Engineering topics

Johnson, Wayne

Publications and source records attributed to Johnson, Wayne.

At least 91 records · Page 5

NASA NTRS2004

Model for Vortex Ring State Influence on Rotorcraft Flight Dynamics

The influence of vortex ring state (VRS) on rotorcraft flight dynamics is investigated, specifically the vertical velocity drop of helicopters and the roll-off of tiltrotors encountering VRS. The available wind tunnel and flight test data for rotors in vortex ring state are reviewed. Test data for axial flow, nonaxial flow, two rotors, unsteadiness, and vortex ring state boundaries are described and discussed. Based on the available measured data, a VRS model is developed. The VRS model is a parametric extension of momentum theory for calculation of the mean inflow of a rotor, hence suitable for simple calculations and real-time simulations. This inflow model is primarily defined in terms of the stability boundary of the aircraft motion. Calculations of helicopter response during VRS encounter were performed, and good correlation is shown with the vertical velocity drop measured in flight tests. Calculations of tiltrotor response during VRS encounter were performed, showing the roll-off behavior characteristic of tiltrotors. Hence it is possible, using a model of the mean inflow of an isolated rotor, to explain the basic behavior of both helicopters and tiltrotors in vortex ring state.

VORTEX RING STATE↗

NASA NTRS2003

Airloads and Wake Geometry Calculations for an Isolated Tiltrotor Model in a Wind Tunnel

Th tiltrotor aircraft configuration has the potential to revolutionize air transportation by providing an economical combination of vertical take-off and landing capability with efficient, high-speed cruise flight. To achieve this potential it is necessary to have validated analytical tools that will support future tiltrotor aircraft development. These analytical tools must calculate tiltrotor aeromechanical behavior, including performance, structural loads, vibration, and aeroelastic stability, with an accuracy established by correlation with measured tiltrotor data. For many years such correlation has been performed for helicopter rotors (rotors designed for edgewise flight), but correlation activities for tiltrotors have been limited, in part by the absence of appropriate measured data. The recent test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, U4-scale V-22 rotor in the German-Dutch Wind Tunnel (DNW) now provides an extensive set of aeroacoustic, performance, and structural loads data. This paper will present calculations of airloads, wake geometry, and performance, including correlation with TRAM DNW measurements. The calculations were obtained using CAMRAD II, which is a modern rotorcraft comprehensive analysis, with advanced models intended for application to tiltrotor aircraft as well as helicopters. Comprehensive analyses have received extensive correlation with performance and loads measurements on helicopter rotors. The proposed paper is part of an initial effort to perform an equally extensive correlation with tiltrotor data. The correlation will establish the level of predictive capability achievable with current technology; identify the limitations of the current aerodynamic, wake, and structural models of tiltrotors; and lead to recommendations for research to extend tiltrotor aeromechanics analysis capability. The purpose of the Tilt Rotor Aeroacoustic Model (TRAM) experimental project is to provide data necessary to validate tiltrotor performance and aeroacoustic prediction methodologies and to investigate and demonstrate advanced civil tiltrotor technologies. The TRAM project is a key part of the NASA Short Haul Civil Tiltrotor (SHCT) project. The SHCT project is an element of the Aviation Systems Capacity Initiative within NASA. In April-May 1998 the TRAM was tested in the isolated rotor configuration at the Large Low-speed Facility of the German-Dutch Wind Tunnels (DNW). A preparatory test was conducted in December 1997. These tests were the first comprehensive aeroacoustic test for a tiltrotor, including not only noise and performance data, but airload and wake measurements as well. The TRAM can also be tested in a fill-span configuration, incorporating both rotors Lnd a fuselage model. The wind tunnel installation of the TRAM isolated rotor is shown. The rotor tested in the DNW was a 1/4-scale (9.5 ft diameter) model of the right-hand V-22 proprotor. The rotor and nacelle assembly was attached to an acoustically-treated, isolated rotor test stand through a mechanical pivot (the nacelle conversion axis). The TRAM was analyzed using the rotorcraft comprehensive analysis CAMRAD II. CAMRAD II is an aeromechanical analysis of helicopters and rotorcraft that incorporates a combination of advanced technologies, including multibody dynamics, nonlinear finite elements, and rotorcraft aerodynamics. The trim task finds the equilibrium solution (constant or periodic) for a steady state operating condition, in this case a rotor operating in a wind tunnel. For wind tunnel operation, the thrust and flapping are trimmed to target values. The aerodynamic model includes a wake analysis to calculate the rotor nonuniform induced-velocities, using a free wake geometry. The paper will present the results of CAMRAD II calculations compared to the TRAM DNW measurements for hover performance, helicopter mode performance, and helicopter mode airloads. An example of the hover performance results, comparing both mearements and calculations for the JVX (large scale) and TRAM (small scale) rotors, is shown. An example of the helicopter mode performance, showing the influence of the aerodynamic model (particularly the stall delay model) on the calculated power, induced power, and profile power is also shown. An example of the helicopter mode airloads, showing the influence of various wake and aerodynamic models on the calculations, is shown. Good correlation with measured airloads is obtained using the multiple-trailer wake model. The paper will present additional results, and describe and discuss the aerodynamic behavior in detail.

