Engineering topics

Johnson, Wayne

Publications and source records attributed to Johnson, Wayne.

101 records · Page 6

NASA NTRS1990

Feasibility investigation of general time-domain unsteady aerodynamics of rotors

The feasibility of a general theory for the time-domain unsteady aerodynamics of helicopter rotors is investigated. The wake theory gives a linearized relation between the downwash and the wing bound circulation, in terms of the impulse response obtained directly in the time domain. This approach makes it possible to treat general wake configurations, including discrete wake vorticity with rolled-up and distorted geometry. The investigation establishes the approach for model order reduction; determines when a constrained identification method is needed; verifies the formulation of the theory for rolled-up, distorted trim wake geometry; and verifies the formulation of the theory for wake geometry perturbations. The basic soundness of the approach is demonstrated by the results presented. A research program to complete the development of the method is outlined. The result of this activity will be an approach for analyzing the aeroelastic stability and response of helicopter rotors, while retaining the important influence of the complicated rotor wake configuration.

Johnson, Wayne↗

NASA NTRS1990

Airloads, wakes, and aeroelasticity

Fundamental considerations regarding the theory of modeling of rotary wing airloads, wakes, and aeroelasticity are presented. The topics covered are: airloads and wakes, including lifting-line theory, wake models and nonuniform inflow, free wake geometry, and blade-vortex interaction; aerodynamic and wake models for aeroelasticity, including two-dimensional unsteady aerodynamics and dynamic inflow; and airloads and structural dynamics, including comprehensive airload prediction programs. Results of calculations and correlations are presented.

Johnson, Wayne↗

NASA NTRS1990

Hub loads analysis of the SA349/2 helicopter

The forces and moments at the rotor hub of an Aerospatiale SA349/2 helicopter were investigated. The study included three main topics. First, measured hub forces and moments for a range of level flight conditions (mu = 0.14 to 0.37) were compared with predictions from a comprehensive rotorcraft analysis to examine the influence of the wake model on the correlations. Second, the effect of changing the blade mass distribution and blade chordwise center of gravity location on the 3/rev nonrotating frame hub loads was studied for a high-speed flight condition (mu = 0.37). Third, the use of higher harmonic control to reduce nonrotating frame 3/rev hub shear forces was investigated. The last two topics were theoretical studies only.

Heffernan, Ruth M.↗

NASA NTRS1990

Airloads and wake models for a comprehensive helicopter analysis

Johnson, Wayne↗

NASA NTRS1989

Correlation of Puma airloads: Lifting-line and wake calculation

A cooperative program undertaken by organizations in the United States, England, France, and Australia has assessed the strengths and weaknesses of four lifting-line/wake methods and three CFD methods by comparing their predictions with the data obtained in flight trials of a research Puma. The Puma was tested in two configurations: a mixed bladed rotor with instrumented rectangular tip blades, and a configuration with four identical swept tip blades. The results are examined of the lifting-line predictions. The better lifting-line methods show good agreement with lift at the blade tip for the configuration with four swept tips; the moment is well predicted at 0.92 R, but deteriorates outboard. The predictions for the mixed bladed rotor configuration range from fair to good. The lift prediction is better for the swept tip blade than for the rectangular tip blade, but the reasons for this cannot be determined because of the unmodeled effects of the mixed bladed rotor.

Bousman, William G.↗

NASA NTRS1989

Application of the joined wing to tiltrotor aircraft

A study was made to determine the potential speed improvements and other benefits resulting from the application of the joined wing concept to tiltrotor aircraft. Using the XV-15 as a baseline, the effect of replacing the cantilever wing by a joined-wing pair was studied. The baseline XV-15 cantilever wing has a thickness/chord ratio of 23 percent. It was found that this wing could be replaced by a joined-wing pair of the same span and total area employing airfoils of 12 percent thickness/chord ratio. The joined wing meets the same static strength requirements as the cantilever wing, but increases the limiting Mach Number of the aircraft from M=0.575 to M=0.75, equivalent to an increase of over 100 knots in maximum speed. The joined wing configuration studied is lighter than the cantilever and has approximately 11 percent less wing drag in cruise. Its flutter speed of 245 knots EAS is not high enough to allow the potential Mach number improvement to be attained at low altitude. The flutter speed can be raised either by employing rotors which can be stopped and folded in flight at speeds below 245 knots EAS, or by modifying the airframe to reduce adverse coupling with the rotor dynamics. Several modifications of wing geometry and nacelle mass distribution were investigated, but none produced a flutter speed above 260 knots EAS. It was concluded that additional research is required to achieve a more complete understanding of the mechanism of rotor/wing coupling.

