Engineering topics

Krasikov, Dmitry

Publications and source records attributed to Krasikov, Dmitry.

6 records

DOE OSTI2024

As‐Doped Polycrystalline CdSeTe: Localized Defects, Carrier Mobility and Lifetimes, and Impact on High‐Efficiency Solar Cells

Abstract The efficiency potential for single‐junction photovoltaics (PV) is described by the detailed balance model, which requires the elimination of nonradiative recombination and perfect minority carrier collection. Improvements in GaAs, Si, and perovskite PV follow this model. It might be more complex for CdTe, a leading thin‐film PV technology. While lifetime, passivation, and doping goals for 25% efficient CdTe solar cells are largely reached, voltage is ≈20% below the detailed balance limit. Why is that? In Se‐alloyed CdSe x Te 1‐x (Se is required for >20% efficiency) additional losses can occur due to electrostatic and bandgap fluctuations and due to electronic trap states. To understand mechanisms limiting CdSeTe solar cell performance and to suggest improvements, carrier dynamics, and transport in CdSe x Te 1‐x with variation in Se composition and as doping is analyzed. It is shown that trapping, likely due to anion‐site defects and their complexes, is correlated with low charge carrier mobility of 0.1–0.6 cm 2 (Vs) −1 . Even with 1000 ns charge carrier lifetimes, carrier diffusion length is less than the absorber thickness, reducing efficiency to ≈23%. Device simulations are used to analyze the performance of CdSe x Te 1‐x solar cells; thermodynamic models are not sufficient for absorbers with electronic disorder and trapping.

14 SOLAR ENERGY↗

DOE OSTI2023

CdTe-based thin film photovoltaics: Recent advances, current challenges and future prospects

Cadmium telluride (CdTe)-based cells have emerged as the leading commercialized thin film photovoltaic technology and has intrinsically better temperature coefficients, energy yield, and degradation rates than Si technologies. More than 30 GW peak (GWp) of CdTe-based modules are installed worldwide, multiple companies are in production, modules are shipping at up to 18.6% efficiency, and lab cell efficiency is above 22%. We review developments in the science and technology that have occurred over approximately the past decade. These achievements were enabled by manufacturing innovations and scaling module production, as well as maximizing photocurrent through window layer optimization and alloyed CdSe x Te 1-x (CST) absorbers. Improved chlorine passivation processes, film microstructure, and serendipitous Se defect passivation significantly increased minority carrier lifetime. Efficiencies >22% have been realized for both Cu and As doped CST-based cells. The path to further efficiency gains hinges primarily on increasing open circuit voltage (V oc ) and fill factor (FF) through innovations in materials, fabrication methods, and device stacks. Replacing the longstanding Cu doping with As doping is resulting in better module stability and is being translated to large-scale production. To realize 25% efficiency and >1 V V oc , research and development is needed to increase the minority carrier lifetime beyond 100 ns, reduce grain boundary and interface recombination, and tailor band diagrams at the front and back interfaces. Many of these goals have been realized separately however combining them together using scalable manufacturing approaches has been elusive to date. We review these achievements and outstanding opportunities for this remarkable photovoltaic technology.

14 SOLAR ENERGY↗

DOE OSTI2021

Diverse simulations of time-resolved photoluminescence in thin-film solar cells: A SnO 2 /CdSe y Te 1-y case study

Time-resolved photoluminescence (TRPL) is widely used to measure carrier lifetime in thin-film solar cell absorbers. However, the injection dependence of data and frequent non-exponential decay shapes complicate the interpretation. Here, we develop a numerical model to simulate injection-dependent TRPL measurements in a SnO 2 /CdSe y Te 1-y case study solar cell structure, considering parameters of interest to researchers in industry and academia. Previous simulations have shown that, in low injection, excess electrons and holes injected by the laser pulse are rapidly separated in the electric field formed by the pn junction. As a result, at early times, the PL signal can decay faster than the Shockley-Read-Hall lifetime in the absorber bulk (t_bulk). Prior simulations have shown that the charge stored in the junction can slowly leak out to affect decays at late times. However, it has not been clear if and to what degree charge storage can affect the slopes extracted from TRPL decays - t_2 - commonly cited as the TRPL-measured lifetime. Here, we show that charge storage can, in some cases, result in t_2 values that substantially overestimate t_bulk. Previous simulations indicate that high injection conditions can screen the junction field and minimize charge separation. Here, we show that continued injection increases can drive down t_2 below t_bulk as radiative recombination becomes dominant. We catalog charge storage and radiative recombination impacts for a diverse set of material parameters and compare results to double-heterostructure models.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS,S↗

DOE OSTI2021

Simulation App for Time-Resolved Photoluminescence in Thin-Film Solar Cells

We develop a COMSOL Multiphysics-based model and application, or "app", for time-resolved photoluminescence (TRPL) measurements in thin-film solar cells. TRPL is commonly used to measure recombination in thin-film solar cells. However, simulations show that decay times extracted from TRPL data are not, in general, equal to the Shockley-Read-Hall lifetime parameter set in the model. Here, we present a model and app, using graded CdSe y Te 1-y solar cells as an example, that can be used to study impacts of a range of potentially important material and measurement parameters on TRPL results.

minority-carrier lifetime↗

DOE OSTI2021

Numerical Simulations of Time-Resolved Photoluminescence in CdSexTe1-x/CdTe Solar Cells

We present initial time-resolved photoluminescence (TRPL) simulations in graded CdSexTe1-e thin-film solar cells to quantify the front-interface recombination velocity, S int,front . Our model includes several composition dependences: bandgap energy, absorption coefficient, electron affinity, and carrier lifetime. Cathodoluminescence spectrum imaging measurements on bevels provide an estimate of the bandgap and the CdSe x Te 1-x alloy composition through the absorber thickness. TRPL decays are simulated as a function of the laser power, S int,front , front-interface band offset, and bulk Shockley-Read-Hall lifetime. We find the impact of S intf,ront on the PL decay increases as the band offset shifts from a "spike" to a "cliff". Recombination rate analysis shows that back-interface recombination could potentially dictate the later part of the TRPL decay "t 2" in high-lifetime CdSe x Te 1-x cells. We briefly discuss ongoing work to determine TRPL measurement conditions that maximize sensitivity to S itnt,front.

CdTe solar cells↗

DOE OSTI2019

Solution for Predictive Physical Modeling in CdTe and Other Thin-Film PV Technologies

The main goal of this work was to eliminate the ambiguity between the observed performance changes under stress and their physical root cause by enabling a depth of modeling that takes account of diffusion and drift at the atomistic level coupled to the electronic subsystem responsible for a PV device’s function. Development of advanced physical models describing capture/emission/ recombination phenomena relevant to multivalent dopants, amphoteric centers, and donor-acceptor pairs was also accomplished. These models, incorporating grain bulk, grain boundaries, and hetero-interface properties, were implemented in a self-contained simulation tool that drastically reduces interpretation ambiguity and, for the first time, allows for predictive design of thin-film PV devices.

14 SOLAR ENERGY↗