Engineering topics

Lauer, H. V., Jr.

Publications and source records attributed to Lauer, H. V., Jr..

At least 37 records · Page 2

NASA NTRS1999

Differential Scanning Calorimetry and Evolved Gas Analysis of Hydromagnesite

Volatile-bearing minerals (e.g., Fe-oxyhydroxides, phyllosilicates, carbonates and sulfates) may be important phases on the surface of Mars. In order to characterize these phases the Thermal and Evolved Gas Analyzer (TEGA) flying on the Mars'98 lander will perform analyses on surface samples from Mars. Hydromagnesite [Mg5(CO3)4(OH)2.4H2O] is considered a good standard mineral to examine as a Mars soil analog component because it evolves both H2O and CO2 at temperatures between 0 and 600 C. Our aim here is to interpret the DSC signature of hydromagnesite under ambient pressure and 20 sccm N2 flow in the range 25 to 600 C. The DSC curve for hydromagnesite under the above conditions consists of three endothermic peaks at temperatures 296, 426, and 548 and one sharp exotherm at 511 C. X-ray analysis of the sample at different stop temperatures suggested that the exotherm corresponded with the formation of crystalline magnesite. The first endotherm was due to dehydration of hydromagnesite, and then the second one was due to the decomposition of carbonate, immediately followed by the formation of magnesite (exotherm) and its decomposition to periclase (last endotherm). Evolution of water and CO2 were consistent with the observed enthalpy changes. A library of such DSC-evolved gas curves for putative Martian minerals are currently being acquired in order to facilitate the interpretation of results obtained by a robotic lander.

Lauer, H. V., Jr.↗

NASA NTRS1997

Lepidocrocite to Maghemite to Hematite: A way to have Magnetic and Hematitic Martian Soil

We examined decomposition products of lepidocrocite, which were produced by heating the phase in air at temperatures up to 525 C for 3 and 300 hr, by XRD, TEM, magnetic methods, and reflectance spectroscopy (visible and near-IR). Single-crystal lepidocrocite particles dehydroxilated to polycrystalline particles of disordered maghemite which subsequently transformed to polycrystalline particles of hematite. Essentially pure maghemite was obtained at 265 and 223 C for the 3 and 300 hr heating experiments, respectively. Its saturation magnetization (J(sub s)) and mass specific susceptibility are approximately 50 A(sq m)/kg and approximately 40 cubic micrometers/kg, respectively. Because hematite is spectrally dominant, spectrally-hematitic samples (i.e., characterized bv a minimum near 860 nm and a maximum near 750 nm) could also be strongly magnetic (J(sub s) up to approximately 30 A(sq m)/kg) from the masked maghemite component. TEM analyses showed that individual particles are polycrystalline with respect to both maghemite and hematite. The spectrally-hematitic and magnetic Mh+Hm particles can satisfy the spectral and magnetic constraints for Martian surface materials over a wide range of values of Mh/(Mh+Hm) and as either pure oxide powders or (within limits) as components of multiphase particles. These experiments are consistent with lepidocrocite as the precursor of Mh+Hm assemblages on Mars, but other phases (e.g., magnetite) that decompose to Mh and Hm are also possible precursors. Simulations done with a copy of the Mars Pathfinder Magnet Array showed that spectrally hematitic Mh+Hm powders having J(sub s) equal to 20.6 A(sq m)/kg adhered to all five magnets.

Morris, Richard V.↗

NASA NTRS1996

The Origin of Eucrites: An Experimental Perspective

The origin of eucrites has been the subject of debate. At issue is whether high-Mg# eucrites such as Sioux County are primitive or evolved liquids. We believe that the problem of the origin of eucrites is essentially solved. Problems associated with the petrogenesis of other achondrite groups remain, but the eucrites, taken as a whole, seem to present a clear and understandable story that we will present using experiments, analyses, and calculations. The two traditional eucrite groupings, the partial melting trend a.k.a. Stannem trend) and the fractional crystallization trend (a.k.a. Nuevo Laredo trend) have both been reproduced experimentally. The partial melting trend culminates in Sioux County. Sioux County is also an acceptable starting point for the fractional crystallization trend. The implication of these experimental results is that it is extremely difficult to relate the eucrites to diogenites, a group of pyroxene cumulates that conceivably could have crystallized from eucrite parent magmas.

