Search NASA⌕ Search

Engineering topics

Jun, Jiheon

Publications and source records attributed to Jun, Jiheon.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Compatibility of Fuel System Elastomers and Plastics with a Fast-Pyrolysis Oil (Bio-oil) at Room Temperature

Herein the compatibility of a fast-pyrolysis bio-oil with 17 elastomer and 21 plastic materials common to fuel storage, dispensing, and delivery systems was assessed by measuring volume and hardness. Diesel was used as the baseline for comparison. The elastomer and plastic specimens were exposed to the test fuels at 23 °C. The exposure times were 4 and 16 weeks for the elastomers and plastics, respectively. The elastomers (except for silicone and styrene butadiene) exhibited pronounced swelling in the bio-oil. This was especially true for the fluorocarbons and acrylonitrile rubbers. For the elastomers, a strong correlation between polarity and volume swell was observed. Compositional and structural analysis on one of the fluorocarbon materials showed that the bio-oil was less effective at extracting phthalate additives than the diesel. However, the crystallinity of a fluorocarbon was altered by the bio-oil. Unlike the elastomers, the plastic materials were less impacted by exposure to the bio-oil. This finding is attributed to their denser and more rigid molecular structures (compared to the elastomers). Notable swelling did occur in the nylons, but this swelling was attributed to water absorption rather than polarity. Comparison with previous studies showed that the observed swelling was lower for both the elastomers and the plastics. Solubility (and hence swell) increases with temperature, and because this study was conducted at 23 °C rather than 50 °C, the reduced temperature is responsible for the lower swell levels.

09 BIOMASS FUELS↗
DOE OSTI2022

Corrosivity Screening of Pyrolysis Bio-Oils by Short-Term Alloy Exposures. Laboratory Analytical Procedure (LAP), Issue Date: May 12, 2022

Bio-oils contain organic acids and oxygenated compounds that can lead to corrosion issues during bio-oil processing and storage. This Laboratory Analytical Procedure (LAP) allows for rapid screening of a bio-oil's corrosivity without the need for complex equipment and long-term exposures. A robust and repeatable method for assessing the corrosivity of bio-oils is necessary in order to remove materials degradation as an obstacle to research, upgrading, use and storage of bio-oils. This LAP involves the incubation of a representative alloy, 410 stainless steel (410 SS), specimen in bio-oil over a period of 48 hours at 50 degrees C in a sealed container. The corrosive species in the bio-oil react with and deplete alloy elements such as iron (Fe) and/or chromium (Cr) from the specimen into the bio-oil solution. The depletion of Fe and Cr from the specimen results in a significant mass loss that can be recorded. The mass loss is directly correlated to the corrosivity of a bio-oil. Examples of bio-oils in scope include the ones produced by fast pyrolysis and catalytic fast pyrolysis, as well as liquids produced from hydrothermal liquefaction.

09 BIOMASS FUELS↗
DOE OSTI2022

Standard Analytical Methods for Pyrolysis Bio-Oils

There has been significant recent interest in the production of renewable fuels and chemicals from biomass and waste feedstocks. Pyrolysis pathways produce a liquid bio-oil product, which must be processed further, or upgraded, to yield fuel or chemical products. Bio-oils are very complex and often unstable samples, and research and development on upgrading processes needs reliable analytical information. In particular, chemical characterization techniques are needed to quantify both functional groups and individual compounds present in bio-oils. Reliable analytics are also needed to enable the bioenergy industry, as industrial facilities often have different analytical needs and capabilities than research facilities. In this presentation, we will discuss the development of a suite of standard analytical methods for pyrolysis bio-oils. Analytical methods to be discussed include: Determination of Carbon, Hydrogen, Nitrogen, and Oxygen in bio-oils; Accelerated Aging of Fast Pyrolysis Bio-oil using Carbonyl Titration; Determination of Water Content in Bio-oils by Volumetric Karl Fischer Titration; Determination of Carbon Functional Groups; Elemental Analysis of Bio-oils by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES) - Na, K, Mg, Ca, S, P, and Fe; Determination of Phenolic Groups in Bio-oils using Revised Folin-Ciocalteu Methods: Single Cuvette and Plate Reader; Corrosivity of Bio-oils: Screening Test using Metal Leaching; Determination of Biogenic Content by 14C Measurement using Liquid Scintillation Counter. These new analytical methods are publicly available as Laboratory Analytical Procedures (https://www.nrel.gov/bioenergy/bio-oil-analysis.html), along with previously developed standard methods: GC-MS, Acid Titration, Carbonyl Titration, and 31P NMR. Additionally, the development of diffusion ordered NMR for characterization of bio-oil molecular weight will be discussed. Collectively, this suite of analytical methods represents the most comprehensive set of standard methods available for pyrolysis bio-oils. These standard methods are commonly used by the bioenergy community, and provide reliable information that enables research, scaleup, and industrial processing of biomass to produce renewable fuels and chemicals.

