Search NASA⌕ Search

Engineering topics

Kruger, Albert A.

Publications and source records attributed to Kruger, Albert A..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effect of material properties on batch‐to‐glass conversion kinetics

Abstract A recently developed model of the cold cap—the reacting glass batch (melter feeds) floating on molten glass in an electric glass melter—couples heat transfer with the feed‐to‐glass conversion kinetics. The model allows for determining the distributions of temperature and various properties within the cold cap. In the present study, this model is applied to four melter feeds designed for high‐level and low‐activity nuclear wastes. Profiles of temperature, conversion degree, cold cap porosity and density, condensed matter velocity, and heating rate were determined using the material properties of the cold cap. Effects of vigorous foaming at the cold cap bottom were considered. Density, thermal conductivity, and glass production rate strongly affect the cold cap thickness and the fraction of undissolved silica entering the melt under the cold cap. The heating rate profile in the cold cap is highly nonlinear, with high heating rates observed in the foam layer.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Alternative reductants for foam control during vitrification of high-iron High Level Waste (HLW) feeds

Foaming during vitrification of radioactive waste in Joule-Heated Ceramic Melters (JHCM) is exacerbated by trapping of evolving gases, such as CO 2 , NO x and O 2 , beneath a viscous reaction layer. Foaming restricts heat transfer during melting. Sucrose is employed as the baseline additive at the Hanford site in Washington State, USA to reduce foaming. Alternative carbon-based reductant additives were explored in simulated, inactive Hanford high-iron HLW-NG-Fe2 feeds, for both their effect on foaming and to give insight to the behaviour of multivalent species in glass melts under different redox conditions. Graphite, coke (93% C), formic acid and HEDTA additives were compared with sucrose, and a feed with no additive. Graphite and coke additions proved most effective in reducing the maximum foam volume by 51 ± 3% and 54 ± 2%, respectively, compared with 24 ± 5% for sucrose. Lower foaming could result in more efficient vitrification in JHCMs. Reductants also affected redox ratios in the multivalent species present in the feed. The order of reduction, Mn 3+ /Mn 2+ > Cr 6+ /Cr 3+ > Ce 3+ /Ce 4+ > Fe 3+ /Fe 2+ was as predicted on the basis of their redox potentials. There is less reduction overall, particularly in the Fe 3+ → Fe 2+ , than predicted by the calculations, attributed to the oxygenated atmosphere of the experiments.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Micro- and Nanoscale Surface Analysis of Late Iron Age Glass from Broborg, a Vitrified Swedish Hillfort

Abstract Archaeological glasses with prolonged exposure to biogeochemical processes in the environment can be used to understand glass alteration, which is important for the safe disposal of vitrified nuclear waste. Samples of mafic and felsic glasses with different chemistries, formed from melting amphibolitic and granitoid rocks, were obtained from Broborg, a Swedish Iron Age hillfort. Glasses were excavated from the top of the hillfort wall and from the wall interior. A detailed microscopic, spectroscopic, and diffraction study of surficial textures and chemistries were conducted on these glasses. Felsic glass chemistry was uniform, with a smooth surface showing limited chemical alteration (<150 nm), irrespective of the position in the wall. Mafic glass was heterogeneous, with pyroxene, spinel, feldspar, and quartz crystals in the glassy matrix. Mafic glass surfaces in contact with topsoil were rougher than those within the wall and had carbon-rich material consistent with microbial colonization. Limited evidence for chemical or physical alteration of mafic glass was found; the thin melt film that coated all exposed surfaces remained intact, despite exposure to hydraulically unsaturated conditions, topsoil, and associated microbiome for over 1,500 years. This supports the assumption that aluminosilicate nuclear waste glasses will have a high chemical durability in near-surface disposal facilities.

