Assessing Stainless Steel Compatibility in Flowing Fluoride Salts
Explore the source record for details and available documents.
Pint, Bruce↗
Engineering topics
Lance, Michael J.
Publications and source records attributed to Lance, Michael J..
Steam oxidation and microstructural evolution of rare earth silicate environmental barrier coatings
A primary failure mode for environmental barrier coatings (EBCs) on SiC ceramic matrix composites (CMCs) is the oxidation of the intermediate Si-bond coating, where the formation of SiO 2 at the bond coating–EBC interface results in debonding and spallation. This work compares the microstructure evolution and steam oxidation kinetics of the Si-bond coating beneath yttrium/ytterbium disilicate ((Y/Yb)DS) and ytterbium disilicate/monosilicate (YbDS/YbMS) EBCs to better understand the impact of EBC composition on oxidation kinetics. After 500 1-h cycles at 1350°C, (Y/Yb)DS displayed a decreasing concentration of the monosilicate minor phase and increasing concentration of porosity as furnace cycling time increased, whereas the YbDS/YbMS EBC displayed negligible microstructural evolution. For both EBC systems, thermally grown oxide growth rates in steam were found to increase by approximately an order magnitude compared to dry air oxidation. The (Y/Yb)DS EBC displayed a reduced steam oxidation rate compared to YbDS/YbMS.
36 MATERIALS SCIENCE↗
The Effect of APS-HVOF Bond Coating Thickness Ratio on TBC Furnace Cycle Lifetime
In this work, combinations of NiCoCrAlY APS and high-velocity oxygen fuel (HVOF) bond coatings were deposited on alloy 247 disk substrates with APS yttria-stabilized zirconia (YSZ) top coatings to assess the benefit of air plasma sprayed (APS) ‘flash’ bond coatings. Using 1-h cycles at 1100 °C in air with 10% H 2 O and HVOF-only and APS-only bond coatings as a baseline, it was found that APS flash coatings extended the average coating lifetime by 16% to 35% with the thicker flash coating performing best. Principal component analysis and energy dispersive spectroscopy (EDS) compositional mapping on coatings characterized after 0, 100, 300 and 500 cycles and after failure showed that the Al in the bond coatings was depleted due to both oxidation and back diffusion into the substrate. The APS-only bond coating had significant oxidation throughout the bond coating and was so depleted in Al, that Al diffused from the substrate to the coating. Residual stress maps of the thermally-grown alumina scale were obtained every 100 cycles using photo-stimulated luminescence piezospectroscopy (PLPS) revealing that the Thick Flash coating had the slowest rate of damage accumulation in the oxide scale.
alumina scale↗
Leveraging computational thermodynamics to guide SiC-ZrC chemical vapor deposition process development
Here using the CALPHAD approach to understand zirconium carbide deposition, a series of phase equilibria were calculated from a custom thermodynamic database based on a literature source, and the equilibria were used to explore the potential chemical vapor deposition (CVD) processing space in the ZrCl 4 -CH 3 SiCl 3 -CH 4 -H 2 system as a function of pressure, temperature, and gas composition. Several gas ratios were considered. At a given ZrCl 4 :CH 3 SiCl 3 ratio within the range studied, the most important factor was found to be the ratios of CH 4 :ZrCl 4 , wherein the nature of the composition – carbide vs. silicide – could be controlled. A pure binary composition of ZrC and SiC is expected to form by increasing the initial amount of methane and decreasing the amount of hydrogen from values predicted purely based on thermodynamic equilibrium. Rietveld analysis of the x-ray diffractograms from corresponding experimental depositions confirmed that increasing the CH 4 :ZrCl 4 ratio increased the fraction of carbon-containing species (SiC, ZrC) and decreased the fraction of non-carbides (ZrSi, ZrSi 2 , etc.), as predicted from the CALPHAD results.
36 MATERIALS SCIENCE↗
Compatibility of 316H in Static and Flowing FLiBe and FLiNaK Salts at 550°-650°C
Explore the source record for details and available documents.
Sulejmanovic, Dino↗
Hydrothermal corrosion and steam oxidation behavior comparison of UAM and conventional Zry-4
Here, hydrothermal corrosion and steam exposures on ultrasonic additively manufactured (UAM) Zircaloy-4 (Zry-4) specimens were conducted to compare to wrought Zry-4 performance in both simulated pressurized water reactor (PWR) operation (330°C, 15 MPa, <50 ppb oxygen, 500h) and representative accident conditions (100% H 2 O(g) at 700, 900, and 1100°C for up to 1h). UAM Zry-4 specimens showed 50% higher mass gain in PWR conditions and 50-80% more mass gain in steam oxidation due to internal oxidation between build layers in both cases. UAM Zry-4 in 900°C steam showed breakaway oxidation leading to sample deformation. Titanium used as an interlayer in the UAM process was detected in the substrate after the 1100°C exposure. Additional experiments to better link as-built defects to oxidation behavior are needed.