Wolkovitch, Julian↗

NASA NTRS1989

Calculation of blade-vortex interaction airloads on helicopter rotors

Two alternative approaches area developed to calculate blade-vortex interaction airloads on helicopter rotors, second-order lifting-line theory and a lifting-surface theory correction. The common approach of using a larger vortex core radius to account for lifting-surface effects is quantified. The second-order lifting-line theory also improves the modeling of low aspect-ratio blades yawed flow, and swept tips. Calculated results are compared with wind-tunnel measurements of lateral flapping, and with flight test measurements of blade section lift on SA349/2 and H-34 helicopter rotors. The tip vortex core radius required for good correlation with the flight test data is about a 20-percent chord, which is within the range of measured viscous core sizes for helicopter rotors.

Johnson, Wayne↗

NASA NTRS1987

The effect of nonlinear elastomeric lag damper characteristics on helicopter rotor dynamics

Many helicopters use elastomeric lag dampers to prevent ground resonance and aeromechanical instability in hover and forward flight. Recent experimental results have shown that when the damper motion occurs at two superimposed frequencies, which is characteristic of operation in forward flight, the damper properties are not well-predicted by a superposition of the damper properties at each of the motion frequencies. This paper presents experimental data obtained with an elastomeric damper while it was undergoing single- and dual-frequency motion. The effect of the nonlinear dual-frequency damper characteristics on predicted rotor aeromechanical stability in forward-flight operation in a wind tunnel was evaluated using the comprehensive rotorcraft analysis program called CAMRAD.

Felker, Fort F.↗

NASA NTRS1987

Calculated performance, stability, and maneuverability of high speed tilting proprotor aircraft

The feasibility of operating tilting proprotor aircraft at high speeds is examined by calculating the performance, stability, and maneuverability of representative configurations. The rotor performance is examined in high speed cruise and in hover. The whirl flutter stability of the coupled wing and rotor motion is calculated in cruise. Maneuverability is examined in terms of the rotor thrust limit during turns in helicopter configuration. Rotor airfoils, rotor hub configuration, wing airfoil, and airframe structural weights representative of demonstrated advanced technology are considered. Key rotor and airframe parameters are optimized for high speed performance and stability. The basic aircraft design parameters are optimized for minimum gross weight. To provide a focus for the calculations, two high speed tiltrotor aircraft are considered: a 46-passenger civil transport and an air-combat/escort fighter, both with design speeds of about 400 knots. It is concluded that such high speed tiltrotor aircraft are quite practical.

Johnson, Wayne↗

NASA NTRS1986

Calculated performance, stability and maneuverability of high-speed tilting-prop-rotor aircraft

The feasibility of operating tilting-prop-rotor aircraft at high speeds is examined by calculating the performance, stability, and maneuverability of representative configurations. The rotor performance is examined in high-speed cruise and in hover. The whirl-flutter stability of the coupled-wing and rotor motion is calculated in the cruise mode. Maneuverability is examined in terms of the rotor-thrust limit during turns in helicopter configuration. Rotor airfoils, rotor-hub configuration, wing airfoil, and airframe structural weights representing demonstrated advance technology are discussed. Key rotor and airframe parameters are optimized for high-speed performance and stability. The basic aircraft-design parameters are optimized for minimum gross weight. To provide a focus for the calculations, two high-speed tilt-rotor aircraft are considered: a 46-passenger, civil transport and an air-combat/escort fighter, both with design speeds of about 400 knots. It is concluded that such high-speed tilt-rotor aircraft are quite practical.

Johnson, Wayne↗

NASA NTRS1986

Calculated performance, stability, and maneuverability of high-speed tilting-prop-rotor aircraft

The feasability of operating tilting-prop-rotor aircraft at high speeds is examined by calculating the performance, stability, and maneuverability of representative configurations. The rotor performance is examined in high-speed cruise and in hover. The whirl-flutter stability of the coupled-wing and rotor motion is calculated in the cruise mode. Maneuverability is examined in terms of the rotor-thrust limit during turns in helicopter configuration. Rotor airfoils, rotor-hub configuration, wing airfoil, and airframe structural weights representing demonstrated advanced technology are discussed. Key rotor and airframe parameters are optimized for high-speed performance and stability. The basic aircraft-design parameters are optimized for minimum gross weight. To provide a focus for the calculations, two high-speed tilt-rotor aircraft are considered: a 46-passenger, civil transport and an air-combat/escort fighter, both with design speeds of about 400 knots. It is concluded that such high-speed tilt-rotor aircraft are quite practical.

Johnson, Wayne↗