Engineering topics

Lance, Michael J.

Publications and source records attributed to Lance, Michael J..

50 records · Page 3

DOE OSTI2021

Properties of SiC-Si made via binder jet 3D printing of SiC powder, carbon addition, and silicon melt infiltration

In this work, we report the physical and mechanical properties of ceramic composite materials fabricated by binder jet 3D printing (BJ3DP) with silicon carbide (SiC) powders, followed by phenolic resin infiltration and pyrolysis (IP) to generate carbon, and a final reactive silicon melt infiltration step. After two phenolic resin infiltration and pyrolysis cycles; porosity was less than 2%, Young's modulus was close to 300 GPa, and the flexural strength was 517.6 ± 24.8 MPa. However, diminishing returns were obtained after more than two phenolic resin infiltration and pyrolysis cycles as surface pores in carbon were closed upon the formation of SiC, resulting in reaction choking and residual-free carbon and porosity. The instantaneous coefficient of thermal expansion of the composite was found to be independent of the number of phenolic IP cycles and had values of between 4.2 and 5.0 ppm/°C between 300 and 100°C, whereas the thermal conductivity was found to have a weak dependence on the number of phenolic IP cycles. While the manufacturing procedures described here yielded highly dense, gas impermeable, siliconized SiC composites with properties comparable to those of bulk siliconized silicon carbide processed according to conventional techniques, BJ3DP enables the manufacture of objects with complex shape, unlike conventional techniques.

36 MATERIALS SCIENCE↗

DOE OSTI2021

High Temperature Oxidation Behavior of Fe- and Ni-Based Alloy Foils in Water Vapor at 850 °C

Operating temperatures above 700°C are desired to improve the efficiency of power generation systems such as microturbines. Therefore, the use of creep-resistant Ni-based or Fe-based alloys, which can form protective Cr2O3 and Al2O3 scales, is required. In this paper, Fe- and Ni-based alloy foils were oxidized in air + 10 % H2O for up to 3,000 h at 850°C to identify the most promising alloys. The thickness and chemical composition of the spinel oxide formed on top of the Cr2O3 scale varied between S3100, N08120 and N06230 alloy foils. In addition, the rate of Cr and Mn loss (spinel and Cr2O3 oxidation and volatilization) or Al loss (oxidation) and the dissolution of strengthening precipitates, were found to be a function of the nature of the formed oxide (Fe or Ni-rich spinel, Cr2O3, Al2O3). Alloys N06230 and alumina-forming austenitic (AFA) steels were found to be well-suited for the applications as microturbine recuperator foil materials up to 850°C.

Romedenne, Marie↗

DOE OSTI2020

Steam oxidation of ytterbium disilicate environmental barrier coatings with and without a silicon bond coat

The current generation of multilayer Si/Yb 2 Si 2 O 7 environmental barrier coatings (EBCs) are temperature limited by the melting point of Si, 1414°C. To investigate higher temperature EBCs, the cyclic steam oxidation of EBCs comprised of a single layer of ytterbium disilicate (YbDS) was compared to multilayered Si/YbDS EBCs, both deposited on SiC substrates using atmospheric plasma spray. In this work, after 500 1-h cycles at 1300°C in 90 vol%H2O-10 vol%air with a gas velocity of 1.5 cm/s, both multilayer Si/YbDS and single layer YbDS grew thinner silica scales than bare SiC, with the single layer YbDS forming the thinnest scale. Both coatings remained fully adherent and showed no signs of delamination. Silica scales formed on the single layer coating were significantly more homogeneous and possessed a markedly lower degree of cracking compared to the multilayered EBC. The single layer EBC also was exposed at 1425°C in steam with a gas velocity of 14 cm/s in an alumina reaction tube. The EBC reduced specimen mass loss compared to bare SiC but formed an extensive 2nd phase aluminosilicate reaction product. A similar reaction product was observed to form on some regions of the bare SiC specimen and appeared to partially inhibit silica volatilization. The 1425°C steam exposures were repeated with a SiC reaction tube and no 2nd phase reaction product was observed to form on the single layer EBC or bare SiC.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Effect of Air Plasma Sprayed Flash Bond Coatings on Furnace Cycle Lifetime of Disks and Rods

Air plasma sprayed (APS) flash coatings on high velocity oxygen fuel (HVOF) bond coatings are well known to extend the lifetime of thermal barrier coatings (TBCs). Recent work compared flash coatings of NiCoCrAlY and NiCoCrAlYHfSi applied to both rods and disk substrates of alloy 247. For rod specimens, 100 h cycles were used at 1100 °C in wet air. Both flash coatings significantly improved the lifetime compared to HVOF-only and vacuum plasma spray (VPS)-only MCrAlY bond coatings with no statistical difference between the two flash coatings. For disk specimens tested in 1 h cycles at 1100 °C in wet air, the NiCoCrAlY flash coating significantly outperformed an HVOF-only NiCoCrAlYHfSi bond coating and a NiCoCrAlYHfSi flash coating. The flash coatings formed a mixed oxide-metal zone that appeared to inhibit crack formation and therefore extend lifetime. In addition to the flash coating increasing the bond coating roughness, the underlying HVOF layer acted as a source of Al for this intermixed zone and prevented the oxide from penetrating deeper into the bond coating. Here, the lower Y+Hf content in the Y-only flash coating appeared to minimize oxidation in the flash layer, thereby increasing the benefit compared to a NiCoCrAlYHfSi flash coating.