Jones, J. H.↗

NASA NTRS1995

Hematite, pyroxene, and phyllosilicates on Mars: Implications from oxidized impact melt rocks from Manicouagan Crater, Quebec, Canada

Visible and near-IR refectivity, Moessbauer, and X ray diffraction data were obtained on powders of impact melt rock from the Manicouagan Impact Crater located in Quebec, Canada. The iron mineralogy is dominated by pyroxene for the least oxidized samples and by hematite for the most oxidized samples. Phyllosilicate (smectite) contents up to approximately 15 wt % were found in some heavily oxidized samples. Nanophase hematite and/or paramagnetic ferric iron is observed in all samples. No hydrous ferric oxides (e.g., goethite, lepidocrocite, and ferrihydrite) were detected, which implies the alteration occurred above 250 C. Oxidative alteration is thought to have occurred predominantly during late-stage crystallization and subsolidus cooling of the impact melt by invasion of oxidizing vapors and/or solutions while the impact melt rocks were still hot. The near-IR band minimum correlated with the extent of aleration Fe(3+)/Fe(sub tot) and ranged from approximately 1000 nm (high-Ca pyroxene) to approximately 850 nm (bulk, well-crystalline hematite) for least and most oxidized samples, respectively. Intermediate band positions (900-920 nm) are attributed to low-Ca pyroxene and/or a composite band from hematite-pyroxene assemblages. Manicouagan data are consistent with previous assignments of hematite and pyroxene to the approximately 850 and approximately 1000nm bands observed in Martian reflectivity spectra. Manicouagan data also show that possible assignments for intermediate band positions (900-920 nm) in Martian spectra are pyroxene and/or hematite-pyroxene assemblages. By analogy with impact melt sheets and in agreement with observables for Mars, oxidative alteration of Martian impact melt sheets above 250 C and subsequent erosion could produce rocks and soils with variable proportions of hematite (both bulk and nanophase), pyroxene, and phyllosilicates as iron-bearing mineralogies. If this process is dominant, these phases on Mars were formed rapidly at relativly high temperatures on a sporadic basis throughout the history of the planet. The Manicouagan samples also show that this mineralogical diversity can be accomplished at constant chemical composition, which is also indicated for Mars from the analyses of soil at the two Viking landing sites.

Morris, Richard V.↗

NASA NTRS1995

Hematite, pyroxene, and phyllosilicates on Mars: Implications from oxidized impact melt rocks from Manicouagan Crater, Quebec, Canada

Visible and near-IR reflectivity, Mossbauer, and X ray diffraction data were obtained on powders of impact melt rock from the Manicouagan Impact Crater located in Quebec, Canada. The iron mineralogy is dominated by pyroxene for the least oxidized samples and by hematite for the most oxidized samples. Phyllosilicate (smectite) contents up to 15 wt % were found in some heavily oxidized samples. Nanophase hematite and/or paramagnetic ferric iron is observed in all samples. No hydrous ferric oxides (e.g., goethite, lepidocrocite, and ferrihydrite) were detected, which implies the alteration occurred above 250 C. Oxidative alteration is thought to have occurred predominantly during late-stage crystallization and subsolidus cooling of the impact melt by invasion of oxidizing vapors and/or solutions while the impact melt rocks were still hot. The near-IR band minimum correlated with the extent of aleration (Fe(3+)/Fe(sub tot)) and ranged from approx. 1000 nm (high-Ca pyroxene) to approx. 850 nm (bulk, well-crystalline hematite) for least and most oxidized samples, respectively. Intermediate band positions (900-920 nm) are attributed to low-Ca pyroxene and/or a composite band from hematite-pyroxene assemblages. Manicouagan data are consistent with previous assignments of hematite and pyroxene to the 850 and 1000 nm bands observed in Martian reflectivity spectra. Manicouagan data also show that possible assignments for intermediate band positions (900-920 nm) in Martian spectra are pyroxene and/or hematite-pyroxene assemblages. By analogy with impact melt sheets and in agreement with observables for Mars, oxidative alteration of Martian impact melt sheets above 250 C and subsequent erosion could produce rocks and soils with variable proportions of hematite (both bulk and nanophase), pyroxene, and phyllosilicates as iron-bearing mineralogies. If this process is dominant, these phases on Mars were formed rapidly at relatively high temperatures on a sporadic basis throughout the history of the planet. The Manicouagan samples also show that this mineralogical diversity can be accomplished at constant chemical composition, which is also indicated for Mars from analyses of soil at the two Viking landing sites.