36 MATERIALS SCIENCE↗
Interaction of beryllium with 316H stainless steel in molten Li 2 BeF 4 (FLiBe)
The increased demand in renewable energy resources has led to a renewed interest in nuclear reactors including a new generation of molten salt reactors. One of the issues encountered in handling of molten chloride or fluoride salts is the inability of metals to form and retain a protective oxide surface layer, generally chromium oxide. The low chromium content, nickel-based alloy INOR-8, later marketed as Hastelloy N, was specifically developed to contain molten fluorides. This alloy had some deficiencies, but its composition resulted in it incurring far less chromium depletion by the molten fluoride salts than alloys like 316 stainless steel. For the next generation of molten salt reactors, an alloy with pressure vessel code approval and higher temperature capability than Hastelloy N is required. Consequently, several reactor designers have reportedly chosen to build the reactor containment vessel from 316H stainless steel. In order to minimize corrosion of the stainless steel by the molten fluoride salt (2LiF-BeF 2 ), it is proposed to add beryllium metal to the salt to react with impurities and provide a means to lower the oxidation potential thus making the salt less corrosive. Even so, there is a concern whether the beryllium would react with components of the stainless steel. To address this concern, static capsule tests were conducted in which selected amounts of beryllium were added to capsules containing 2LiF-BeF 2 (FLiBe) salt and 316H stainless steel and Hastelloy N samples. Following exposure, the samples were cleaned and examined using a variety of analysis techniques including, optical microscopy, SEM-EDS, XPS, LIBS, XRD and EPMA. Tensile samples were also exposed in capsules, and those were subjected to tensile testing. Notably, It was found that for the level of beryllium additions used in this study, intermetallic compounds were formed which could be detrimental to the long-term performance of the 316H stainless steel.
36 MATERIALS SCIENCE↗
Creep Behavior and Phase Equilibria in Model Precipitate Strengthened Alumina-Forming Austenitic Alloys
Abstract Creep-rupture behavior and microstructural response in alumina-forming austenitic (AFA) alloys with two different precipitation strengthening mechanisms, “Laves-phase + M 23 C 6 carbide” and “coherent L1 2 γ′-Ni 3 (Al,Ti),” were explored as “model” cases of multi-phase, multi-scale heat-resistant AFA alloys for 650–750°C use. These alloys will be used to guide and verify computational alloy design and life-prediction modeling under an on-going eXtremeMAT project through the Office of Fossil Energy and Carbon Management, US Department of Energy. Computational thermodynamics were used to design and predict the amounts of strengthening and deteriorating secondary phases at 750°C. Creep-rupture lives of the alloys tested at 750°C and 100 MPa were in a range of 4000–9000 h, and the microstructure at the gage/grip after creep-rupture testing was compared with isothermally aged alloys for 1500 h, as well as the calculated phases. Detailed microstructure characterization includes phase identification, volume fraction measurement, and compositional analysis, which were correlated with the creep-rupture properties. High-temperature oxidation resistance was also screened and compared with commercial, chromia-forming heat-resistant steels. These model alloys also provide the basis for further design and optimization of next generation AFA alloys with improved creep resistance.
36 MATERIALS SCIENCE↗
Compatibility Of Steels At 450°-650°C In Supercritical CO2 With O2 And H2O Additions
Direct-fired supercritical CO2 (sCO2) power cycles are being commercialized to revolutionize fossil energy as a low-emission power source. However, the cycle will increase O2 and H2O in the sCO2 and the implications of these additions have not been fully studied, particularly for lower cost steels that are needed in the lower temperature segments of the plant. Representative 9 and 12%Cr ferritic-martensitic (FM) steels and conventional and advanced austenitic steels were evaluated at 450-650°C to determine the maximum use temperatures in sCO2 with 1%O2 and 0.1%H2O at 300 bar. Compared to research grade (low impurity) sCO2 in indirect-fired cycles, the mass gains and scale thickness were not significantly changed for FM steels: both formed thick duplex Fe-rich scales. For stainless steels, higher mass gains were observed in all cases with increased Fe-rich oxide nodule formation. After 1000h at 650°C, the measured bulk C content was high for all of the steels with the addition of impurities suggesting a lower maximum operating temperature for steels. The post-exposure impact of the environment on room temperature tensile properties also will be discussed.