analytical↗
DOE OSTI2022

Electrochemical Corrosion Analysis of Stainless Steels in LALM Pyrolysis Bio-Oil with Organic Corrodents

Pyrolysis bio-oils are corrosive to low alloy steels, e.g., 2.25Cr-1Mo, 5Cr-1Mo, and 9Cr-1Mo grades. To identify the alloys with sufficient bio-oil compatibility, several commercial stainless steels were examined in bio-oil using electrochemical impedance spectroscopy to semi quantitatively assess their corrosion resistance. Low-Ash Low-Moisture (LALM) bio-oil, produced from a forest residue feedstock by the National Renewable Energy Laboratory in Golden, CO, was used as a test liquid for electrochemical impedance spectroscopy measurements. Three organic corrodents, formic acid, catechol, and lactobionic acid, were added into LALM bio-oil to produce test liquids with intentionally increased corrosivity. Corrosion reaction resistance, determined from the impedance data, was used to evaluate the corrosion compatibility of each stainless steel in LALM bio-oil and LALM bio-oil + organic corrodent(s). The results from corrosion reaction resistance indicated that the critical Cr content of stainless steels for corrosion resistance would be greater than 14 wt % if Ni and Mo contents are low but can be as low as 12–13 wt % with appreciable amounts of Ni and Mo.

Jun, Jiheon↗
DOE OSTI2021

Corrosion Prevention of Additively Manufactured Aluminum Packing Devices Developed for Process Intensification of CO 2 Capture by Aqueous Amines

Corrosion of additively manufactured (i.e., 3D printed) aluminum packing devices, developed to enhance heat and mass transfer in CO 2 absorption columns using amine-CO 2 scrubbing solutions, is investigated in this paper. The aluminum structures printed by selective laser melting with Al-10Si-0.3Mg feed powder are susceptible to corrosion in aqueous monoethanolamine, both fresh and used CO 2 -saturated solutions. The efficacy of corrosion-protective surface layers of aqueous polyether–ketone–ketone (PEKK) dip coating to provide amine corrosion resistance to the 3D printed aluminum structure is also evaluated. PEKK nanothick layers were coated on the corrugated surface of a 3D printed structure, identical to that of the intensified device, yielding 27 times higher corrosion resistance than the uncoated Al alloy surface. Finally, a systematic long-term electrochemical corrosion analysis revealed that a multilayer PEKK dip coating protocol enables protection of the 3D printed Al alloy surface in various CO 2 –monoethanolamine solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Compatibility of Alumina-Forming Austenitic Steels in Static and Flowing Pb

Alumina-forming austenitic (AFA) steels were evaluated for the lead fast reactor application in static and flowing high-purity Pb. Two AFA composition ranges with different Ni, Mn, Al, Cr and Nb contents were targeted, and Zr foil was used in an attempt to getter O in some capsules. Based on two rounds of capsule testing at 500–800°C, two AFA compositions were selected for evaluation in flowing Pb with a peak temperature of 650°C in a thermal convection loop made of pre-oxidized FeCrAlMo tubing. After exposure for 1000 h, the mass losses for both AFA alloys were generally low, suggesting good compatibility under these conditions without preoxidation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pre-Oxidation to Improve Liquid Metal Compatibility