Johnson, Wayne↗

NASA NTRS2003

Navier-Stokes and Comprehensive Analysis Performance Predictions of the NREL Phase VI Experiment

A vortex lattice code, CAMRAD II, and a Reynolds-Averaged Navier-Stoke code, OVERFLOW-D2, were used to predict the aerodynamic performance of a two-bladed horizontal axis wind turbine. All computations were compared with experimental data that was collected at the NASA Ames Research Center 80- by 120-Foot Wind Tunnel. Computations were performed for both axial as well as yawed operating conditions. Various stall delay models and dynamics stall models were used by the CAMRAD II code. Comparisons between the experimental data and computed aerodynamic loads show that the OVERFLOW-D2 code can accurately predict the power and spanwise loading of a wind turbine rotor.

NREL (NATIONAL RENEWABLE ENERGY LABORATORY)↗

NASA NTRS2002

Advanced Rotor Aerodynamics Concepts with Application to Large Rotorcraft

A study was conducted using the comprehensive analysis CAMRAD II to explore performance enhancements to large rotorcraft. The aircraft considered were a 125 foot diameter six-bladed rotor helicopter and an 85 foot diameter four-bladed rotor tilt rotor. The objectives were to reduce power required and increase maximum lift. The effects of improved airfoils and active controls were investigated. Airfoils with higher maximum lift and with reduced drag were investigated. Results showed a moderate improvement in the maximum lift capability for the helicopter and a large improvement for the tilt rotor. For the helicopter, 2/rev individual blade control resulted in modest power savings in cruise flight, which increased with control amplitude and forward speed. The optimum phase for the individual blade control was relatively insensitive to both amplitude and forward speed. The influences of active twist, increased chord, increments in airfoil properties, and tilt rotor tip extensions were also investigated.

Floros, Matthew W.↗

NASA NTRS2002

Wind Tunnel Measurements and Calculations of Aerodynamic Interactions Between Tiltrotor Aircraft

Wind tunnel measurements and calculations of the aerodynamic interactions between two tiltrotor aircraft in helicopter mode are presented. The measured results include the roll moment and thrust change on the downwind aircraft, as a function of the upwind aircraft position (longitudinal, lateral, and vertical). Magnitudes and locations of the largest interactions are identified. The calculated interactions generally match the measurements, with discrepancies attributed to the unsteadiness of the wake and aerodynamic forces on the airframe. To interpret the interactions in terms of control and power changes on the aircraft, additional calculations are presented for trimmed aircraft with gimballed rotors.

Johnson, Wayne↗

NASA NTRS2001

Airloads and Wake Geometry Calculations for an Isolated Tiltrotor Model in a Wind Tunnel

Comparisons of measured and calculated aerodynamic behavior of a tiltrotor model are presented. The test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, 0.25-scale V-22 rotor in the German-Dutch Wind Tunnel (DNW) provides an extensive set of aeroacoustic, performance, and structural loads data. The calculations were performed using the rotorcraft comprehensive analysis CAMRAD II. Presented are comparisons of measured and calculated performance for hover and helicopter mode operation, and airloads for helicopter mode. Calculated induced power, profile power, and wake geometry provide additional information about the aerodynamic behavior. An aerodynamic and wake model and calculation procedure that reflects the unique geometry and phenomena of tiltrotors has been developed. There are major differences between this model and the corresponding aerodynamic and wake model that has been established for helicopter rotors. In general, good correlation between measured and calculated performance and airloads behavior has been shown. Two aspects of the analysis that clearly need improvement are the stall delay model and the trailed vortex formation model.