Pint, Bruce↗
Dry air cyclic oxidation of mixed Y/Yb disilicate environmental barrier coatings and bare silica formers
Here mixed Y and Yb disilicate coatings (Y/Yb)DS have been proposed as dual function thermal and environmental barrier coatings (EBCs) for protecting SiC-based ceramic matrix composites in gas-turbine environments. As an initial step, the 1350 °C dry air cyclic oxidation of atmospheric plasma sprayed (Y 1.2 /Yb 0.8 )DS and ytterbium disilicate/ytterbium monosilicate (YbDS/YbMS) EBCs deposited onto Si bond coatings was compared. As a baseline for evaluating EBC oxidant permeability, the dry air cyclic oxidation scale growth rates for bare silica formers (SiC, Si) were also measured and were consistently higher than rates previously measured after isothermal oxidation. Regarding Si bond coat oxidation rates underlying (Y/Yb)DS and YbDS/YbMS EBCs, the thinner silica scale formed under the thinner and denser (Y/Yb)DS coatings suggested a lower oxidant permeability than YbDS/YbMS. After 500 1-h cycles, the (Y/Yb)DS coating was comprised of only the β-polymorph disilicate and minor amounts of the X-2 phase monosilicate phase. Negligible differences in oxidation kinetics for (Y/Yb)DS coatings over the 90 – 240 µm thickness range were observed.
36 MATERIALS SCIENCE↗
Evolution of the structure and chemical composition of the interface between multi-component silicate glasses and yttria-stabilized zirconia after 40,000 h exposure in air at 800 °C
The chemical and structural stability of two commercial multicomponent silicate glasses (SCN and G6) in contact with yttria-stabilized zirconia (YSZ) was investigated after exposure times of up to 40,000 h in air at 800 °C. With exposure time, interfacial layers develop at the SCN-YSZ and G6-YSZ interfaces, which were characterized in detail using both quantitative chemical analysis and atomic-resolution imaging. At the SCN-YSZ interface, a Ca-Ba-Si-O reaction phase was found to grow by diffusion control. In G6-YSZ, Raman spectroscopy and electron microscopy revealed a disorganized interfacial reaction later between G6 and YSZ, and the occurrence of cubic to tetragonal to monoclinic phase transformations in YSZ. Finally, this microstructural evolution is discussed in terms of devitrification resistance of glass and diffusion processes at interfaces.
36 MATERIALS SCIENCE↗
Evaluating steam oxidation kinetics of environmental barrier coatings
Environmental barrier coatings (EBCs) are a commercially proven means of protecting SiC-based materials in gas turbine environments. However, there are little specific data in the literature on the impact of coatings like Yb 2 Si 2 O 7 on preventing accelerated SiO 2 growth in the presence of H 2 O. Quantification of reduced rates are necessary for evaluating and comparing EBC effectiveness and incorporation of silica growth rates into future EBC lifetime models. In this study, baseline kinetics of silica formation on bare Si and chemically vapor deposited (CVD) SiC in the 1250–1425 °C range were obtained via 100 h isothermal exposures in dry air and steam environments utilizing a SiC reaction tube to mitigate specimen volatility. An Arrhenius plot of the resulting rates was constructed, representing baseline minimum and maximum rates for Si and SiC oxidation at ambient pressure. Various EBC systems on CVD SiC substrates including air plasma sprayed (APS) EBCs with and without a Si bond coating and with surface roughening to enhance Yb 2 Si 2 O 7 adhesion were subjected to 1-h furnace cycle testing in air with 90vol%H 2 O at 1250–1350°C for up to 500 cycles. After exposure, silica formation rates were measured and compared to the baseline rates to assess EBC effectiveness, where EBC effectiveness is gauged as the propensity to reduce underlying rates of silica formation. With a Si bond coating, a ~180 µm Yb 2 Si 2 O 7 (YbDS) top coating reduced rates over the entire 1250°-1350°C range. Without a Si bond coating, ~60 µm (YbDS) coatings deposited directly onto CVD SiC exhibited poor adhesion, and had to be deposited onto substrates with enhanced roughness at 1350°C. Finally, while exhibiting good adhesion at 1350°C, overall the single layer YbDS coating exhibited a decreasing effectiveness from 1250° to 1350°C.