Liquid metals represent an aggressive environment where selective degradation can attack structural alloys. Pre-oxidizing structural alloys, particularly those able to form alumina scales, have shown promise for Sn, Pb and Pb–Li concepts for fusion and fission applications. For Pb at 700 °C, a dramatic reduction in mass loss was observed for an alumina-forming austenitic (AFA) steel after pre-oxidation. Likewise, a ferritic FeCrAlMo alloy showed better compatibility in static Sn at 400–500 °C and flowing PbLi when pre-oxidized at 1000 °C to form α-Al2O3. Recent experiments with flowing PbLi at 675–700 °C has shown significant degradation suggesting that alumina-forming alloys are limited to ~ 650 °C in this environment. While the concept is promising, most experiments have been relatively short-term and long-term degradation mechanisms need to be evaluated.

Pint, Bruce↗
DOE OSTI2021

Laser-Interference Surface Preparation for Enhanced Coating Adhesion and Adhesive Joining of Multi-Materials (Final Project Report)

This report investigates a laser-interference surface treatment as a non-contact, i.e., without major solid/liquid medium application or abrasion, and non-chemical surface preparation method for aerospace coating systems. It was proposed to use the laser-interference technique to structure surfaces of Al and/or Ti, creating "rough" surfaces with pre-engineered series of ridges and valleys at submicron scale. The science goal of this study was to develop an understanding of the surface microstructure, topology, and physical mechanisms that would improve adhesion and corrosion protection of Al2024-T3. Microstructure analysis indicates that the laser-interference structuring (LIS) was found to reduce the formation of CuMn-rich precipitates in Al 2024-T3 over a 500-800 nm depth from top surface. The X-cut and cross-hatch coating adhesion ratings indicate that the LIS specimens meet the performance requirements in the coating adhesion specifications by having a higher or identical ranking to those specimens prepared with current state-of-the-art chemical conversion or sulfuric acid anodizing. After the ASTM B117 corrosion exposure, it was found that the laser processed specimens exhibited only few blisters. It was found that the corrosion damage was minimized at a laser rastering speed of 4 mm/s, for which only 33% of specimens developed very minor corrosion damage. The ASTM D1654 creepage ratings, used to evaluate corrosion damage along the scribe lines, were found to be at least nine for all coated panels. These results indicate that the laser-interference technique with the additional acetone wiping has the potential to be further developed as a minor chemical surface preparation technique for chromate-containing epoxy primers coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Compatibility of FeCrAlMo in Flowing Pb-Li at 600°C to 700°C

A series of monometallic thermal convection loops (TCLs) has been conducted to determine the maximum temperature where FeCrAl alloys have compatibility with eutectic lead lithium (Pb-Li) for a dual-coolant fusion blanket. Pre-oxidizing commercial alloy APMT (Fe-21Cr-5Al-3Mo) for 2 h at 1000°C to form a surface α-Al 2 O 3 layer was very effective in reducing the mass loss of specimens in the hot and cold legs of the most recent TCL that was operated for 1000 h with a peak temperature of 700°C. However, unlike previous experiments, the postexposure room temperature ductility of many of the APMT specimens was degraded to <10% total elongation, and many of the specimens at the highest temperature (>680°C) were severely damaged or were not recovered. Furthermore, wide-angle X-ray scattering found that the pre-formed α-Al 2 O 3 scale transformed to a mixture of trigonal and tetragonal LiAlO 2 . The overall results suggest that the maximum temperature for FeCrAl is limited to <700°C.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Corrosion of Ferrous Structural Alloys in Biomass Derived Fuels and Organic Acids

This work investigated the corrosivity of biomass-derived liquid fuels and organic acids associated with bio-oils and conducted a corrosion compatibility evaluation of several structural ferrous alloys in the fuels and acids. Here, the acidity parameters and solution conductivity values were higher in raw pyrolysis bio-oils than postprocessed oils with significant corrosion attack for carbon steel and Fe-2.25Cr-1Mo. However, higher-grade stainless steels, ferritic Fe-15Cr (15Cb) and austenitic types 304L and 316L, showed negligible corrosion loss, whereas lower-Cr ferritic grades 409, 410, and 416 were attacked. Metal leaching tests and electrochemical impedance spectroscopy measurements revealed superior corrosion resistance of 316 over 410 stainless steels in solutions of formic and oxalic acids that can be present in bio-oils. The corrosion evaluation methods utilized in this work provide effective screening tools to identify the compatible structural alloys for bio-oils.