Matthews, Bethany E. (ORCID:0000000171932583)↗
DOE OSTI2022

Effect of sucrose on the oxidation-reduction conditions and retention of rhenium during vitrification of low-activity waste

Technetium speciation and solubility during nuclear waste vitrification are affected by oxygen partial pressure in the melt. Thus, reducing agents such as sucrose, which are routinely added to nuclear waste feeds to repress foaming, can significantly affect the volatilization of Tc and increase its retention in glass. Using Re as a surrogate for Tc, we measured the effect of sucrose addition to two low-activity waste melter feeds on the Re retention, oxygen partial pressure, and iron redox as functions of temperature. As expected, Re retention in glass increased as the sucrose content increased. Furthermore, this is attributed to sucrose reaction with nitrates and nitrites in the feed. Destruction of nitrates and nitrites reduces the salt phase fraction and thus likely promotes Re diffusion into the glass-forming melt. In agreement with available literature, we discuss that a modest increase in the sucrose content (compared to current practice) can significantly improve the Tc retention without reducing Fe 2+ to metal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effect of network connectivity on behavior of synthetic Broborg hillfort glasses

There is wide industrial interest in developing robust models of long-term (>100 years) glass durability. Archeological glass analogs, glasses of similar composition, and alteration conditions to those being tested for durability can be used to evaluate and inform such models. Two such analog glasses from a 1500-year-old vitrified hillfort near Uppsala, Sweden have previously been identified as potential analogs for low concentration Fe-bearing aluminosilicate nuclear waste glasses. However, open questions remain regarding the melting environment from which these historic glasses were formed and the effect of these conditions on their chemical durability. A key factor to answering the previous melting and durability questions is the redox state of Fe in the starting and final materials. Past work has shown that the melting conditions of a glass-forming melt may influence the redox ratio value (Fe +3 /ΣFe), a measure of a glass's redox state, and both melting conditions and the redox ratio may influence the glass alteration behavior. Synthetic analogs of the hillfort glasses have been produced using either fully oxidized or reduced Fe precursors to address this question. In this study, the melting behavior, glass transition temperature, oxidation state, network structure, and chemical durability of these synthesized glass analogs is presented. Resulting data suggests that the degree of network connectivity as impacted by the oxidation state of iron impacted the behavior of the glass-forming melt but in this case does not affect the chemical durability of the final glass. Glasses with a lower degree of melt connectivity were found to have a lower viscosity, resulting in a lower glass transition temperature and softening temperature, as well as in a lower temperature of foam onset and temperature of foam maximum. This lower degree of network connectivity most likely played a more significant role in accelerating the conversion of batch chemicals into glass than the presence of water vapor in the furnace's atmosphere. Future work will focus on using the results from this work with outcomes from other aspects of this project to evaluate long-term glass alteration models.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Glass length: Workability and meltability of glass as a function of glass melt fragility

Workability and meltability of molten glass are properties important for balancing glass formulation with the design and operations of glass melting and forming facilities. The working and melting “lengths” are the temperature intervals within which glass viscosity allows the melting and forming glass to be performed. They are related to glass melt structure through the glass melt fragility, which, by the augmented Adam-Gibbs equation, is a function of configuration entropy. Both working length and melting length are high for strong glasses and decrease as the melt fragility increases. In this work, analytical formulas are obtained for three-parameter viscosity models VFT, AM, and MYEGA. These models agree with each other and with the Adam-Gibbs equation on the relationship between workability and fragility of glasses but diverge at high-temperatures. The compositional effects on workability and meltability are mediated via the fragility as a function of glass composition expressed in terms of mass and mole component coefficients.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Conversion degree and heat transfer in the cold cap and their effect on glass production rate in an electric melter

A predictive model of melt rate in waste glass vitrification operations is needed to inform melter operations during normal and off-normal operations. This paper describes the development of a model of the cold cap (the reacting melter feed floating on molten glass in a glass melter) that couples heat transfer with the feed-to-glass conversion kinetics. The model was applied to four melter feeds designed for high-level and low-activity nuclear waste feeds using the material properties, either measured or estimated, to obtain temperature and conversion distribution within the cold cap. The cold cap model, when coupled with a computational fluid dynamics model of a Joule-heated glass melter, allows the prediction of the glass production rate and power consumption. The results show reasonable agreement with the melting rates measured during pilot-scale melter tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effect of sucrose on technetium and rhenium retention during vitrification of low-activity wastes