36 MATERIALS SCIENCE↗
Testing and Modeling of Functionally Graded Aluminum-Doped Zinc Oxide Using Spark Plasma Sintering and Discrete Powder Layers of Varying Composition
Functionally graded material (FGM) ZnO is made via spark plasma sintering/field-assisted sintering technique (SPS/FAST) by varying the Al dopant content along the z-axis or pressing direction. A wide range of Al content (0–5 wt%) is used by adding Al powder to nanosized ZnO powder. Thermoelectric (TE) measurements are done on the FGM and individual layers made separately. X-ray diffraction (XRD) shows two phases, ZnO and spinel phase (ZnAl 2 O 4 ). High-resolution Raman spectroscopy reveals doped ZnO and spinel phase (ZnAl 2 O 4 ) spatially and shows segregation in the layer with highest Al content. Electron backscatter diffraction (EBSD) reveals noticeable grain growth with decreasing Al content, and there is a common, random preferred orientation in all layers. The tested properties are used to simulate efficiency curves for a discretely graded, five-layer FGM as well as a homogenous material, where both graded structures provide an opportunity to widen the current density ranges and therefore the temperature range of useful energy conversion.
36 MATERIALS SCIENCE↗
Processing and microstructure of ZrB 2 –SiC composite prepared by reactive spark plasma sintering
In-situ formation of ZrB 2 –SiC composites was investigated by reactive spark plasma sintering of precursor powders according to the reaction B4C + 2ZrC + 3Si → 3SiC + 2ZrB 2 . The reaction and process presented here involves a diffusion reaction between B4C and ZrC which facilitates the formation of ZrB 2 , while liquid phase sintering of silicon facilitates atomic diffusion and combines with free C from the B4C and ZrC reaction to form SiC within minutes of heating and there were some residual unreacted precursor materials. An interpenetrating matrix of ZrB 2 –SiC was formed that shows increased fracture toughness (6.03 ± 0.45 MPa m 1/2 ) despite relatively low density (95 %).
36 MATERIALS SCIENCE↗
Deactivation trends of Pd/SSZ-13 under the simultaneous presence of NO, CO, hydrocarbons and water for passive NO x adsorption
Pd-functionalized chabazite (Pd/SSZ-13) was evaluated for passive NO x adsorption (PNA) using low temperature combustion with diesel (LTC-D) reaction feed of the “United States Driving Research and Innovation for Vehicle efficiency and Energy sustainability” (U.S.DRIVE) protocol. Notably as per the protocol conditions, 12% O 2 + 6% CO 2 + 6% H 2 O was flown in all cases. NO-uptake studies in the presence of the LTC-D feed showed a systematic decline with (NO:Pd)molar changing from 0.5 to 0.4 after 10 trials. Control experiments showed more pronounced decline for NO + CO case, with appreciable intial (NO:Pd)molar value of 0.4 yet comparable-to-the-LTC-D-feed decline after 8 trials. CO-induced particle formation and larger extent of particle sintering was also evident from TEM analysis. Other controls did not exhibit trial-dependent deactivation as(NO:Pd)molar values were constant, at 0.3, 0.2, 0.5 and 0.2 for the NO, NO+H 2 , NO + unsaturated hydrocarbon (C 2 H 4 , C 3 H 6 ) and NO + saturated HC (C 3 H 8 , C 10 H 22 ) feeds respectively. In addition to these quantitative differences, desorption behaviors are qualitatively different. While only one major desorption event is observed for the full LTC-D, NO+ CO and NO+ unsaturated HC-controls, desorption occurs in two distinct stages for NO, NO + saturated HCs and initial-NO+H 2 trials. This arises due to inherent differences in Pd sites while exposed to these chemically distinct feeds. Furthermore, presence of reducing agents such as CO and unsaturated HCs in the feed result in almost complete elimination of lower, sub-200 °C desorption peak. The higher temperature desorption peaks, at > 300 °C is associated with NO strongly bound to ionic Pd sites and are prevalent under reducing conditions. Using DRIFTS also, three complexes leading to PNA are assigned, [O = N–Pd 2 +(OH)–Z], [O = N–Pd 2 +(Z2)] and [O = N–Pd 2 +(H 2 O)y–Z] with the latter being clearly observed upon water exposure. Pd/SSZ-13 showed higher hydrocarbon trapping than the SSZ-13 counterpart.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Impact of Primary and Secondary ZDDP and Ionic Liquid as Lubricant Oil Additives on the Performance and Physicochemical Properties of Pd-Based Three-Way Catalysts