09 BIOMASS FUELS↗
DOE OSTI2021

Conceptual design of HFIR irradiation experiment for material compatibility study on liquid Sn divertor

Liquid Sn is one of the promising coolants for liquid surface divertor concept of fusion reactors. However, the compatibility between liquid Sn and structural materials is an important issue that has to be addressed, because liquid Sn is extremely corrosive to steels at high temperatures. The corrosion may be mitigated when a protective Al2O 3 layer is formed on the surface of alumina forming steels. However, the effect of neutron irradiation on the integrity of protective layer is not made clear so far. Japan and US joint research project “FRONTIER” started in 2019 to investigate the material compatibility under neutron irradiation. The purpose of the present study is to develop the conceptual design of the irradiation test capsule which enables material compatibility tests for the alumina forming steels - liquid metal systems under neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory, TN, USA. The three dimensional drawing of capsule structure was then developed. The validity of the material selections for the capsule design was investigated by means of corrosion tests of SiC, Si3N4, Ti, and Mo in liquid Sn at 773 K for 262 hr.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Swell Behavior of Elastomers with a Hydrothermal Liquefaction Bio-Crude and a Fast Pyrolysis Bio-Oil

The compatibility of seventeen elastomer materials with two heavy biofuels (fast pyrolysis bio-oil and hydrothermal liquefaction (HTL) bio-crude) and diesel was assessed through volume change measurements. The elastomers included two fluorocarbons, six acrylonitrile rubbers (NBRs), and one each of fluorosilicone, neoprene, polyurethane, silicone, epichlorohydrin rubber (ECO), a blend of polyvinyl chloride and NBR (OZO), styrene butadiene rubber (SBR), hydrogenated NBR (HNBR) and ethylene propylene diene monomer (EPDM). The specimens were immersed in each test fuel for four weeks at 50°C and then measured for volume change. Afterwards, the specimens were dried, and the volume was remeasured. Ingeneral, the bio-oil produced unacceptable swelling in the fluoroelastomers, ECO, OZO, neoprene, polyurethane, SBR, HNBR, EPDM, silicone and five of the NBRs. In most cases, the HTL bio-crude produced lower (though still unacceptable) swelling than the bio-oil. Materials that showed good compatibility with the HTL biocrude were the fluoroelastomers, OZO, and silicone.

Kass, Michael↗
DOE OSTI2021

Corrosion Behavior of Alloy Structural Steels in Catechol and Biomass-Derived Pyrolysis Oils

Electrochemical impedance spectroscopy (EIS) was used to assess the corrosion behavior of three steels, 2.25Cr-1Mo, 5Cr-1Mo and 9Cr-1Mo (UNS K21590, S50200 and K90941) in bio-oils and catechol, an organic constituent commonly found in bio-oils. Two types of biomass pyrolysis oils produced from selected forest residue feedstocks, classified as high-ash and high-moisture (HAHM) and low-ash and low-moisture (LALM) types and 10 wt.% catechol, were used to test the alloys. According to previous results, 10 wt.% catechol in a water and methanol mixture was corrosive to 2.25Cr-1Mo but not to 9Cr-1Mo, highlighting that increasing Cr content in the steels resulted in improved corrosion resistance. 5Cr-1Mo, a steel with an intermediate Cr content, was tested in catechol solutions to better estimate the critical value of Cr for corrosion resistance under these conditions. Also, the three alloys were tested in both HAHM and LALM bio-oils to assess corrosion susceptibility. For EIS measurements, a customized electrochemical setup was employed to minimize the ohmic path through the bio-oils. The corrosion susceptibility was evaluated by determining the resistance at the alloy-corrosive medium interface.

