Search NASA⌕ Search

Engineering topics

Kruger, Albert A.

Publications and source records attributed to Kruger, Albert A..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Heat Transfer in Nuclear Waste Glasses: Measurements and Modeling of Thermal Radiation Properties

We measured and modeled near infrared extinction of nuclear waste glasses from 300 °C to 1150 °C to enable predictive radiation heat transfer and thermal conductivity estimates. A composition and redox informed model resolved contributions from key chromophores (Fe+2-O-Fe+3, V+4, free and bonded ?Si-OH groups) and, when present, spinel particles that can cause strong scattering. The model reproduced measured absorption from room temperature up to 1150 °C, with minor discrepancies near 1 µm (likely due to possible trace impurities) and 2.5 µm (linked to uncertainty in hydroxy groups). Spectra showed silicate melts were semitransparent mainly in the 0.5–4.0 µm window, responsible for radiation thermal conductivity that generally increases with increasing temperature. We quantified the dependence of effective thermal conductivity on dissolved water and provided distributions across >100 LAW/HLW/DFHLW melts at 1150 °C, supporting improved melter heat transfer modeling.

Ferkl, Pavel↗
DOE OSTI2025

A comparison of ceramic and carbon-based reductants for vitrification of low-activity waste

Sucrose is the current baseline additive at the Hanford Waste Treatment and Immobilization Plant in Washington, USA to control foaming during waste feed to glass transitions and the redox state of the glass melt. Alternative reductants are being investigated to alleviate strain on effluent treatment from toxic acetonitrile production from incomplete combustion of sucrose. This study evaluates ceramic additive options including B4C, B6Si, SiC and VB2 in simulated low-activity waste feed, as well as coke dust, probing the feed volume expansion during melting as well as the gas evolution. All alternative reductant options examined significantly reduced acetonitrile production, however there was variability in their effectiveness as foam-reducing agents. VB2 and coke at the appropriate ratios were similarly effective as sucrose in controlling both foam volume and glass redox state, but with considerably less acetonitrile production. B4C, B6Si and SiC showed more promising foam control and very little acetonitrile production, however all of the final glasses were over reduced, i.e., Fe2+/FeT = 0.5. These alternative reductant studies provide operational flexibility to the operation of the vitrification plant, as well as options for alternative raw materials in industrial glass melting.

Rigby, Jessica C. (ORCID:0000000235719977)↗
DOE OSTI2024

Boron nitride: Novel ceramic reductant for low‐activity waste vitrification

Abstract During vitrification of radioactive wastes, excessive foaming reduces processing rates within melters by hindering heat transfer from the molten glass pool to the reacting melter feed. Formulations of low‐activity waste (LAW) melter feeds, for vitrification at the Waste Treatment and Immobilization Plant at the Hanford Site, conventionally include the addition of sucrose to mitigate excessive foaming by hastening the denitration process. However, incomplete combustion of sucrose produces organics such as acetonitrile (C 2 H 3 N) that may exceed bounding limits of downstream effluent treatment facilities. Using boron nitride (BN) as an alternate reductant to sucrose, in a representative LAW melter feed reduced C 2 H 3 N production by 90% by preventing the low‐temperature sucrose–nitrate reactions. Furthermore, foaming was suppressed due to the higher decomposition temperature of BN than H 3 BO 3 meaning a delayed reaction of a large fraction of boron with the transient glass‐forming melt until above the foam onset temperature, thus reducing the quantity and viscosity of the connected melt and trapping less gas in the foam layer.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Effect of cold-cap-bottom shear stress on primary foam stability

Here, we analyze the heat transfer between the melt pool and the layer of reacting materials called cold cap, which is the determining factor for the glass production rate in Joule-heated air-bubbled nuclear waste glass melters. We consider the effects of bubbling rate, melt viscosity, melt thermal conductivity, conversion kinetics, and shear rate at the cold-cap bottom, and develop simple relationships for the cold-cap bottom temperature and glass production rate. We show that the melt convection enhances the heat transfer to the cold cap by suppressing the thermal boundary layer and primary foam, while the conversion kinetics opposes these effects. Additionally, we mention how dissolving silica particles affects the primary foam stability and discuss the limitations of the presented approach for vigorously foaming feeds.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermo-rheological snapshot of melter feed conversion to glass