Johnson, Wayne↗

NASA NTRS2001

Calculation of the Aerodynamic Behavior of the Tilt Rotor Aeroacoustic Model (TRAM) in the DNW

Comparisons of measured and calculated aerodynamic behavior of a tiltrotor model are presented. The test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, 1/4-scale V- 22 rotor in the German-Dutch Wind Tunnel (DNW) provides an extensive set of aeroacoustic, performance, and structural loads data. The calculations were performed using the rotorcraft comprehensive analysis CAMRAD II. Presented are comparisons of measured and calculated performance and airloads for helicopter mode operation, as well as calculated induced and profile power. An aerodynamic and wake model and calculation procedure that reflects the unique geometry and phenomena of tiltrotors has been developed. There are major differences between this model and the corresponding aerodynamic and wake model that has been established for helicopter rotors. In general, good correlation between measured and calculated performance and airloads behavior has been shown. Two aspects of the analysis that clearly need improvement are the stall delay model and the trailed vortex formation model.

Johnson, Wayne↗

NASA NTRS2001

Influence of Wake Models on Calculated Tiltrotor Aerodynamics

The tiltrotor aircraft configuration has the potential to revolutionize air transportation by providing an economical combination of vertical take-off and landing capability with efficient, high-speed cruise flight. To achieve this potential it is necessary to have validated analytical tools that will support future tiltrotor aircraft development. These analytical tools must calculate tiltrotor aeromechanical behavior, including performance, structural loads, vibration, and aeroelastic stability, with an accuracy established by correlation with measured tiltrotor data. The recent test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single,l/4-scale V-22 rotor in the German-Dutch Wind Tunnel (DNW) provides an extensive set of aeroacoustic, performance, and structural loads data. This paper will examine the influence of wake models on calculated tiltrotor aerodynamics, comparing calculations of performance and airloads with TRAM DNW measurements. The calculations will be performed using the comprehensive analysis CAMRAD II.

Johnson, Wayne↗

NASA NTRS2000

Analysis of Advanced Rotorcraft Configurations

Advanced rotorcraft configurations are being investigated with the objectives of identifying vehicles that are larger, quieter, and faster than current-generation rotorcraft. A large rotorcraft, carrying perhaps 150 passengers, could do much to alleviate airport capacity limitations, and a quiet rotorcraft is essential for community acceptance of the benefits of VTOL operations. A fast, long-range, long-endurance rotorcraft, notably the tilt-rotor configuration, will improve rotorcraft economics through productivity increases. A major part of the investigation of advanced rotorcraft configurations consists of conducting comprehensive analyses of vehicle behavior for the purpose of assessing vehicle potential and feasibility, as well as to establish the analytical models required to support the vehicle development. The analytical work of FY99 included applications to tilt-rotor aircraft. Tilt Rotor Aeroacoustic Model (TRAM) wind tunnel measurements are being compared with calculations performed by using the comprehensive analysis tool (Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics (CAMRAD 11)). The objective is to establish the wing and wake aerodynamic models that are required for tilt-rotor analysis and design. The TRAM test in the German-Dutch Wind Tunnel (DNW) produced extensive measurements. This is the first test to encompass air loads, performance, and structural load measurements on tilt rotors, as well as acoustic and flow visualization data. The correlation of measurements and calculations includes helicopter-mode operation (performance, air loads, and blade structural loads), hover (performance and air loads), and airplane-mode operation (performance).