Jun, Jiheon↗
DOE OSTI2021

Evaluation of Corrosion Susceptibility of Structural Steels in Biomass Derived Pyrolysis Oil

Biomass derived pyrolysis oil is a promising renewable energy source. Due to the variety of biomass feedstocks, the bio-oils could contain a wide range of organic constituents which would provide unique corrosive environments for structural materials. A preliminary work exposed different classes of steels and stainless steels to selected organic constituents of biomass pyrolysis oils and found that corrosion susceptibility, assessed using electrochemical impedance spectroscopy (EIS), was prominent in the steels with Cr lower than 11 wt.%. Although this result suggests stainless steels will resist corrosion by certain organic constituents, it may not be sufficient to predict the corrosion performance in real bio-oils. Therefore, this study attempted electrochemical measurements on Cr-alloyed steels and stainless steels directly exposed to a biomass derived pyrolysis oil. To overcome the low conductivity of bio-oils, a customized Luggin capillary was designed to minimize the ohmic path in bio-oils. The results of this work will be reported.

Jun, Jiheon↗
DOE OSTI2021

Corrosion and Chemical Characterization of Bio-Oils from Biomass with Varying Ash and Moisture Contents

As part of the Feedstock Conversion Interface Consortium four samples of pine chips (all combinations of low and high moisture and ash content) were collected and processed for fast pyrolysis. The prepared biomass samples were liquefied at the National Renewable Energy Laboratory (NREL) using the fast pyrolysis process. Following some characterization of the bio-oils at NREL, the bio-oils were shipped to Oak Ridge National Laboratory (ORNL) for corrosion testing and further characterization.The content and composition of ash in each bio-oil was determined. Corrosion testing consisted of exposing selected metallic and elastomer samples for 1000 hr at 50°C and for longer times at room temperature as well as electrochemical impedance spectroscopy measurements to assess relative corrosivity of the bio-oils. Chemical characterization was conducted to identify the corrosive component of the bio-oils as well as to define the chemical differences among the oils. It was hypothesized that there could be a catalytic effect from the higher ash content in two of the biomass sources. Results of these characterization and corrosion studies will be reported.

Keiser, Jim↗
DOE OSTI2021

Mitigation of Galvanic Corrosion in Bolted Joint of AZ31B and Carbon Fiber-Reinforced Composite Using Polymer Insulation

The use of polymer insulation to mitigate galvanic corrosion was examined for bolted joints of AZ31B Mg alloy and carbon fiber-reinforced composite. To assess the corrosion behaviors of bolted joints with and without polymer insulation, solution immersion and salt spray exposure (ASTM B117) tests were conducted, and the corrosion depths and volumes were determined for the joint specimens after the tests. The polymer-insulated bolted joints exhibited much lower corrosion depths and volumes, highlighting the effective mitigation of galvanic corrosion. The reductions of joint strength in the post-corrosion joint specimens were relatively small (up to ~10%) in the polymer-insulated group but greater (up to 90%) in the group with no insulation. Cross-sectional characterization of post-corrosion joints with polymer insulation revealed local pits developed on AZ31B under galvanic influence, indicating that limited galvanic attack (that did not decrease the joining integrity significantly) could still occur during a long salt spray exposure (~1264 h) owing to the permeation of an aqueous corrosive medium.

36 MATERIALS SCIENCE↗
DOE OSTI2021

BETO 2021 Peer Review - Analytical Development and Standardization for Biomass-Derived Thermochemical Liquids

This project began in FY14 to address the lack of standard chemical characterization analytical methods for bio-oils. Bio-oils are very complex and present numerous analytical challenges; yet reliable chemical information (quantification of both individual compounds and chemical functional groups) is needed to inform upgrading research and refinery co-processing. In this project, analysis needs are first determined from engaging the bioenergy community. Next, standard methods are developed to meet these needs, and then subsequently validated via inter-laboratory studies. Methods that are successfully validated (< 10% variability) are then shared as Laboratory Analytical Procedures (LAPs), which are free and publicly available. We have been tracking LAP use and have seen sustained usage as evidenced by an average of 500 pages views and 100 downloads per quarter, demonstrating the value of these methods to the bioenergy community. LAP methods that are particularly useful and reliable will be chosen for the next-level of standardization through ASTM. We have recently achieved approval by ASTM for our carbonyl titration method. This method (ASTM E3146) is the first example of an ASTM standard solely focused on the chemical characterization of bio-oils. Work in this project is meeting the analysis needs of the bioenergy community and will ultimately help enable the commoditization of bio-oils.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