Slurry feed charged into an electric melter creates a layer of reacting and melting material (termed cold cap) that floats on the surface of molten glass. The rheological behavior of heated melter feed affects the spreading of slurry at the top of the cold cap and the stability of the primary foam, affecting cold-cap coverage and melter plenum temperatures. The apparent viscosity of a high-alumina high-level waste melter feed was assessed by thermomechanical analysis, high-temperature viscometer, and the hot stage microscopy method, yielding viscosity estimates from ≈10 7.5 Pa s at 550°C to ≈10 2.5 Pa s at 1050°C. As the temperature of feed materials increased, their state changed from rigid solid to dilatant fluid, to pseudoplastic bubbly liquid with dissolving solids, to fully developed foam, and finally to Newtonian glass melt.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Glass-contact refractory of the nuclear waste vitrification melters in the United States: a review of corrosion data and melter life

The performance of the refractory lining in glass melters used for nuclear waste vitrification is critical to the melter reliability for long-term continuous operation. Monofrax® K-3, a high Cr 2 O 3 fused cast refractory material, has been widely used to build the liners of nuclear waste glass melters in the United States. Corrosion behaviour of Monofrax® K-3 refractory has been evaluated based on crucible-scale testing, inspection of the refractory components following scaled melter testing, and inspections of the Defense Waste Processing Facility (DWPF) melter refractory after service. The literature generally consists of empirical models based on short-term testing to describe refractory corrosion dependence on glass composition. Corrosion data from tests with longer testing times, at various temperatures, in the presence of molten salts, and with different redox reactions in the plenum atmosphere exist, may be insufficient to provide accurate refractory service life estimates. Additionally, the corrosion data collected under actual and scaled melter operating conditions are limited. Recommendations to achieve more direct correlation between the laboratory refractory corrosion data predictions and the observed melter service life are discussed to allow for more accurate predictions of the useful life of melter refractory linings.

Jin, Tongan↗
DOE OSTI2024

Temperature and Composition Dependence Modeling of Viscosity and Electrical Conductivity of Low-Activity Waste Glass Melts

The development of models that accurately relate the properties of a glass melt to its temperature and composition is important for glass formulation, melter control, and modeling the melt flow, refractory corrosion, and production rate. Using a database consisting of more than 4,000 data points measured between 900 °C and 1250 °C for over 600 unique low-activity waste glass compositions, we developed models for the melt viscosity and electrical conductivity. Models based on the Gaussian process regression approach outperformed models based on the Vogel–Fulcher–Tammann equation according to four standard metrics and yielded reliable prediction intervals. The models found primarily linear effects between properties and individual components, except for the effect of the Na 2 O mass fraction on the electrical conductivity. The effects were found to be consistent with current theories on physical processes involved with those properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Glass production rate in an electric melter: Melting rate correlation and primary foam stability

Waste loading and melting rate are major factors determining the lifecycle of nuclear waste disposal by vitrification in electric melters in which the heat to the cold cap is delivered from the melt pool. One of the crucial parameters that affect the rate of melting is the temperature at which the primary foam collapses at the cold cap bottom. Further, apart from the transient glass-forming melt viscosity, primary foam stability is affected by the shear stress imposed by the flow in the melt pool and the presence of residual solid particles.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Viscosity of transient glass-forming melt and its relation to foaming during batch-to-glass conversion

Primary foam, which affects the heat transfer into the glass batch and the final glass quality, occurs when a sufficient quantity of transient glass-forming melt evolves with viscosity low enough to close the open porosity of the reacting glass batch. To better understand how the fraction of transient melt and its viscosity affect the primary foam temperature range, we determined, with x-ray diffraction, the fraction and composition of the transient glass-forming melt in a heated waste glass melter feed as a function of temperature. Then we prepared a set of transient melts that occurred within the foaming temperature interval and measured their viscosities with spindle and falling sphere viscometers. Further, the results agree with the Adam-Gibbs and VFT viscosity-composition models, even for transient melt compositions outside of the models compositional validity range. As silica and other refractory particles dissolved in the predominantly borate transient melt while temperature increased, viscosity increased from the initial value of ~500 Pa s at the onset of foaming (~650°C) to a maximum of ~770 Pa s when silica dissolution was almost complete (~700°C). As temperature increased further, transient melt viscosity decreased to ~220 Pa s (~850°C) when the primary foam collapsed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of glass forming additives on low-activity waste feed conversion to glass