42 ENGINEERING↗

DOE OSTI2020

Effect of Pressure and Thermal Cycling on Long-Term Oxidation in CO 2 and Supercritical CO 2

Concentrating solar power plant designers are interested in supercritical CO 2 (sCO 2 ) for the power block to achieve > 50% electrical efficiency at > 700 °C. The goal of this project was to develop a long-term (> 100 kh) lifetime model for sCO 2 compatibility using 10–15 kh laboratory exposures. Three Ni-based alloys (625, 282 and 740H) and an advanced austenitic stainless steel were evaluated here in long-term exposures at 700–800 °C using 500-h cycles in laboratory air, 0.1 MPa industrial grade (IG) CO 2 and 30 MPa supercritical IG CO 2 and using 10-h cycles in 0.1 MPa IG CO 2 and O 2 . Mass change data and quantification of the oxide scale thickness and depth of internal attack after 1000–10,000 h exposures at 750 °C indicate that these materials are compatible with the sCO 2 environments with modeling used to predict long-term behavior. Comparison of the 0.1 and 30 MPa 500-h cycle results did not show a significant effect of pressure on the reaction, and no significant internal carburization was observed under these conditions, even for the stainless steel, suggesting that chromia scales may be better C diffusion barriers than expected. For the Ni-based alloys, thermal cycling to simulate the solar duty cycle did not result in scale spallation after 15 kh in 10-h cycles or 4 kh in 1-h cycles at 750 °C. However, the stainless steel specimens formed an Fe-rich oxide after ~ 1500-h cumulative exposure time in both 1- and 10-h cycles.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Characterization of the Benefit of APS Flash Coatings in Improving TBC Lifetime

The addition of an air plasma sprayed (APS) “flash” layer on top of a high velocity oxygen fuel (HVOF) bond coating has been shown to extend the lifetime of thermal barrier coatings. A series of furnace cycle tests (FCTs) has been conducted at 1100 °C in air + 10% H 2 O to study the benefit of flash coatings on rod and disk alloy 247 specimens and provide a better mechanistic understanding of their benefit. Flash coatings of NiCoCrAlY and NiCoCrAlYHfSi both improved the FCT lifetime of rod specimens tested in 100-h cycles and disk specimens tested in 1-h cycles. In 1-h cycles, the NiCoCrAlY flash coating significantly outperformed an HVOF-only NiCoCrAlYHfSi bond coating and a NiCoCrAlYHfSi flash coating. Both flash coatings increased the bond coating roughness compared to HVOF. During exposure, the flash layer formed an intermixed alumina-metal layer that appeared to inhibit crack formation. Using a time series of observations, the lower Y + Hf content in the Y-only flash coating appeared to reduce Al consumption. The HVOF layer acted as a source of Al for the adjacent mixed zone. A second series of specimens included a fully APS bond coating where oxide had penetrated through the entire coating to the substrate after only 100, 1-h cycles and lifetime was similar to an HVOF-only bond coating. The inner HVOF layer with the outer APS flash coating prevented this complete penetration from occurring.

Pint, Bruce↗

DOE OSTI2020

Computational Methods to Accelerate Development of Corrosion Resistant Coatings for Industrial Gas Turbines

Oxidation resistant overlay coatings protect the underlying superalloy component in industrial gas turbines from oxidation attack. Rate of depletion of the Al-rich β-phase in the bond coat governs the lifetime of these coatings. The applicability of a computational method in accelerating the development of corrosion resistant coatings and significantly reducing the extensive experimental effort to predict coating lifetimes and microstructural changes in three-coated Ni-based superalloys for real operational durations (20–40 kh) was undertaken in the present study. Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and electron microprobe analysis (EPMA) were employed to characterize MCrAlY-coated superalloy substrates (1483, 247 and X4) after exposure at 900 °C in air + 10% H 2 O for up to 20,000 h. The model predicted the longest coating lifetime for the coating on X4 substrate. Precipitation of γ' in the coatings was correctly predicted for all three coating systems. Additionally, the model was able to predict the formation of topologically close packed (TCP)-phases in the investigated coating systems.