Johnson, Wayne↗

NASA NTRS2000

Improving Tiltrotor Whirl-Mode Stability with Rotor Design Variations

Further increases in tiltrotor speeds are limited by coupled wing/rotor whirl-mode aeroelastic instability. Increased power, thrust, and rotor efficiency are not enough: the whirl-mode stability boundary must also be improved. With current technology, very stiff, thick wings of limited aspect ratio are essential to meet the stability requirements, which severely limits cruise efficiency and maximum speed. Larger and more efficient tiltrotors will need longer and lighter wings, for which whirl-mode flutter is a serious design issue. Numerous approaches to improving the whirl-mode airspeed boundary have been investigated, including tailored stiffness wings, active stability augmentation, variable geometry rotors, highly swept tips, and at one extreme, folding rotors. The research reported herein began with the much simpler approach of adjusting the chordwise positions of the rotor blade aerodynamic center and center of gravity, effected by offsetting the airfoil quarter chord or structural mass with respect to the elastic axis. The research was recently extended to include variations in blade sweep, control system stiffness, and pitch-flap coupling (delta(sub 3)). As an introduction to the subject, and to establish a baseline against which to measure stability improvements, this report will first summarize results. The paper will then discuss more advanced studies of swept blades and control-system modifications.

Acree, C. W., Jr.↗

NASA NTRS1999

Numerical Predictions of Wind Turbine Power and Aerodynamic Loads for the NREL Phase II and IV Combined Experiment Rotor

Accurate, reliable and robust numerical predictions of wind turbine rotor power remain a challenge to the wind energy industry. The literature reports various methods that compare predictions to experiments. The methods vary from Blade Element Momentum Theory (BEM), Vortex Lattice (VL), to variants of Reynolds-averaged Navier-Stokes (RaNS). The BEM and VL methods consistently show discrepancies in predicting rotor power at higher wind speeds mainly due to inadequacies with inboard stall and stall delay models. The RaNS methodologies show promise in predicting blade stall. However, inaccurate rotor vortex wake convection, boundary layer turbulence modeling and grid resolution has limited their accuracy. In addition, the inherently unsteady stalled flow conditions become computationally expensive for even the best endowed research labs. Although numerical power predictions have been compared to experiment. The availability of good wind turbine data sufficient for code validation experimental data that has been extracted from the IEA Annex XIV download site for the NREL Combined Experiment phase II and phase IV rotor. In addition, the comparisons will show data that has been further reduced into steady wind and zero yaw conditions suitable for comparisons to "steady wind" rotor power predictions. In summary, the paper will present and discuss the capabilities and limitations of the three numerical methods and make available a database of experimental data suitable to help other numerical methods practitioners validate their own work.

Duque, Earl P. N.↗

NASA NTRS1993

Correlation of airloads on a two-bladed helicopter rotor

Airloads measured on a two-bladed helicopter rotor in flight during the Ames' Tip Aerodynamic and Acoustic Test are compared with calculations from a comprehensive helicopter analysis (CAMRAD/JA), and the pressures compared with calculations from a full-potential rotor code (FPR). The flight-test results cover an advance ratio range of 0.19 to 0.38. The lowest-speed case is characterized by the presence of significant blade-vortex interactions. Good correlation of peak-to-peak vortex-induced loads and the corresponding pressures is obtained. Results of the correlation for this two-bladed rotor are substantially similar to those for three- and four-bladed rotors, including the tip-vortex core size for best correlation, calculation of the peak-to-peak loads on the retreating side, and calculation of vortex iduced loads on inboard radial stations. The higher-speed cases are characterized by the presence of transonic flow on the outboard sections of the blade. Comparison of calculated and measured airloads on the advancing side is not considered appropriate because the presence of shocks makes chordwise integration of the measured data difficult. However, good correlation of the corresponding pressures is obtained.

Fernandez, Francisco J.↗

NASA NTRS1993

Performance results from a test of an S-76 rotor in the NASA Ames 80- by 120-foot wind tunnel

A full-scale helicopter rotor wind tunnel test has been conducted which covers a wide range of rotor-shaft angles-of-attack and 0-100 kt thrust conditions. The hover performance data thus obtained were compared with the results of momentum theory calculations; forward flight rotor-performance data were compared with calculations from a comprehensive rotorcraft analysis. These comparisons suggest that hover testing at an outdoor facility in the absence of ground effect is required to make a final determination of the absolute accuracy of the wind tunnel hover data.