Morris, Richard V.↗

NASA NTRS1995

Reflectivity and other physicochemical properties of Mn-substituted goethites and hematites

Goethite-bearing samples with values of Mn(s) (Mn/(Mn+Fe) mole fraction) up to 0.206 were synthesized by precipitation from alkaline solution. Samples with Mn(s) less than or equal 0.061 were single-phase Mn-goethites: samples with higher Mn(s) values contained another Mn-bearing phase (probably jacobsite). Mn-hematites were prepared by dehydroxylation of corresponding Mn-goethites at 500 C. Orthorhombic a and b unit cell dimensions of Mn-goethites changed in a linear manner with Mn(s), but not at rates predicted by the Vegrad law. Hexagonal unit cell dimensions of Mn-hematites did not vary with Mn(s). Moessbauer parameters isomer shift (IS), quadrupole splitting (QS), and hyperfine field (B(sub hf)) were measured at 293 and 15 K. For all single-phase Mn-goethites and Mn-hematites (Mn(s) less than or equal 0.061), magnetic splitting was observed at both temperatures. At 293 K, small but systematic decreases in B(sub hf) were observed with increasing Mn substitution; IS and QS were not dependent on Mn(s). Mn substitution strongly lowered the Morin transition temperature of hematite. At 15 K, the Morin transition was not present for Mn(s) greater than 0.020(4). The saturation magnetization of Mn-goethites and Mn-hematites (Mn(s) less than or equal 0.061) was the expected zero (within error) for antiferromagnetic goethite and for hematites obtained from dehydroxylation of goethites. Mn-geothites with Mn(s) greater than 0.061 were magnetic because of the presence of strongly magnetic jacobsite. For reflectivity spectra, bands resulting from MN(3+) were centered near 454 and 596 nm for Mn-goethites and near 545 and 700 nm for Mn-hematites. There is evidence for a approximately 700 nm band in spectral data for Martian bright regions, but association of it with Mn(3+) is not a unique interpretation. Comparison of laboratory and Martian spectral data implies that Mn(s) less than 0.032 for the Mn(3+) content of Martian hematites.

Vempati, R. K.↗

NASA NTRS1994

High Resolution Transmission Electron Microscopy (HRTEM) of nanophase ferric oxides

Iron oxide minerals are the prime candidates for Fe(III) signatures in remotely sensed Martian surface spectra. Magnetic, Mossbauer, and reflectance spectroscopy have been carried out in the laboratory in order to understand the mineralogical nature of Martian analog ferric oxide minerals of submicron or nanometer size range. Out of the iron oxide minerals studied, nanometer sized ferric oxides are promising candidates for possible Martian spectral analogs. 'Nanophase ferric oxide (np-Ox)' is a generic term for ferric oxide/oxihydroxide particles having nanoscale (less than 10 nm) particle dimensions. Ferrihydrite, superparamagnetic particles of hematite, maghemite and goethite, and nanometer sized particles of inherently paramagnetic lepidocrocite are all examples of nanophase ferric oxides. np-Ox particles in general do not give X-ray diffraction (XRD) patterns with well defined peaks and would often be classified as X-ray amorphous. Therefore, different np-Oxs preparations should be characterized using a more sensitive technique e.g., high resolution transmission electron microscopy (HRTEM). The purpose of this study is to report the particle size, morphology and crystalline order, of five np-Ox samples by HRTEM imaging and electron diffraction (ED).

Golden, D. C.↗

NASA NTRS1994

Mossbauer and spectral (visible and near-IR) data for Fe(3+)-substituted rutile

Titanohematite and rutile containing some Fe(3+) are possible highly oxidized weathering products of ilmenite and titanomagnetities. We report here Moessbauer and reflectivity data (visible and near-IR) for Fe(3+)-substituted rutile as a part of our continuing studies of ferric-substituted minerals that might have bearing on the interpretation of Martian spectral data.