Pillai, Rishi R.↗

DOE OSTI2020

Methane combustion over Ni/Ce x Zr 1-x O 2 catalysts: impact of ceria/zirconia ratio

In this work, a series of Ce x Zr 1–x O 2 (x=1, 0.83, 0.17, 0) supports and 2 wt.% Ni/Ce x Zr 1–x O 2 catalysts were synthesized and evaluated for CH 4 oxidation. The Ce x Zr 1–x O 2 supports showed moderate activity (T 50 =519-638°C) with CO by-product formation. Additionally, nickel incorporation onto Ce x Zr 1–x O 2 lowered the T 50 to 438–477°C and eliminated the formation of CO. The results indicated that moderate Zr doping improved the support oxygen storage capacity (OSC) and reducibility of the catalyst at low temperatures (H 2 -TPR) leading to an enhanced CH 4 combustion turnover frequency: Ni/ZrO 2 <Ni/Ce 0.17 Zr 0.83 O 2 <Ni/CeO 2 <Ni/Ce 0.83 Zr 0.17 O 2 . The apparent activation energies of Ni/Ce x Zr 1–x O 2 catalysts (87-92 kJ/mol) were much lower than the ones of Ce x Zr 1–x O 2 supports and Ni/quartz sand (111-120 kJ/mol) indicating that CH 4 oxidation is facilitated when Ni is deposited on Ce x Zr 1–x O 2 . Moreover, stability tests with H 2 O and CO 2 showed that Zr doping can improve the catalyst stability, while H 2 O had a stronger reversible inhibition effect than CO 2 for CH 4 combustion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Boron-hyperdoped silicon for the selective oxidative dehydrogenation of propane to propylene

Boron containing catalysts have great potential in the oxidative dehydrogenation of propane. Herein, a series of 15, 25 and 42 at% boron-hyperdoped silicon catalysts synthesized by laser pyrolysis was studied. Here, boron-hyperdoped silicon samples showed >6 times higher propylene productivity than commercial h-BN at 450 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Primary solidification of ternary compounds in Al-rich Al–Ce–Mn alloys

Primary solidification of ternary compounds Al 20 Mn 2 Ce and Al 10 Mn 2 Ce were analyzed through the coupling of the thermodynamic modeling and classic nucleation theory. Thermodynamic models of Al 20 Mn 2 Ce and Al 10 Mn 2 Ce were developed using the CALPHAD approach based on first-principles calculated enthalpy of formation and experimental data obtained from this work and the literature. The analysis suggested that despite the larger thermodynamic driving force for nucleation of Al 10 Mn 2 Ce, nucleation is preferred for the Al 20 Mn 2 Ce phase in the highly undercooled liquid due to its smaller interfacial energy. Therefore, manufacturing methods with rapid cooling rates will favor primary solidification of Al 20 Mn 2 Ce for Al-rich Al–Ce–Mn alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2020

The Impact of Impurities on Alloy Behavior in Supercritical CO 2 at 700 °C

As part of round robin testing, specimens of commercial alloys 316, 120, 625, and 740 were exposed to 20 MPa research grade CO 2 at 700 °C for up to 1500 h. The first set of specimens had higher mass gain likely due to impurities not flushed from the autoclave at startup. After this issue was corrected, an identical set of specimens exhibited lower mass gains for both the Fe- and Ni-based alloys. The differences in reaction products were characterized to understand the effect of impurities under these conditions. As suggested by the mass change, thicker oxides were formed in each case, primarily for the Fe-based alloys. Furthermore, for the Ni-based alloys, the difference was primarily in the transient stage of oxidation with no change in rate constant. Alloy 120 exhibited increased internal attack, and differences in the scale phases formed were characterized to better understand the effect of impurities. Alloy 740 primarily exhibited a greater depth of internal attack in the first run.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Onset of Fogging and Degradation in Polyvinyl Toluene-Based Scintillators

Plastic-based gamma-ray detector materials such as polyvinyl toluene (PVT) occasionally suffer from loss of optical light transmission due to internal defects or “fogging” when exposed to some environmental conditions over time. Fogging results in reduced scintillation light propagated to the photomultiplier tube for collection. Investigations of the physical cause of these defects and their associated environmental conditions are ongoing. The goal of this work was to characterize the signs and effects of fogging over a simulated 22-year lifespan of the PVT in outdoor environments. Here, two potential mitigation methods were also evaluated, and one successfully mitigated the phenomena.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Cement having stress-indicating properties

A system and method measures subterranean stress. The system and method includes a cement mixture that is mixed with water to set as a solid and a stress measuring-medium having piezospectroscopic properties that directly reveals stress in situ within the cement mixture in response to a photo stimulation. The stress measuring-medium combines with the cement mixture as a dry blend before being combined with water.

36 MATERIALS SCIENCE↗

NASA NTRS2002

Morphological Evolution and Weak Interface Development within CVD-Zirconia Coating Deposited on Hi-Nicalon Fiber

The phase contents and morphology of a ZrO2 fiber coating deposited at 1050 C on Hi-Nicalon(Tm) by chemical vapor deposition were examined as a function of deposition time from 5 to 120 min. The morphological evolution in the ZrO2 coating was correlated to the development of delamination within the ZrO2 coating. The delamination appears to occur as a result of: (1) continuous formation of tetragonal ZrO2 nuclei on the deposition surface; (2) martensitic transformation of the tetragonal phase to a monoclinic phase upon reaching a critical grain size; and (3) development of significant compressive hoop stresses due to the volume dilation associated with the transformation. Our observations suggest that it will be of critical importance to further understand and eventually control the nucleation and grain growth behavior of CVD ZrO2 and its phase transformation behavior for its potential applications for composites.

Li, Hao↗