Search NASA⌕ Search

Engineering topics

Jun, Jiheon

Publications and source records attributed to Jun, Jiheon.

42 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Corrosion Behavior of Laser-Interference Structured AA2024 Coated with a Chromate-Containing Epoxy Primer

In this study, the corrosion behavior of laser-interference treated AA2024-T3 specimens, which are coated with a primer, is presented. The surface of as-received AA2024-T3 specimens were laser-interference structured by splitting the primary beam of a Q-switched Nd:YAG pulsed nanosecond laser into two beams and focusing them to the same spot on the specimen surface. After being stored in plastic cases for up to 70 d, without any additional cleaning, the specimens were spray painted with a chromate-containing epoxy primer, CA7233, compliant to MIL-PRF-23377 Type I Class C2 specification. The corrosion behavior of laser-interference specimens was assessed against that of specimens prepared by chromated conversion coating and sulfuric acid anodizing treatments. After the ASTM B117 corrosion exposure, it was found that the laser processed specimens exhibited only few blisters. On one hand, most specimens prepared at a laser fluence of 1.78 J/cm 2 , without any additional chemical cleaning, were found to develop one very small blister after only 96 h of exposure. However, the growth of these blisters was not significant even after 1,000 h of salt spray exposure. On the other hand, only a fraction of the specimens prepared at a laser fluence of 1.24 J/cm 2 and acetone wiped right after the laser structuring were found to develop several tiny blisters after 790 h and longer exposure. Overall, it was found that the corrosion damage was minimized at a laser rastering speed of 4 mm/s, a condition for which only 33% of specimens developed very minor corrosion damage. Furthermore, the ASTM D1654 creepage ratings, which was used to evaluate the corrosion damage along the scribe lines, were found to be at least nine for all coated panels. These results indicate that the laser-interference technique with the additional acetone wiping has the potential to be further developed as a nonchemical surface preparation technique for chromate-containing epoxy primers coating systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Compatibility of SiC with ODS FeCrAl in flowing Pb-Li at 600° - 700°C

To establish the maximum operating temperature for the dual coolant lead lithium (DCLL) blanket concept, thermal convection loop (TCL) experiments were conducted for 1000 h with a peak temperature of 700 °C to determine compatibility with commercial eutectic Pb~17at.%Li. Two TCLs were fabricated from alloy APMT (FeCrAlMo) and the baseline TCL experiment contained only APMT specimens. The second TCL experiment exposed more fusion relevant CVD SiC and ODS Fe-10Cr-6Al specimens in the hot and cold legs. In the second experiment, the mass losses were much larger for the ODS FeCrAl specimens and most of the CVD SiC specimens experienced a mass gain as SiC reacted to form an Fe- and Cr-rich carbide reaction product. Dissolved Fe and Cr reacted with the SiC and removing Fe and Cr from the liquid appeared to increase ODS FeCrAl dissolution. Such a dissimilar material interaction appears consistent with thermodynamic calculations. Significant attack at the top of the hot leg in both experiments suggests that the Pb-Li compatibility of FeCrAl alloys is inadequate at 700 °C in a flowing environment and the maximum PbLi temperature is < 675 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Anodization Compatibility of Eutectic Aluminum–Cerium Alloys

Anodizing is the most common method for producing corrosion resistant layer coatings for aluminum alloys. It is possible to use anodizing with most commercial aluminum alloys to increase material corrosion resistance, but often the brittle, passive oxide layer formed during anodization does not adhere well to the material, reducing effectiveness, and overall compatibility. Therefore, it is important for the compatibility and effect of anodization to be studied for any newly developed alloys. Recently developed eutectic Al–Ce alloys offer advantages like high castability, limited or no heat treatment requirements, and high-temperature strength retention. In this work, Al–Ce alloys are shown to have good compatibility with current processes and may exhibit improved adhesion of passivated layer because intermetallic phases anchor the anodized product to unconverted bulk. The source of these phenomena and their effect on material corrosion and layer adhesion properties of Al–Ce alloys will be discussed and compared with results from common commercial aluminum alloys.