Sucrose (C 12 H 22 O 11 ) has been used in low-activity waste (LAW) melter feeds containing large fractions of nitrates, nitrites, or both because it facilitates foam suppression and denitration. This study focused on the effect of sucrose in LAW feeds on technetium (Tc) and rhenium (Re) retention. The amount of sucrose added in feeds was varied to differentiate the carbon-to-nitrogen mole ratio (C/N ratio). The results show that larger sucrose addition (higher C/N ratio) enhances Tc and Re retention. Reducing conditions induced by sucrose decomposition and early chemical reactions between sucrose and NaNO 3 /NaNO 2 are expected to increase Tc and Re retention. However, high sucrose addition decreased sulfur (S) retention slightly because sodium sulfate decomposes in reducing conditions at lower temperature. This early sulfate decomposition can affect Tc and Re retention partly because these species can be soluble in sulfate phases. This correlation indicates that the decrease of sulfate phases in the glass by early decomposition can reduce the solubility of Tc and Re in the sulfate phases, which may increase Tc and Re retention in the glass. In addition, continuous gas evolution and vigorous foaming at the foaming temperature range of 700–900°C may influence Tc and Re retention process interrupting retention or facilitating volatilization.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Augmented Adam-Gibbs model for glass melt viscosity and configuration entropy as functions of temperature and composition

As the temperature of glass melt increases, its structure approaches the state of a simple liquid while the configuration entropy approaches a maximum value. We describe this gradual change using a power law function of inverse temperature. The Adam-Gibbs model for glass viscosity as a function of temperature and glass composition augmented in this way is greatly simplified when applied to common glass families occupying moderate composition regions, such as float glass or nuclear waste glasses, on which properties can be approximated as linear functions of composition. The parsimonious model thus obtained is preferable for use in optimizing glass formulation and mathematical modeling of glass melting and forming. For multicomponent glasses with N viscosity-affecting components, the augmented Adam-Gibbs model requires 2N + 3 adjustable parameters. The model efficacy is demonstrated by fitting the model to a viscosity-temperature-composition dataset for low-activity nuclear waste glasses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Assessment of the reason for the vitrification of a wall at a hillfort. The example of Broborg in Sweden

It was discovered around 250 years ago that some of the rock material in the walls of some hillforts had been subjected to such high temperature that it had vitrified. This prompted a debate as to the reason for it that is still going on today: did the vitrification come about as a result of hostile action, by accident, or for the purpose of constructing the fort? The present paper is based on the prerequisite that hillforts are different, and therefore should be evaluated individually. All identifiable factors of interest should be included, and especially those that might disprove any alternative. Thus, incentives, competence and petrographic aspects were evaluated for the hillfort Broborg (dated Migration Period, in Sweden A.D. 400 - 550), and it is concluded that the vitrification came about for the purpose of constructing the fort. This capability was lost when mortar was introduced half a millennium later.

42 ENGINEERING↗
DOE OSTI2022

Hanford low-activity waste glass composition-temperature-melt viscosity relationships

This study developed a model for predicting viscosity of alkali-alumino-borosilicate glass melts as functions of composition and temperature. The model is based on a total of 3935 viscosity-temperature data from 574 glasses with viscosity values ranging from 2.53 to 7260 Poise (P) in the temperature range of 900–1260°C. Several different model forms were surveyed, including those based on Arrhenius, Vogel-Fulcher-Tammann, Avramov-Milchev, and Mauro-Yue-Ellison-Gupta-Allen. For each of these models, combinations of the temperature-independent parameters were fitted to composition. It was found that generally fitting more than one temperature-independent parameter as functions of composition resulted in overfitting. The Avramov-Milchev-based model was found to best represent the Hanford low-activity waste glass melt viscosity data based on model fit and validation statistics. A 21-term partial quadratic mixture model was recommended for use. This model predicts melt viscosity with a root-mean square error of .1736 ln(P), which is similar to the error in viscosity measurements from replicate glass analyses of .1383 ln(P). Viscosity was found to be most increased by SiO 2 > Al 2 O 3 > ZrO 2 > SnO 2 and most decreased by Li 2 O > Na 2 O > B 2 O 3 > CaO > K 2 O > MgO, at temperatures from 900 to 1260°C.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Metallic Technetium Sequestration in Nickel Core/Shell Microstructure during Fe(OH)2 Transformation with Ni doping