Lauer, H. V., Jr.↗

NASA NTRS1994

Hematite formed from pyroxene on Mars by meteoritic impact

In earlier work, we showed using Mossbauer data that the mineralogy of iron-bearing phases in impact melt rocks from Manicouagan Crater (Quebec, Canada) is to a first approximation hematite and pyroxene. The visible and near-IR reflectivity data for these impact melt rocks show a continuous trend in band position from approximately 850 to approximately 1000 nm, which corresponds to the positions for the hematite and pyroxene endmembers, respectively. The oxidation is thought to occur shortly after the impact when oxidizing vapors and/or solutions reacted with the impact melt which was below its solidus temperature but still relatively hot. The reflectance data have important implications for Mars because band positions which occur between approximately 850 and 1000 nm bands observed for Mars can be attributed to hematite-pyroxene assemblages and not necessarily to different ferric mineralogy. Because oxidation of impact melt rocks at Manicouagan is thought to occur subsolidus, precursors for the hematite include oxides such as magnetite and ilmenite and silicates such as pyroxene and olivine. To determine if the Manicouagan impact-melt rocks are related to each other by simple thermal subsolidus oxidation, we calcined in air a relatively unoxidized Manicouagan impact-melt rock (MAN-74-608A). Previous work has shown that np-Hm (nanophase hematite) particles can be derived by calcination of iron-bearing silicates.

Morris, Richard V.↗

NASA NTRS1993

Microscopic iron metal on glass and minerals - A tool for studying regolith maturity

A novel method of producing mixtures of glass or minerals with iron metal is presented. A portion of the Fe(2+) in basaltic glass and minerals can be reduced to metal in a few hours at 1100 C and an oxygen fugacity well below the iron-wustite buffer. Part of the iron metals forms rounded submicrometer blebs on the surfaces and in some cases within the grains. A concentration of such blebs equivalent to 20-30 percent of a grain's surface area can totally dominate the reflectance spectra of basaltic glass, pyroxene, and olivine. The production of optically opaque iron metal blebs, combined with the decline in Fe(2+), affects the glass and mineral reflectance spectra in three ways: by lowering the overall reflectivity, reducing the spectral contrast of absorption features, and producing a continuum with a general rise in reflectivity toward longer wavelengths.

Allen, C. C.↗

NASA NTRS1993

Mineralogy of three slightly palagonitized basaltic tephra samples from the summit of Mauna Kea, Hawaii

The paper characterizes the mineralogy and spectral properties of three slightly palagonitized basaltic tephra samples collected near the summit of Mauna Kea in order to contribute to the basis for inferring mineralogy and processes for Martian surface materials. The mineralogy of size fractions of these samples is examined by diffuse reflectance and FIR spectroscopy, optical microscopy, X-ray diffraction, Moessbauer spectroscopy, magnetic analysis, EMPA, TEM, and SEM. For the 20-1000 micron size fraction, sample HWMK11 (red) is essentially completely oxidized and has a hematite (Ti-hematite) pigment dispersed throughout the silicate matrix. Sample HWMK12 (black) has the lowest proportion of ferric-bearing phases and is thus least weathered. For HWMK11, the amount of hematite is essentially constant, and mica is present only in the coarse clay-sized fraction; smectites are low in structural Fe.

Golden, D. C.↗

NASA NTRS1993

Effects of microscopic iron metal on the reflectance spectra of glass and minerals

Maturity, which is a measure of the time lunar soils have been in the upper approximately 1 mm of the surface, is correlated with changes in the soils' optical properties. Mature soil is darker and somewhat redder than immature soil of the same composition, and features in the reflectance spectrum become more subdued with increasing maturity. The maturation process also involves accumulation of agglutinitic glass and submicroscopic metallic iron particles. We have produced submicrometer iron metal blebs on the surface and within glass and mineral grains by the method of high-temperature reduction. This technique has permitted the determination of optical changes in samples much simpler than lunar soil, and offers a useful tool with which to investigate the maturation process.

Allen, C. C.↗

NASA NTRS1993

Terrestrial impact melts as analogues for the hematization of Martian surface materials

Visible and near-IR reflectivity and Mossbauer data were obtained on powders of hydrothermally-altered impact melt sheets from West Clearwater Lake, Manicouagan, and Ries (Polsingen) impact structures. The data support previous interpretations that Martian bright regions spectra can be interpreted by a ferric-bearing phase that has a relatively featureless absorption edge together with some well-crystalline (bulk) hematite to account for the 860 nm hematite band. The data also show that bands at wavelengths longer than 900 nm, which are characteristic of Martian dark regions, occur when both hematite and pyroxene are present. It thus follows that hematization of Mars can be attributed, at least in part, to hydrothermal alterations of impact melt sheets. Impact heating could also form bulk-Hm from nanophase ferric oxides.

