Search NASA⌕ Search

Engineering topics

Kardoulaki, Erofili

Publications and source records attributed to Kardoulaki, Erofili.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Measuring thermal diffusivity and gap conductance in uranium nitride and Zircaloy relevant for microreactor applications

Heat transfer across nuclear fuels and structural interfaces is an important factor for evaluating the performance of nuclear power systems. Specifically, heat generated as nuclear fuel fissions must be transported through the cladding material and through the reactor to reach the steam turbine for power generation. As new microreactor designs emerge, maximizing the efficiency of this heat transfer process becomes crucial to make them commercially viable. This article examines thermal diffusivity and gap conductance in uranium nitride (UN) fuel and Zircaloy-4 (Zry4) cladding using light flash analysis (LFA). Thermal diffusivity measurements were made on monolithic UN pellets and Zry4 exposed to carbon at peak operating temperatures of microreactors and show that carbon ingress has a minimal effect on thermal diffusivity when compared with identical materials not exposed to carbon. Evaluation of gap conductance at the UN-Zry4 interface was done using one-dimensional two-layer thermal transport models as a function of applied pressure. Here the results show that increasing pressure on the UN-Zry4 interface leads to gains in gap conductance per unit area in fuel-cladding assemblies at microreactor operating temperatures. While many other variables are expected to influence UN-Zry4 interfacial gap conductance (e.g. contact surface roughness, porosity, localized heating, environmental gas pressure), the work offers a demonstration of using a conventional LFA apparatus to determine this parameter at elevated temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

The Use of High-Density UN Fuel in Heat-Pipe Microreactors

Heat-pipe microreactors (HPMRs) are very small-scale nuclear reactors that employ heat pipes (HPs) for heat removal. HPMRs can be easily integrated with other forms of renewable energies, can be used for emergency responses to disaster relief zones, can be deployed in remote locations not connected to the grid, and can be removed from sites and replaced by new ones. HPMRs can also be used for space missions as HPs do not rely on gravity for heat transfer. Conventional fuel materials, such as uranium oxide (UO 2 ) and uranium oxycarbide (UCO), are currently considered in most existing HPMR designs, but ceramic uranium nitride (UN) fuel that has high uranium density, high thermal conductivity, and high melting point may become a better fuel candidate. Through neutronics calculations, this paper assesses the impact of using UN fuel in HPMRs with two different neutron spectra (fast and thermal) and two different fuel forms [traditional solid fuel pellets and TRi-structural-ISOtropic (TRISO) fuel compacts]. It was concluded that retrofitting HPMRs with UN fuel has the potential to reduce the initial 235 U enrichment requirement by ~3 wt% (to keep the same cycle length) or increase the cycle length (by keeping the same initial 235 U enrichment), which enables more compact and transportable HPMR core designs. However, using UN fuel decreases the control element worth [by up to 20% for the Special Purpose Reactor (SPR) and 5% for HP-MR] and is up to 80% more costly. Increasing 15 N enrichment can further decrease the initial 235 U enrichment requirement and increase the control element worth but is more costly. In conclusion, compared to fast-spectrum HPMRs fueled with solid pellet fuels, retrofitting UN fuel is more suitable for thermal-spectrum HPMRs fueled with TRISO fuel compacts, where the neutron spectrum hardening caused by using UN is less significant.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

The Use of the High-density UN Fuel in Heat-pipe Microreactors

Heat-pipe microreactors (HPMRs) are very small-scale nuclear reactors that employ heat pipes for heat removal. HPMRs can be easily integrated with other forms of renewable energies, used for emergency responses to disaster relief zones, deployed in remote locations not connected to the grid, and removed from sites and replaced by new ones. HPMRs can also be used for space missions as heat pipes do not rely on gravity for heat transfer. Conventional fuel materials, such as UO 2 and UCO, are currently considered in most existing HPMR designs, but ceramic UN fuel that has high uranium density, high thermal conductivity, and a high melting point may become a better fuel candidate.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Carburization behavior of FeCrAl alloy APMT and the critical role of pre-oxidation

The carburization behavior of bare and pre-oxidized APMT has been assessed after long-term graphite exposure at 1000 °C. Bare coupons formed a thick scale after graphite exposure due to carbon interaction and chromium-rich carbides were detected, as predicted from thermodynamic calculations. Additionally, pre-oxidation of APMT was conducted in air, and oxidation kinetics were measured through thermogravimetry. The oxide layer formed at 800 °C failed to prevent carburization. However, increasing the pre-oxidation temperature to 1200 °C produced an oxide layer with good resistance to carbon diffusion indicating that the alpha-alumina formed at high temperatures is key in preventing carburization of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Feasibility Studies and Downselection of New Materials and Manufacturing Technologies for Nuclear Applications

