Engineering topics

Lance, Michael [ORNL] (ORCID:0000000151675452)

Publications and source records attributed to Lance, Michael [ORNL] (ORCID:0000000151675452).

5 records

DOE OSTI2026

FLiBe compatibility of fusion-relevant materials

There is current interest in a 2LiF-BeF2 (FLiBe) molten salt blanket for fusion applications, however, very little compatibility data are available for fusion relevant materials. Initial static capsule testing results for 500 h at 550°-750 °C are presented for V-4Cr-4Ti, Fe-8Cr-2W (alloy F82H) compared to type 316H stainless steel and monolithic SiC as a surrogate for SiC/SiC composites. In addition, sintered Be12Ti specimens with varying additions of Be (0–20%) and a Be2C specimen were exposed with F82H coupons at 650 °C in individual Mo capsules. The V-4Cr-4Ti and SiC specimens exposed at 650 °C had small mass changes. Steel specimens showed increasing mass losses with increasing exposure temperature. However, when Be12Ti-Be specimens were included in a capsule with an F82H coupon, increasing F82H mass gains were observed with increasing Be content due to the formation of a Fe-Be surface layer. No layer and no mass gain were observed for the F82H specimen tested with Be2C.

Pint, Bruce [Oak Ridge National Laboratory (ORNL) ↗

DOE OSTI2026

High pressure effects on EBC systems in high temperature environments

Environmental barrier coatings (EBCs) are designed to protect SiCfiber/SiCmatrix ceramic matrix composites (CMCs) in turbine engines by mitigating wear in high-temperature water vapor environments. The failure of EBCs is frequently attributed to the accelerated oxidation of the silicon bond coating layer when exposed to high-temperature steam, leading to the formation of a thickened thermally grown oxide (TGO). TGO growth increases interfacial stress, weakens adhesion, and results in coating spallation. Understanding the impact of high-temperature oxidation of EBC systems is essential for developing accurate lifespan models for turbine components, although pressurized oxidation testing is extremely sparse in the open literature. In this work, oxidation tests were performed on rare earth silicate EBCs coated onto SiC substrates under increased pressure conditions. The coated specimens were tested at 1100°C, 1200°C, and 1300°C at both 1 atm and 10 atm total pressure in steam environments. Subsequent characterization focused on the microstructural evolution of the EBC/Si/SiC system. The experimental findings indicated that TGO behavior is dependent on high-pressure conditions, with elevated pressure leading to an increase in oxide scale thickness and modifications in its morphology.

Ardrey, Kristyn [ORNL] (ORCID:0000000184407796)↗

DOE OSTI2026

Impact of nitrogen on lithium-induced corrosion and cracking of RAFM steel

The emergence of private fusion enterprises, combined with advancements in U.S. and EU ITER-TBM as well as EU DEMO liquid breeder blanket concepts, has renewed focus on the materials challenges. This study examines the compatibility of reduced activation ferritic/martensitic (RAFM) steel in liquid Lithium (Li) containing various Nitrogen (N) concentrations, tested at 600 and 700 °C for 500 and 1000 h under static conditions. Microstructural characterization revealed the corrosion-induced dissolution and precipitation in Li containing 0.082 and 0.17 wt.% N at 600 °C, while limited dissolution and precipitation were observed in N-gettered Li using zirconium (Zr) and titanium (Ti) foils at 600 °C. Tensile testing at room temperature after Li exposure revealed a decrease in strength and ductility of the RAFM steel as a function of N content in Li. Severe embrittlement was observed after 500 h in Li containing 0.17 wt.% N at 600 °C and after 500 h in hot-gettered Li at 700 °C. Chromium (Cr) depletion from the steel matrix was observed, leading to the formation of M6C-type carbides on the surface identified by electron microscopy (SEM), X-ray diffraction (XRD), in agreement with thermodynamic calculations. These findings highlight the critical materials challenges posed by liquid Li breeder blanket concepts, emphasizing the need for improved strategies to address Li-induced dissolution, precipitation, and steel embrittlement due to N contamination of the coolant.

Romedenne, Marie [ORNL] (ORCID:0000000317936561)↗

DOE OSTI2026

Porous reaction-bonded silicon nitride: Size effects for pressureless nitriding of binder jet additively manufactured silicon

The direct nitridation of binder jet additively manufactured silicon to produce porous reaction-bonded silicon nitride was explored to determine the maximum thickness of the sample that could be converted to >99% silicon nitride. The maximum thickness that could be nitrided was investigated by nitriding cubes of increasing physical size on the millimeter scale. Highly porous samples with high conversion ( > 99%) to silicon nitride were achieved in cubes with 35 mm edge length. It was shown that the silicon nitride phase content changes with increasing sample size.

Aguirre, Trevor [ORNL] (ORCID:0000000281469630)↗

DOE OSTI2026

Additively Manufactured Carbon Fiber-Reinforced Siliconized Silicon Carbide Composites Using Carbon Fiber-Reinforced Poly-Ether-Ether-Ketone (PEEK) as a Precursor

Herein, we report a method to additively manufacture carbon fiber-reinforced siliconized silicon carbide composites. The process involves the pyrolysis of a 3D-printed carbon fiber-reinforced poly-ether-ether-ketone (PEEK) composite to produce a porous carbon fiber-reinforced carbon matrix composite preform, which is subsequently infiltrated with molten silicon to obtain a carbon fiber-reinforced siliconized silicon carbide composite. A key aspect of the method is limiting polymer melt flow during pyrolysis of PEEK, which is achieved by thermally annealing the 3D-printed carbon fiber-reinforced PEEK preform in air at a temperature below PEEK’s melting temperature. Rheological and differential scanning calorimetry (DSC) measurements demonstrate that the thermal annealing treatment altered the melting behavior of PEEK, while NMR and FTIR measurements provided a mechanistic explanation for the structural changes responsible for the behavior. It was also found that dimensional changes during pyrolysis were anisotropic with greater shrinkage in the stacking direction of the material.

Yoon, Bola [ORNL] (ORCID:0000000260875373)↗