A significant effort was invested in the past to develop and refine mathematical models that relate the composition of nuclear waste glasses with their properties, such as viscosity, electrical conductivity, or chemical durability. However, less attention has been paid to the formulation of the melter feed itself, such as the chemical form and the particle size of the glass forming and modifying additives (GFMA), which have a significant effect on the feed-to-glass conversion process during melting. To address this issue, we systematically changed the mineral composition of a simulated low-activity waste melter feed and inspected its melting behavior. When substituting minerals with corresponding oxides and hydroxides, we found that different alumina sources (kyanite, gibbsite, boehmite, or corundum) had the strongest effect on the feed melting process, whereas the sources of Ca, Mg, and Zr had little effect. Further, the x-ray diffraction analysis showed that the alumina sources differ in their dissolution kinetics: early dissolving alumina sources, such as gibbsite (Al(OH) 3 ) and boehmite (AlO(OH)), increase the transient glass-forming melt viscosity at early stages, when gases still evolve, causing extended foaming, whereas alumina sources that dissolve at high temperatures, such as kyanite (Al 2 SiO 5 ) and corundum (Al 2 O 3 ), keep the transient glass-forming melt viscosity low and lead to a faster foam collapse. Using viscosity-composition relationship to estimate the viscosity of transient glass-forming melts in the primary foaming range, we found that the primary foam began to collapse at 360 to 800 Pa s, and fully collapsed between 65 and 260 Pa s. This result agrees with our previous studies, according to which the glass-forming melt viscosity at the cold cap foam bottom ranged from 24 to 85 Pa s.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Durability testing of actual Hanford waste glasses and their non-radioactive simulant glasses

The low-activity waste (LAW) fraction of Hanford tank waste will be converted to glass at the Waste Treatment and Immobilization Plant (WTP) and disposed on the Hanford site. The chemical durability of LAW glasses has been researched for decades to satisfy contract requirements. Most LAW glass durability data has been generated on non-radioactive simulant glasses fabricated via crucible melts. These non-radioactive glasses were chosen due to safety and cost reasons with confidence that radioactive waste glasses would exhibit similar behavior. To reduce the risk of significant differences in laboratory test response data between WTP melter waste glass and simulant glass, Product Consistency Tests (PCT, i.e., ASTM C1285-21) and Environmental Protection Agency (EPA) 1313 durability tests were performed on actual and simulant LAW glasses fabricated using laboratory-scaled melters. Actual and simulant glass durability test results are presented and statistically compared. Finally, differences in test responses were found to be within experimental uncertainty.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Effect of feed composition on the production of off-gases during vitrification of simulated low-activity nuclear waste

During the vitrification of nuclear waste, hazardous and radioactive emissions are generated from the feed-to-glass conversion reactions, in addition to discharges from forced air bubbling and air inleakage. Although the major gaseous emissions are water vapor, nitrogen, and carbon dioxide, various monitored environmental pollutants are also released, such as nitrogen oxides or sulfur dioxide. In addition, reactions between organics and nitrates in the feed may also form products of incomplete combustion such as carbon monoxide and acetonitrile. Although off-gas emissions are commonly measured during both laboratory- and pilot-scale melter testing, no predictive tool is currently available to a priori estimate the composition of gaseous emissions during nuclear waste vitrification. This work forms a basis for the development of such predictive tool by measuring gas evolution from a broad range of simulated low-activity waste melter feeds using evolved gas analysis data and developing correlations between the feed and off-gas compositions. Using reaction stoichiometry and regression analysis, we demonstrate that next to the content of nitrogen and organic carbon in the feed, the gaseous emissions are affected by the feed reduction-oxidation conditions – the more the feed is reduced, the less nitrogen monoxide, and more carbon monoxide and acetonitrile evolves. In conclusion, the results presented in this work provide a first step towards reducing the amount of expensive physical melter testing and the regression analysis provides a simple tool for rapid optimization of feed composition with respect to off-gas composition.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Microbial interactions with phosphorus containing glasses representative of vitrified radioactive waste