This report is intended to present the results of multi-laboratory collaborative studies on the feasibility and downselection of the structural materials that are newly considered for application to future nuclear energy technologies. The Advanced Materials and Manufacturing Techniques (AMMT) program has been implemented to develop cross-cutting technologies in support of a broad range of nuclear reactor technologies and to maintain U.S. leadership in materials and manufacturing technologies for nuclear energy applications. In line with these program objectives, this collaborative studies aim to explore new materials utilizing advanced manufacturing technologies. The FY23 research scope consists of the feasibility studies on new materials and relevant advanced manufacturing technologies, collection of materials properties data and knowledge through experiments and literature survey, and development and application of decision criteria matrix for downselecting candidate materials and manufacturing technologies. The three-laboratory efforts for FY23 have focused on the three new material groups including oxide dispersion strengthened (ODS) materials, refractory composites and alloys, and high entropy alloys (HEAs) investigated, respectively, by Oak Ridge National Laboratory (ORNL) (work package: CT-23OR130406), Los Alamos National Laboratory (LANL) (CT-23LA130403) and Pacific Northwest National Laboratory (PNNL) (CT-23PN130408). The execution of this multi-lab research aimed to provide the AMMT program a merit-based feasibility study identifying an accelerated development path for these materials. A collaborative approach for achieving this goal was to develop a common materials evaluation criteria matrix and apply to all new candidate materials for the evaluation and prioritization of new materials using advanced manufacturing processes. The decision criteria matrix created is a matrix of criteria which a prospective material is scored against. The evaluation criteria are divided into four categories: Application Space, Environmental Compatibility, Physical & Mechanical Properties, and Manufacturability. Materials are given a score from 1−5 for each criterion, with the highest score (5) essentially mean that a material has the most near-term potential for application. Application of the decision criteria matrix will provide guidance to the future research on new materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Carburization Kinetics of Zircalloy-4 and Its Implication for Small Modular Reactor Performance

Carburization of cladding materials has long been a concern for the nuclear industry and has led to the restricted use of high-thermal conductivity fuels such as uranium carbides. With the rise of small modular reactors (SMRs) that frequently implement a graphite core-block, carburization of reactor components is once more in the foreground as a potential failure mechanism. To ensure commercial viability for SMRs, neutron-friendly cladding materials such as Zr-based alloys are required. In this work, the carburization kinetics of Zircaloy-4 (Zry-4), for the temperature range 1073–1673 K (covering typical operating temperatures and off-normal scenarios) are established. The following Arrhenius relationship for the parabolic constant describing ZrC growth is derived: Kp (in μm2/s) = 609.35 exp(−1.505 × 105/RT)). Overall, the ZrC growth is sluggish below 1473 K which is within the operational temperature range of SMRs. In all cases the ZrC that forms from solid state reaction is hypo-stoichiometric, as confirmed through XRD. The hardness and elastic modulus of carburized Zry-4 are also examined and it is shown that despite the formation of a ZrC layer, C ingress in the Zry-4 bulk does not impact the mechanical response after carburization at 1073 K and 1473 K for 96 h.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The influence of the processing parameters on the reactive flash sintering of ZrO 2 -CeO 2

Reactive flash sintering (RFS) is a method that was recently developed to produce dense single-phase bulk ceramic parts through solid-state reactions in a single-step that only takes a few minutes. The influence of the RFS parameters on the phase purity of a simple mixed oxide, (Zr 0.8 ,Ce 0.2 )O 2 , was investigated. Parameters such as furnace temperature, furnace atmosphere, electric current density, and alternating current (AC) or direct current (DC) were examined. It was found that (Zr 0.8 ,Ce 0.2 )O 2 pellets with high densities, above 90% of its theoretical density, can be produced by RFS in a few minutes when RFS occurs under oxidizing atmospheres, AC fields with current densities of 100 mA·mm –2 , and at a furnace temperature of 1200°C. Reducing conditions such as Ar-H 2 atmosphere and DC fields, low furnace temperatures, and low current densities resulted in phase impurities and poor reactions between the ZrO 2 and the CeO 2 powders. These results show that RFS is a useful method to produce mixed oxides, but it is very sensitive to the processing parameters. This is the first time that the influence of most of the RFS processing parameters has been studied systematically. Thus, the present work aims to provide guidelines on selecting the right processing parameters when exploring RFS.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Uranium nitride (UN) pellets with controllable microstructure and phase – fabrication by spark plasma sintering and their thermal-mechanical and oxidation properties

Dense uranium mononitride (UN) pellets with controlled microstructures and tailored grain size from large-grained to a few microns are synthesized by spark plasma sintering (SPS) combined with high energy ball milling. The impacts of the sintering conditions on fuel microstructure, grain size, physical density, and phase behavior are systematically investigated, and the thermal-mechanical properties and oxidation behavior of the SPS densified UN pellets are characterized. Higher sintering temperatures and longer ball milling durations and thus finer starting UN powders promote sintering and densification, and dense UN pellets above 95% theoretical density can be achieved by SPS at 1873 K for 10 min. UN phase purity is maintained in the SPS-densified pellets sintered at a lower temperature and short duration. A phase heterogeneity with secondary UO 2 or uranium sesquinitride (U 2 N 3 ) occurs for the UN pellets sintered at higher temperatures using finer UN powders. The hardness and fracture toughness of the SPS-densified UN pellets increase with smaller grain sizes and higher densities to 7.9 GPa and 3.5 MPa m 1/2 , respectively. Furthermore, both small (1–2 μm) and large grain-sized (30–50 µm) UN pellets exhibit good thermal conductivity. Dynamic oxidation testing by a thermogravimetric analyzer in air shows that the onset temperature for oxidation varies with microstructure and phase heterogeneity of the SPS densified UN pellets. Particularly, the smaller-grained (micron-sized) UN pellets containing uranium oxides and U 2 N 3 display lower weight gain and significantly-reduced oxidation kinetics, and full oxidation completes at a temperature above 1173 K when tested with a ramp rate of 10 K/min.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Onset of selective laser flash sintering of AlN

