Search NASA⌕ Search

Engineering topics

Jordan-Sweet, J

Publications and source records attributed to Jordan-Sweet, J.

At least 19 records

Strain relaxation in single crystal SrTiO{sub 3} grown on Si (001) by molecular beam epitaxy

An epitaxial layer of SrTiO{sub 3} grown directly on Si may be used as a pseudo-substrate for the integration of perovskite oxides onto silicon. When SrTiO{sub 3} is initially grown on Si (001), it is nominally compressively strained. However, by subsequent annealing in oxygen at elevated temperature, an SiO{sub x} interlayer can be formed which alters the strain state of SrTiO{sub 3}. We report a study of strain relaxation in SrTiO{sub 3} films grown on Si by molecular beam epitaxy as a function of annealing time and oxygen partial pressure. Using a combination of x-ray diffraction, reflection high energy electron diffraction, and transmission electron microscopy, we describe the process of interfacial oxidation and strain relaxation of SrTiO{sub 3} on Si (001). Understanding the process of strain relaxation of SrTiO{sub 3} on silicon will be useful for controlling the SrTiO{sub 3} lattice constant for lattice matching with functional oxide overlayers.

36 MATERIALS SCIENCE↗

A Quantitative Analysis of Room Temperature Recrystallization Kinetics in Electroplated Copper Films using High Resolution X-ray Diffraction

Time-resolved in situ x-ray diffraction measurements were used to study the room-temperature recrystallization kinetics of electroplated copper thin films with thicknesses between 400 and 1000 nm. The thinnest films exhibited limited recrystallization and subsequent growth of grains, while recrystallized grains in the thicker films grew until all as-plated microstructure was consumed. For all films, recrystallized grains that belonged to the majority texture component, <111>, started growing after the shortest incubation time. These grains exhibited volumetric growth until they achieved the film thickness. After this point the growth mode became planar, with the <111>-type grains growing in the plane of the film. Grains with the <111> direction normal to the film surface started growing after the <111>-type grains switched to planar growth. However, the planar growth of this texture component finished at the same time as the growth of the <111> grains. Profile fitting of the 111 peak permitted the separation of the diffraction signals from recrystallized and as-plated grain populations. The average strains in these two populations, calculated from the peak position of the corresponding {l_brace}111{r_brace} reflections, were different, indicating a heterogeneous stress state within this texture component. The increasing volume fraction of recrystallized <111> grains with time was monitored via the variation in the diffracted intensity. This variation could be represented by the Johnson-Mehl-Avrami-Kolmogorov model.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Characterizing the Effects of Etch-induced Material Modification on the Crystallization Properties of Nitron Doped Ge2Sb2Te5

The chemical and structural effects of processing on the crystallization of nitrogen doped Ge{sub 2}Sb{sub 2}Te{sub 5} is examined via x-ray photoelectron spectroscopy (XPS), x-ray absorption spectroscopy (XAS), time resolved laser reflectivity, and time resolved x-ray diffraction (XRD). Time resolved laser reflectivity and XRD show that exposure to various etch and ash chemistries significantly reduces the crystallization speed while the transition temperature from the rocksalt to the hexagonal phase is increased. XPS and XAS attribute this to the selective removal and oxidization of N, Ge, Sb, and Te, thus altering the local bonding environment to the detriment of device performance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Triaxial Stress Distributions in Cu / low-k Interconnect Features

The distribution of triaxial stresses within single damascene Cu/organosilicate interconnect structures as a function of linewidth, ranging from 45 to 250 nm, was measured using x-ray diffraction. Least-squares minimization techniques were employed to determine the volume-averaged stress tensors of the Cu features. Longitudinal Cu stress values increased for linewidths below 100 nm, while transverse stresses decreased with decreasing linewidth below 100 nm due to the interplay between the Cu microstructure and the feature geometry. Large tensile out-of-plane stresses were observed in all of the lines demonstrating the constraint imposed by the barrier layers that encapsulate the Cu.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Materials and Electrical Characterization of Physical Vapor Deposited LaxLu1-xO3 Thin Films on 300 mm Silicon

La{sub x}Lu{sub 1-x}O{sub 3} thin films were deposited on 300 mm silicon wafers by physical vapor deposition and fabricated into field-effect transistors using a gate-first process flow. The films were characterized using transmission electron microscopy, Rutherford backscattering spectrometry, and synchrotron x-ray diffraction. The results show the films remain amorphous even at temperatures of 1000 C. The dielectric properties of La{sub x}Lu{sub 1-x}O{sub 3} (0.125 {<=} x {<=} 0.875) thin films were evaluated as a function of film composition. The amorphous La{sub x}Lu{sub 1-x}O{sub 3} thin films have a dielectric constant (K) of 23 across the composition range. The inversion thickness (T{sub inv}) of the La{sub x}Lu{sub 1-x}O{sub 3} thin films was scaled to <1.0 nm.

36 MATERIALS SCIENCE↗

The Crystallization Behavior of Stochiometric and Off-stochiometric Ga-Sb-Te Materials for Phase-Change Memory

The stoichiometric Ga{sub 4}Sb{sub 6}Te{sub 3} and Ga-Sb materials were systematically studied. The alloy Ga{sub 4}Sb{sub 6}Te{sub 3} shows a fast crystallization speed, very high crystallization temperature, T{sub x}, and high electrical contrast. Although stoichiometric GaSb has similar performance and even faster crystallization speed, the electrical contrast is much lower. The other off-stoichiometric compounds we studied all have higher T{sub x} than Ge{sub 2}Sb{sub 2}Te{sub 5} indicating a good amorphous stability. By raising the Sb/Te ratio with GaSb incorporation, T{sub x} and the recrystallization time of melt-quenched, amorphous samples can be effectively increased. The stoichiometric Ga{sub 4}Sb{sub 6}Te{sub 3} with less likelihood of phase-segregation compared to nonstoichiometric compounds is a promising candidate for phase-change memory.

36 MATERIALS SCIENCE↗

Manipulating Stress in Cu/low-k Dielectric Nanocomposites

The interaction of x-rays with organic dielectric materials, which alters their mechanical properties, affects values of stress generated within encapsulated Cu structures. In particular, the evolution of stress within submicron Cu interconnect structures encapsulated by an organosilicate glass can be investigated in situ using synchrotron-based x-ray diffraction. The overall geometry of the composite, along with the amount of irradiation, dictates the change in stress of the Cu features. A quantitative comparison of these findings to mechanical modeling results reveals two modes of modification within the dielectric film: a densification that changes the effective eigenstrain followed by an increase in elastic modulus.

36 MATERIALS SCIENCE↗