This study investigates the impacts of Ni doping on technetium-99 (Tc) sequestration in aqueous solutions through transformation of Fe(OH)2(s) to iron spinel (magnetite) under alkaline conditions. Extensive solid characterization was performed for the mineral phases produced, as well as the Tc/Ni speciation and distribution within these phases. X-ray diffraction results show that iron spinel was the dominant mineral product without detectable Ni incorporation. The doped Ni ions mainly precipitated as fine Fe/Ni oxide/hydroxide particles, including strongly reduced nanometer?sized spheroidal Ni-rich and metallic Ni phases. High-resolution analytical scanning transmission electron microscopy using energy dispersive X-ray spectroscopy and electron energy loss spectroscopy on the produced solid samples (focused ion beam-prepared specimens) revealed three Tc distribution domains dominated by nanocrystals and, especially, a Tc-rich metallic phase. Instances of metallic Tc were specifically found in spheroidal, Ni-rich and metallic nanoparticles exhibiting a core/shell microstructure that suggests strong reduction and sequential precipitation of Ni-Tc-Ni. Mass balance analysis showed nearly 100% Tc removal from the 4.8 × 10-4 M Tc solutions. The finding of the metallic Tc encapsulation indicates that Tc sequestration through Ni-doped Fe(OH)2(s)?to?iron spinel transformation process likely provides an alternative treatment pathway for Tc removal and could be combined into further waste treatment approaches.

Wang, Guohui↗
DOE OSTI2022

Volatility of sodium, potassium, and cesium perrhenates determined by thermogravimetry

Here, in this study, we investigated the volatility of sodium, potassium, and cesium perrhenates using thermogravimetry (TG) performed on single salts and their binary mixed salts. We performed simultaneous TG and differential scanning calorimetry under a ramp heating condition at 10°C/min up to 1200°C to characterize volatilization behavior as a function of temperature. We also performed isothermal TG over a temperature range of 700 to 975°C to estimate the vapor pressures of the alkali perrhenates based on a modified Langmuir equation that relates the rate of free evaporation from the open surface to vapor pressure. In this paper, we discuss the results of our study on the temperature of evaporation and temperature-dependent vapor pressure of sodium, potassium, and cesium perrhenates in relation to rhenium volatilization behavior observed during melting of simulated waste glass.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Conversion kinetics during melting of simulated nuclear waste glass feeds measured by dissolution of silica

In this work, we experimentally investigated the batch-to-glass conversion kinetics of two low-activity and two high-level nuclear waste melter feeds that represent widely different behavior during melting; tests comprised thermogravimetric analysis, the feed expansion test, evolved gas analysis, and x-ray diffraction. Our study indicates that the conversion processes, which include gas-evolving reactions, dissolution of crystalline phases, and primary foam expansion and collapse, are interconnected and influenced by the feed’s thermal history. The fraction of dissolved silica was adopted as a measure of the extent of conversion inside the cold cap—the floating layer of feed material on the top surface of the melt in an electric melter. The interface between the cold cap and the free-flowing melt below was associated with a constant fraction of dissolved silica. The estimated viscosity of glass-forming melt at this interface lies within a narrow range for the feeds studied.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

In-situ X-ray and visual observation of foam morphology and behavior at the batch-melt interface during melting of simulated waste glass

We report to attain a basic understanding of the primary foam structure and behavior, which affects the heat and mass transfer and the efficiency of the glass melting process, we investigated the primary foam layer under the glass batch floating on molten glass. The primary foam affects mass transfer during batch melting, in turn affecting the melting process. The recently performed direct in-situ three-dimensional X-ray computed tomography of the batch melting in a laboratory-scale melter vessel allowed us to visualize the features of the reacting batch layer and the foam that develops at its bottom, though with an insufficient resolution of images. In this study, we obtained better temporal and spatial resolution using the two-dimensional X-ray radiography and visual observation of the structure and behavior of transient primary foam as it formed and decayed. As soon as the batch was charged onto the melt surface, foam bubbles began to evolve, grow, and coalesce, forming a primary foam layer, 5-10 mm thick, within tens of seconds. This foam layer was sustained by ongoing gas evolving reactions counterbalanced by bubble coalescence into cavities that moved sideways and escaped to the atmosphere. Eventually, the entire remaining batch turned into foam that gradually decayed at the melt surface. The decay rate agreed with literature observations of surface foam produced by secondary foaming.

36 MATERIALS SCIENCE↗