Shinoda, Patrick M.↗

NASA NTRS1991

Aeroelastic loads and stability investigation of a full-scale hingeless rotor

An analytical investigation was conducted to study the influence of various parameters on predicting the aeroelastic loads and stability of a full-scale hingeless rotor in hover and forward flight. The CAMRAD/JA (Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics, Johnson Aeronautics) analysis code is used to obtain the analytical predictions. Data are presented for rotor blade bending and torsional moments as well as inplane damping data obtained for rotor operation in hover at a constant rotor rotational speed of 425 rpm and thrust coefficients between 0.0 and 0.12. Experimental data are presented from a test in the wind tunnel. Validation of the rotor system structural model with experimental rotor blade loads data shows excellent correlation with analytical results. Using this analysis, the influence of different aerodynamic inflow models, the number of generalized blade and body degrees of freedom, and the control-system stiffness at predicted stability levels are shown. Forward flight predictions of the BO-105 rotor system for 1-G thrust conditions at advance ratios of 0.0 to 0.35 are presented. The influence of different aerodynamic inflow models, dynamic inflow models and shaft angle variations on predicted stability levels are shown as a function of advance ratio.

Peterson, Randall L.↗

NASA NTRS1991

Computing The Dynamics Of Helicopters

Comprehensive Analytical Model of Rotorcraft Aerodynamics (CAMRAD) computer program designed to calculate performance of, loads on, and noise generated by, helicopter rotor; vibration of helicopter and its response to gusts; dynamics and handling qualities of helicopter in flight; and aeroelastic stability of helicopter as system. Analysis consistent combination of structural, inertial, and aerodynamical mathematical models applicable to wide range of problems and wide class of vehicles. Written in FORTRAN 77.

Johnson, Wayne↗

NASA NTRS1991

Vibration analysis of the SA349/2 helicopter

Helicopter airframe vibration is examined using calculations and measurements for the SA349/2 research helicopter. The hub loads, which transmit excitations to the fuselage, are predicted using a comprehensive rotorcraft analysis and correlated with measuring hub loads. The predicted and measured hub loads are then coupled with finite element models representing the SA349/2 fuselage. The resulting vertical acceleration at the pilot seat is examined. Adjustments are made to the airframe structural models to examine the sensitivity of predicted vertical acceleration to the model. Changes of a few percent to the damping and frequency of specific models lead to large reductions in predicted vibration, and to major improvements in the correlations with measured pilot-seat vertical acceleration.

Heffernan, Ruth↗

NASA NTRS1991

Analysis and correlation of SA349/2 helicopter vibration

Helicopter airframe vibration is examined using calculation and measurements for the SA349/2 research helicopter. The hub loads, which transmit excitation to the fuselage, are predicted using a comprehensive rotorcraft analysis and correlated with measured hub loads. The predicted and measured hub loads are then coupled with finite element models representing the SA349/2 fuselage. The resulting vertical acceleration at the pilot seat is examined. Adjustments are made to the airframe structural models to examine the sensitivity of predicted vertical acceleration to the model. Changes of a few percent to the damping and frequency of specific modes lead to large reductions in predicted vibration and to major improvements in the correlations with measured pilot seat vertical acceleration.

Heffernan, Ruth↗

NASA NTRS1991

Correlation of airloads on a two-bladed helicopter rotor

Airloads measured on a two-bladed helicopter rotor in flight, from the Tip Aerodynamic and Acoustic Test, are compared with calculations from a comprehensive helicopter analysis (CAMRAD/JA), and the pressures compared with calculations from a full-potential rotor code (FPR). The flight test results cover an advance ratio range from 0.19 to 0.38. The lowest speed case is characterized by the presence of significant blade-vortex interactions. Good correlation of peak-to-peak vortex-induced loads and the corresponding pressures is obtained. The results of the correlation for this two-bladed rotor are substantially similar to the results for three- and four-bladed rotors, concerning the tip vortex core size for best correlation, calculation of the peak-to-peak loads on the retreating side, and calculation of vortex-induced loads on inboard radial stations.

Hernandez, Francisco↗