, we examine the effects of Pt vacancies on the magnetotransport properties of Weyl semimetal candidate GdPtSb films, grown by molecular beam epitaxy on c-plane sapphire. Rutherford backscattering spectrometry and x-ray diffraction measurements suggest that phase-pure GdPt x ⁢Sb films can accommodate up to 15% of Pt vacancies (x = 0.85), which act as acceptors, as measured by the Hall effect. Two classes of electrical transport behavior are observed. Pt-deficient films display metallic temperature-dependent resistivity (dρ/dT > 0). The longitudinal magnetoresistance (LMR, magnetic field B parallel to electric field E) is more negative than transverse magnetoresistance (TMR, B⁢⊥⁢E), consistent with the expected chiral anomaly for a Weyl semimetal. The combination of Pt-vacancy disorder and doping away from the expected Weyl nodes, however, suggests that conductivity fluctuations may explain the negative LMR rather than chiral anomaly. Samples closer to stoichiometry display the opposite behavior: semiconductorlike resistivity (dρ/dT > 0) and more negative TMR than LMR. Hysteresis and other nonlinearities in the low-field Hall effect and magnetoresistance suggest that spin-disorder scattering and possible topological Hall effect may dominate the near-stoichiometric samples. Our findings highlight the complications of transport-based identification of Weyl nodes but point to possible topological spin textures in GdPtSb.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Engineering metal oxidation using epitaxial strain

The oxides of platinum group metals are promising for future electronics and spintronics due to the delicate interplay of spin-orbit coupling and electron correlation energies. However, their synthesis as thin films remains challenging due to their low vapour pressures and low oxidation potentials. Here we show how epitaxial strain can be used as a control knob to enhance metal oxidation. Using Ir as an example, we demonstrate the use of epitaxial strain in engineering its oxidation chemistry, enabling phase-pure Ir or IrO 2 films despite using identical growth conditions. The observations are explained using a density-functional-theory-based modified formation enthalpy framework, which highlights the important role of metal-substrate epitaxial strain in governing the oxide formation enthalpy. We also validate the generality of this principle by demonstrating epitaxial strain effect on Ru oxidation. The IrO 2 films studied in our work further revealed quantum oscillations, attesting to the excellent film quality. The epitaxial strain approach we present could enable growth of oxide films of hard-to-oxidize elements using strain engineering.

36 MATERIALS SCIENCE↗

Sn-modified BaTiO 3 thin film with enhanced polarization

Hybrid molecular beam epitaxy (MBE) growth of Sn-modified BaTiO 3 films was realized with varying domain structures and crystal symmetries across the entire composition space. Macroscopic and microscopic structures and the crystal symmetry of these thin films were determined using a combination of optical second harmonic generation (SHG) polarimetry and scanning transmission electron microscopy (STEM). SHG polarimetry revealed a variation in the global crystal symmetry of the films from tetragonal (P4mm) to cubic (PM3¯m) across the composition range, x = 0 to 1 in BaTi 1–x Sn x O 3 (BTSO). STEM imaging shows that the long-range polar order observed when the Sn content is low (x = 0.09) transformed to a short-range polar order as the Sn content increased (x = 0.48). Consistent with atomic displacement measurements from STEM, the largest polarization was obtained at the lowest Sn content of x = 0.09 in Sn-modified BaTiO 3 as determined by SHG. Furthermore, these results agree with recent bulk ceramic reports and further identify this material system as a potential replacement for Pb-containing relaxor-based thin film devices.

36 MATERIALS SCIENCE↗

Freestanding epitaxial SrTiO 3 nanomembranes via remote epitaxy using hybrid molecular beam epitaxy

The epitaxial growth of functional oxides using a substrate with a graphene layer is a highly desirable method for improving structural quality and obtaining freestanding epitaxial nanomembranes for scientific study, applications, and economical reuse of substrates. However, the aggressive oxidizing conditions typically used in growing epitaxial oxides can damage graphene. Here, we demonstrate the successful use of hybrid molecular beam epitaxy for SrTiO 3 growth that does not require an independent oxygen source, thus avoiding graphene damage. This approach produces epitaxial films with self-regulating cation stoichiometry. Furthermore, the film (46-nm-thick SrTiO 3 ) can be exfoliated and transferred to foreign substrates. These results open the door to future studies of previously unattainable freestanding oxide nanomembranes grown in an adsorption-controlled manner by hybrid molecular beam epitaxy. This approach has potentially important implications for the commercial application of perovskite oxides in flexible electronics and as a dielectric in van der Waals thin-film electronics.

36 MATERIALS SCIENCE↗

Transient electron scavengers modulate carrier density at a polar/nonpolar perovskite oxide heterojunction

Here, we show how transient electron scavengers can be utilized to control the carrier concentration at polar/non-polar perovskite interfaces. By combining quantitative synchrotron x-ray-based interface structure determination with ab initio modeling, we demonstrate that Nd vacancy formation and the resulting formation of Nd adatoms, stabilized by oxygen scavengers at the growth front, can quantitatively account for the decreased carrier concentration at the SrTiO 3 /n NdTiO 3 /SrTiO 3 (001) heterojunction for n = 1 unit cell. This study yields new insights into growth mechanisms and the effect of transient species and defects on the electronic properties of oxide heterojunctions.