Sims, Zachary↗
DOE OSTI2020

Long-Term Corrosion Studies of Pine Derived Bio-Oil and Blends with Heavy Fuel Oil

Biomass derived liquid fuels offer a means to reduce greenhouse gas emissions compared to those produced by combustion of petroleum derived liquid fuels. However, the corrosivity of bio-oils toward the less expensive structural materials creates a material selection problem for designers of storage tanks and combustion systems. Samples of candidate structural materials are being exposed for thousands of hours in multiple fast pyrolysis bio-oils and conditions to evaluate the corrosion resistance of these materials. One method to mitigate the corrosivity of bio-oils and speed their adoption, while also decreasing the pollution issues associated with low quality petroleum derived fuels, is to utilize blends of bio-oil and heavy fuel oil in engines currently solely burning a petroleum-based fuel. In addition to the corrosion studies conducted in 100% bio-oil, studies were also conducted with blends of the fast pyrolysis bio-oil produced from pine tree components with a heavy fuel oil that is used in ocean-going ships. This bio-oil had a very high carboxylic acid content which made it very corrosive to carbon and 2¼ Cr-1 Mo steel and even 409 stainless steel. The heavy fuel oil was not corrosive to carbon steel, but its sulfur content makes it a significant pollution producer and particularly undesirable for use near coastlines. Corrosion tests were conducted with the individual components and with various blends of the two liquid fuels. Studies showed a significantly lower corrosivity of the blends than would be projected assuming linear mixing behavior. Adoption of such blends holds the potential to reduce production of sulfur-containing exhaust gases as well as carbon dioxide from non-renewable fuels.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2020

Long-Term Corrosion Studies Of Pine Derived Bio-Oil And Blends With Heavy Fuel Oil

Biomass derived liquid fuels offer a means to reduce greenhouse gas emissions compared to those produced by combustion of petroleum derived liquid fuels. However, the corrosivity of bio-oils toward the less expensive structural materials creates a material selection problem for designers of storage tanks and combustion systems. Samples of candidate structural materials are being exposed for thousands of hours in multiple fast pyrolysis bio-oils and conditions to evaluate the corrosion resistance of these materials. One method to mitigate the corrosivity of bio-oils and speed their adoption, while also decreasing the pollution issues associated with low quality petroleum derived fuels, is to utilize blends of bio-oil and heavy fuel oil in engines currently solely burning a petroleum-based fuel. In addition to the corrosion studies conducted in 100% bio-oil, studies were also conducted with blends of the fast pyrolysis bio-oil produced from pine tree components with a heavy fuel oil that is used in ocean-going ships. This bio-oil had a very high carboxylic acid content which made it very corrosive to carbon and 2¼ Cr-1 Mo steel and even 409 stainless steel. The heavy fuel oil was not corrosive to carbon steel, but its sulfur content makes it a significant pollution producer and particularly undesirable for use near coastlines. Corrosion tests were conducted with the individual components and with various blends of the two liquid fuels. Studies showed a significantly lower corrosivity of the blends than would be projected assuming linear mixing behavior. Adoption of such blends holds the potential to reduce production of sulfur-containing exhaust gases as well as carbon dioxide from non-renewable fuels.

Keiser, Jim↗
DOE OSTI2020

Mechanical and Corrosion Assessment of Friction Self-Piercing Rivet Joint of Carbon Fiber-Reinforced Polymer and Magnesium Alloy AZ31B

In the present work, thermoset carbon fiber–reinforced polymer (CFRP) was spot joined to magnesium alloy AZ31B by a friction self-piercing riveting (F-SPR) process. Lap shear tensile and cross-tension testing were used to evaluate the mechanical joint performance. An average lap shear tensile load of 5.18 kN was achieved, while an average of 2.81 kN was found from cross-tension testing. All F-SPR samples showed a pullout of AZ31B after mechanical testing, indicating good mechanical interlocking between the steel rivet and AZ31B. Corrosion potential was measured for each material to establish the galvanic corrosion characteristics. As expected, AZ31B was found to be the most active, while thermoset CFRP was the most noble. The steel rivet fell between the AZ31B (active) and the thermoset CFRP (noble). Salt fog corrosion testing (ASTM B-117) was performed to evaluate the corrosion performance of the uncoated F-SPR joint. With up to 200 h of exposure, the post-corroded F-SPR joint integrity retained 81.2% of the pre-exposure F-SPR joint strength with AZ31B pullout failure mode. From cross-sectional analysis of the F-SPR joint, extensive corrosion of AZ31B was observed at the joint and other exposure areas. However, steel rivet was not significantly corroded due to sacrificial anode effect by which AZ31B corroded first in the galvanic couple.

36 MATERIALS SCIENCE↗