Abstract Flash sintering uses a combination of heating and electric fields to rapidly densify ceramics. Previously, it has been shown that a scanning laser can be used to initiate flash sintering in localized regions on an yttria‐stabilized zirconia (YSZ) sample in a process known as selective laser flash sintering (SLFS). In this work, we show using a combination of measurements of electric current flowing through the sample and observations of necks formed between powder particles that aluminum nitride (AlN) can also undergo SLFS. Scan conditions required to initiate SLFS are characterized over a range of laser powers and laser scan speeds in a dry nitrogen environment. It is shown that initiation of SLFS in AlN is governed by both the local input energy density per scan and heat dissipation and a numerical model is developed to predict temperatures during SLFS. Assuming the minimum temperature along the conductive path determines the onset of SLFS, the minimum temperature and time required is 450–670 K in 2–0.25 s for the pressed AlN pellets used in this study for laser scan speeds of 33–300 m/s, laser powers of 10–30 W, and an applied electric field of 3000 V/cm.

Gouws, Andre↗
DOE OSTI2021

High temperature mechanical properties of fluorite crystal structured materials (CeO 2 , ThO 2 , and UO 2 ) and advanced accident tolerant fuels (U 3 Si 2 , UN, and UB 2 )

The mechanical interaction between the fuel and cladding that occurs during operation of a nuclear reactor is important to understand as it can lead to cladding failures and release of radioactive material into the coolant. Additionally, in order to develop better models of the pellet-clad mechanical interactions, the mechanical properties of the fuel at relevant operating temperatures, like the elastic moduli, are needed for current and advanced accident tolerant fuels (ATFs). In this work, elevated temperature nanoindentation and resonant ultrasound spectroscopy were used to measure the moduli and hardness of several fluorite materials (CeO 2 , ThO 2 , UO 2 ) and several ATF candidates (ATF) (U 3 Si 2 , UN, UB 2 ). In addition, a comparison of the two techniques was performed in this study to independently validate the mechanical properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Controlled current-rate AC flash sintering of uranium dioxide

Uranium dioxide (UO2) pellets with controlled microstructures were densified up to 93.4% of their theoretical density in less than 25 minutes at a furnace temperature of 873 K, utilizing controlled current-rate alternating current (AC) flash sintering (FS). Using this AC-FS method it was possible to control the sintering rate and thermal gradients, resulting in dense pellets with no appreciable hourglassing and good mechanical integrity. Moreover, the apparent sintering activation energy for FS and for conventionally sintered samples was estimated to be 108 kJ mol -1 and 380 kJ mol -1 , respectively using the master sintering curve method. The apparent activation energy for FS was remarkably close to those reported in the literature for spark plasma sintering of UO 2 . Furthermore, both these field assisted sintering methods utilize fast heating rates and electrical effects that are likely enhancing the grain boundary diffusion mechanism. Finally controlled current-rate AC-FS has been demonstrated as a technological advancement, capable of producing ceramic nuclear fuels in a fraction of the conventional processing time.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Fabrication and thermophysical properties of UO 2 -UB 2 and UO 2 -UB 4 composites sintered via spark plasma sintering

Uranium dioxide (UO 2 ) composites with uranium diboride (UB 2 ) and uranium tetraboride (UB 4 ) have been proposed as advanced fuel candidates due to their high thermal conductivity, high melting point, high fissile density and their ability to incorporate a built-in burnable poison by tailoring the targeted 10 B/ 11 B ratio. As such, it is important to assess the fabrication, and thermal and micromechanical properties of such composites. In this work, UO 2 -UB 2 and UO 2 -UB 4 samples with boride phase fractions of 5, 15 and 30 wt% were fabricated to high densities (above 95 % theoretical density) via spark plasma sintering (SPS). This enabled sintering at relatively low temperatures and short timescales. SPS also aided in maintaining the target phase fractions of the samples as reactions between the constituent phases were suppressed due to the short timescales and reducing environment during sintering. Here, thermal diffusivity measurements from 299 to 1273 K were conducted through laser flash analysis (LFA). The diffusivity increased as a function of boride weight fraction, and UB 2 additions increased the thermal diffusivity of the composites more than UB 4 additions. Assessment of the LFA results indicated in-situ reactions between the UO 2 and boride phases that suppress the thermal diffusivity occur above 800 K for all samples. Oxidation of the boride phase was proposed as the underlying reaction. This was supported by thermodynamic assessments from the literature, as well as microstructural, crystallographic, and nanoindentation characterization performed on these samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