36 MATERIALS SCIENCE↗

Semi-metallic SrIrO 3 films using solid-source metal-organic molecular beam epitaxy

Perovskite SrIrO 3 films and its heterostructures are very promising, yet less researched, avenues to explore interesting physics originating from the interplay between strong spin–orbit coupling and electron correlations. Elemental iridium is a commonly used source for molecular beam epitaxy (MBE) synthesis of SrIrO 3 films. However, elemental iridium is extremely difficult to oxidize and evaporate while maintaining an ultra-high vacuum and a long mean free path. Here, we calculated a thermodynamic phase diagram to highlight these synthesis challenges for phase-pure SrIrO 3 and other iridium-based oxides. We addressed these challenges using a novel solid-source metal-organic MBE approach that rests on the idea of modifying the metal-source chemistry. Phase-pure, single-crystalline, coherent, epitaxial (001) pc SrIrO 3 films on (001) SrTiO 3 substrate were grown. Films demonstrated semi-metallic behavior, Kondo scattering, and weak antilocalization. Our synthesis approach has the potential to facilitate research involving iridate heterostructures by enabling their atomically precise syntheses.

36 MATERIALS SCIENCE↗

Probing electronic dead layers in homoepitaxial n-SrTiO 3 (001) films

We combine state-of-the-art oxide epitaxial growth by hybrid molecular beam epitaxy with transport, x-ray photoemission, and surface diffraction, along with classical and first-principles quantum mechanical modeling to investigate the nuances of insulating layer formation in otherwise high-mobility homoepitaxial n-SrTiO 3 (001) films. Our analysis points to charge immobilization at the buried n-SrTiO 3 /undoped SrTiO 3 (001) interface as well as within the surface contamination layer resulting from air exposure as the drivers of electronic dead-layer formation. As Fermi level equilibration occurs at the surface and the buried interface, charge trapping reduces the sheet carrier density (n 2D ) and renders the n-STO film insulating if n 2D falls below the critical value for the metal-to-insulator transition.

36 MATERIALS SCIENCE↗

Breaking $\mathrm{OER}$ and $\mathrm{CER}$ scaling relations via strain and its relaxation in $\mathrm{RuO}$ 2 (101)

Green hydrogen production from abundant water sources is an important component of renewable energy storage. Water oxidation catalysts are typically considered bound by adsorbate scaling relations, limiting their activity for the oxygen evolution reaction (OER) as well as selectivity between OER and the chlorine evolution reaction (CER) that compete in saline water streams. RuO 2 is highly active for both reactions, and recent measurements have shown the OER activity is greater on undercoordinated, high index facets compared to the lowest-energy (110) facet often studied. The growth of such orientations as epitaxial films, however, can result in appreciable strain and potential surface faceting via its relaxation. Here, we find the activity and selectivity towards OER and CER vary with thickness in epitaxial (101) RuO 2 thin films: OER activity decreases 4x as film thickness increases from 8 nm to 48 nm, while CER activity is comparable. Thus, strain and its relaxation can be used to break scaling relationships between OER and CER, highlighting the important role that defects play in selective oxidation processes on RuO 2 in chloride-containing media.

36 MATERIALS SCIENCE↗

Epitaxial SrTiO 3 films with dielectric constants exceeding 25,000

Significance Semiconductor interfaces are among the most important in use in modern technology. The properties they exhibit can either enable or disable the characteristics of the materials they connect for functional performance. While much is known about important junctions involving conventional semiconductors such as Si and GaAs, there are several unsolved mysteries surrounding interfaces between oxide semiconductors. Here we resolve a long-standing issue concerning the measurement of anomalously low dielectric constants in SrTiO 3 films with record high electron mobilities. We show that the junction between doped and undoped SrTiO 3 required to make dielectric constant measurements masks the dielectric properties of the undoped film. Through modeling, we extract the latter and show that it is much higher than previously measured.

36 MATERIALS SCIENCE↗

Preface for the special topic collection honoring Dr. Scott Chambers’ 70th birthday and his leadership in the science and technology of oxide thin films

It is an honor to dedicate this special issue to Dr. Scott A. Chambers, who has had a rewarding and impactful career in surface science, spectroscopy, and thin film synthesis. His research career, spanning from his graduate work in the 1970’s to the present day, was built upon pioneering early work in precision thin film synthesis and spectroscopic characterization that occurred beginning in the 1960’s. Notably, this includes the contributions of both Art Gossard to precision film synthesis by molecular beam epitaxy (MBE) and Chuck Fadley to photoelectron spectroscopy; both Art and Chuck were recently honored with JVSTA commemorative issues of their own. Yet Scott is no mere copycat; he extended and expanded their contributions to further advance the field of surface science, and he applied the same scientific rigor to the emerging field of precision epitaxial oxide synthesis. This rigor was perhaps not always appreciated by the more “enthusiastic” members of the community who tended to draw exciting conclusions from limited data. He was once referred to, fondly, by a collaborator as a “spoilsport” for his penchant for using careful, defensible synthesis and characterization to prove that popular models and assumptions of the day did not stand up to scrutiny.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