The presence of phosphorous in borosilicate glass (at 0.1 – 1.3 mol % P 2 O 5 ) and in iron-phosphate glass (at 53 mol % P 2 O 5 ) stimulated the growth and metabolic activity of anaerobic bacteria in model systems. Dissolution of these phosphorous containing glasses was either inhibited or accelerated by microbial metabolic activity, depending on the solution chemistry and the glass composition. The breakdown of organic carbon to volatile fatty acids increased glass dissolution. The interaction of microbially reduced Fe(II) with phosphorus-containing glass under anoxic conditions decreased dissolution rates, whereas the interaction of Fe(III) with phosphorous-containing glass under oxic conditions increased glass dissolution. Phosphorous addition to borosilicate glasses did not significantly affect the microbial species present, however, the diversity of the microbial community was enhanced on the surface of the iron phosphate glass. Results demonstrate the potential for microbes to influence the geochemistry of radioactive waste disposal environments with implication for wasteform durability.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Cold-cap structure in a slurry-fed electric melter

We report as glass batch is charged into an electric melter, a cold cap forms on the glass melt surface. Heat transfer to the cold cap from the molten glass below and the melter atmosphere above determines the melting rate. A mathematical model of the cold cap and the experimental kinetic data of the feed-to-glass conversion that were collected for several simulated low-activity and high-level waste melter feeds allowed us to develop relationships between the internal structure of the cold cap, its properties, its thickness, and the internal heat transfer. This contribution shows the distribution of major crystalline phases and the cumulative evolution of gases within the cold cap. It also examines the temperature, conversion degree, and heating rate the melter feed is experiencing during the passage through the cold cap and their effects on the cold-cap bottom temperature and morphology, which are important for the computational fluid dynamics simulations of melters.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Arrhenian to non-Arrhenian crossover in glass melt viscosity

The activation energy for glass melt viscosity is a function of temperature, i.e., non-Arrhenian, within a middle range of viscosity values (typically, between 10 2 and 10 10 Pa s) and constant, i.e., Arrhenian, outside this range. At the low-viscosity end, the Arrhenian to non-Arrhenian transition (termed the crossover) falls within the glass processing range: glass melting and fining occur within the Arrhenian range while glass forming occurs within the non-Arrhenian range. By the Adam-Gibbs equation, the configuration entropy is nearly constant at high temperatures (low viscosities), where the glass melt turns into a simple liquid, and decreases with decreasing temperature (increasing viscosity) as the glass is increasingly polymerized. In the present study, the power-law function and hyperbolic tangent function are used to express the configuration entropy as a function of temperature. The viscosity crossover is defined as the point at which onset of structural grouping is causing the configuration entropy to deviate from its high-temperature value. In conclusion, it appears that the limited range of the configuration entropy of the fully depolymerized melt imposes a restriction on the crossover viscosity; for well-defined glass families, such as float glasses or nuclear waste glasses, the crossover point can be defined using a fixed, i.e., composition-independent, viscosity value.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Chemical durability assessment of enhanced low-activity waste glasses through EPA method 1313

In this work, we report the progress of the Glass Leaching Assessment for Durability (GLAD) program on the implementation of the United States Environmental Protection Agency (EPA) Leaching Environmental Assessment Framework pH-dependent leach test (EPA Method 1313) to low-activity nuclear waste (LAW) glasses. The GLAD program seeks to develop new strategies to understand the chemical durability of nuclear waste glasses for the disposal in near-surface conditions. A series of 16 high-waste loading LAW glasses, currently under development, were selected using machine learning methods to study the corrosion behavior using EPA Method 1313. Reacted glass powders were examined using scanning electron microscopy and the eluate compositions were examined using inductively coupled plasma-optical emission spectroscopy. Compositional modeling was used to fit the measured elemental releases from EPA Method 1313. The compositional models demonstrated that elements such as Si reduce elemental release while B can increase elemental release (consistent with elemental modeling of the Product Consistency Test and Vapor Hydration Test) while other elements, such as Fe, exhibit pH-dependent behavior. The amount of acid added during the EPA testing was found to significantly impact the observed result, which was only apparent after preforming the present matrix study. The overall titration curves were able to be compositionally modeled for future process optimization.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