In the present study, two industry primary and secondary zinc dialkyldithiophosphate standards, ZDDP1 and ZDDP2, respectively, are evaluated for their impact on the performance of Pd-based three-way catalyst and bench-marked against two mixed lubricant additives formed from either ZDDP1 or ZDDP2 with a second-generation oil-miscible phosphoric-containing ionic liquid (IL). The three-way catalysts (TWCs) are exposed to the lubricant additives in an engine bench under four different scenarios: a base case with no additive (NA), ZDDP1, IL+ZDDP1, ZDDP2, and IL+ZDDP2. The engine-aged TWC samples are characterized through a variety of analytical techniques, including evaluation of catalyst reactivity in a bench-flow reactor. With respect to the water–gas shift reaction and the oxygen storage capacity, the ZDDP2- and IL+ZDDP2-aged TWC samples are more degraded than the ZDDP1- and IL+ZDDP1-aged TWC samples. X-ray diffraction (XRD) patterns indicate that phosphorus in the form of CePO4 was found to be present in the washcoat of all TWC samples, with the highest amount found in the ZDDP2-aged TWC sample. The results obtained from XRD are further confirmed by those from inductively coupled plasma-optical emission spectroscopy (ICP-OES), which show that more phosphorus is detected in the washcoat of ZDDP2- and IL+ZDDP2-aged TWC samples than in the ZDDP1- and IL+ZDDP1-aged TWC samples.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Evaluating the efficacy of aluminide coatings to improve oxidation resistance of high performance engine valve alloys
Increasing peak cylinder pressures and operating temperatures of turbo-charged internal combustion engines (ICEs) engines present new challenges for existing materials employed in engine exhaust valves. Oxidation induced degradation of current Ni based alloys for these components will be a life-limiting mechanism while strict cost margins in the automotive transportation industry further limit the choice of suitable candidate materials. Metallic diffusion aluminide coatings can provide a cost-effective way to improve the oxidation resistance of underlying materials. In this study, the high temperature oxidation behavior of diffusion nickel aluminide coatings on two Ni based alloys (commercially available alloy 31V and a developmental alloy) during cyclic oxidation behavior in air+10% H 2 O at 900 °C was investigated. A complete depletion of the beneficial Al-rich β-(NiFe)Al phase was observed in the coating on alloy 31V while a significant fraction of this phase was retained in the coating on the second alloy. A coupled thermodynamic-kinetic model showed that the disappearance of the Al-rich phase in the coating on 31V was mainly due to the combined effect of steeper chemical potential gradients of Al and Ti between the coating and the substrate and their faster diffusivities compared to the coated developmental alloy. Finally, a higher content of Fe was shown to support the retention of β-(NiFe)Al phase in the coating on the developmental alloy while the presence of Ti in the alloy was shown to be detrimental for long-term coating performance.
36 MATERIALS SCIENCE↗
Hydrothermally stable Pd/SiO 2 @Zr Core@Shell catalysts for diesel oxidation applications
Hydrothermally stable diesel oxidation catalysts (DOCs) with improved low-temperature activity are desired for the abatement of emissions from diesel vehicles. Herein, novel palladium(Pd)/SiO 2 (core)@Zr(shell) structured DOCs were developed. SiO 2 was completely covered by an 8.4 nm thickness Zr-based shell using a hard template method. The SiO 2 @Zr support was decorated by Pd and evaluated under a simulated diesel exhaust stream. Degreened 1 wt% Pd/SiO 2 @Zr achieved 90% CO and total hydrocarbon conversion at 178 and 372 °C, respectively (feed: 6% CO 2 , 12% O 2 , 6% H 2 O, 400 ppm H 2 , 2000 ppm CO, 100 ppm NO, 1667 ppm C 2 H 4 , 1000 ppm C 3 H 6 , 333 ppm C 3 H 8 ; HCs in C 1 basis and GHSV = 113,000 h –1 ). After hydrothermal aging, only a minor deactivation was observed, while the surface area of 1 wt% Pd/SiO 2 @Zr was as high as 104 m 2 /g. The hydrothermal stability of 1 wt% Pd/SiO 2 @Zr was attributed to the poor crystallinity of SiO 2 @Zr, possibly due to the formation of Si-O-Zr bonds. Lastly, this work highlights the promising potential of utilizing durable Pd/SiO 2 @Zr catalysts for diesel oxidation applications.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