Morris, R. V.↗

NASA NTRS1993

Mineralogical diversity (spectral reflectance and Moessbauer data) in compositionally similar impact melt rocks from Manicouagan Crater, Canada

Meteoritic impacts under oxidizing surface conditions occur on both earth and Mars. Oxidative alteration of impact melt sheets is reported at several terrestrial impact structures including Manicouagan, West Clearwater Lake, and the Ries Basin. A number of studies have advocated that a significant fraction of Martian soil may consist of erosional products of oxidatively altered impact melt sheets. If so, the signature of the Fe-bearing mineralogies formed by the process may be present in visible and near infrared reflectivity data for the Martian surface. Of concern is what mineral assemblages form in impact melt sheets produced under oxidizing conditions and what their spectral signatures are. Spectral and Moessbauer data for 19 powder samples of impact melt rock from Manicouagan Crater are reported. Results show for naturally occurring materials that composite hematite-pyroxene bands have minima in the 910-nm region. Thus many of the anomalous Phobos-2 spectra, characterized by a shallow band minimum in the near-IR whose position varies between approximately 850 and 1000 nm, can be explained by assemblages whose endmembers (hematite and pyroxene) are accepted to be present on Mars. Furthermore, results show that a mineralogically diverse suite of rocks can be generated at essentially constant composition, which implies that variations in Martian surface mineralogy do not necessarily imply variations in chemical composition.

Morris, R. V.↗

NASA NTRS1992

Location of nanophase Fe-oxides in palagonitic soils: Implication for Martian pigments

Palagonitic materials from Mauna Kea, Hawaii, were identified as Mars analogs based on their spectral and magnetic properties. These materials probably resulted from hydrothermal alteration during eruption of the volcano and/or from weathering under ambient conditions. The reflectance spectra of the Mars surface obtained by Earth-based telescopes and the reflectance spectra of analogs obtained in the laboratory show features due to electronic transitions of Fe(III) in oxide particles that range in size from nanometer (nanophase) to micrometer sized or larger. The presence of Fe(III) suggests oxidizing conditions during the alteration process in Mars that may have occurred in the past or during a slow ongoing process. Two naturally altered basaltic samples from Hawaii (HWMK12 and HWMK13) and a laboratory-altered (PH-13-DCGT2) basaltic glass similar in elemental composition to the above two samples was examined. All three samples exhibited spectral characteristics similar to martian bright-region spectra. Chemical and mineralogical changes occurring at the surface of these basalts were studied in order to understand the basis for their Mars-like properties. The spectral properties of the three samples were examined after the removal of Fe oxides by chemical extractants.

Golden, D. C.↗

NASA NTRS1992

Effect of DCB extraction on Mossbauer and spectral data for a Hawaiian palagonitic soil (PN-9): Iden tification of pigmentary phases

The study of palagonitic soils is an active area of research in martian geoscience because the spectral and magnetic properties of a subset are spectral and/or magnetic analogues of martian bright regions. An understanding of the composition, distribution, and mineralogy of ferric-bearing phases for palagonitic soils forms, through spectral and magnetic data, a basis for inferring the nature of ferric-bearing phases on Mars. Progress has been made in this area, but the data set is incomplete, especially with respect to the nature of pigmenting phases. The purpose of this study is to identify the nature of the pigment for Hawaiian palagonitic soil PN-9 by using extraction procedures to selectively remove iron oxide phases. This soil was collected at the same locale as samples Hawaii 34 and VOL02. All three soils are good spectral analogues for martian bright regions.

Morris, Richard V.↗

NASA NTRS1992

Mars surface weathering products and spectral analogs: Palagonites and synthetic iron minerals

There are several hypotheses regarding the formation of Martian surface fines. These surface fines are thought to be products of weathering processes occurring on Mars. Four major weathering environments of igneous rocks on Mars have been proposed; (1) impact induced hydrothermal alterations; (2) subpermafrost igneous intrusion; (3) solid-gas surface reactions; and (4) subaerial igneous intrusion over permafrost. Although one or more of these processes may be important on the Martian surface, one factor in common for all these processes is the reaction of solid or molten basalt with water (solid, liquid, or gas). These proposed processes, with the exception of solid-gas surface reactions, are transient processes. The most likely product of transient hydrothermal processes are layer silicates, zeolites, hydrous iron oxides and palagonites. The long-term instability of hydrous clay minerals under present Martian conditions has been predicted; however, the persistence of such minerals due to slow kinetics of dehydration, or entrapment in permafrost, where the activity of water is high, can not be excluded. Anhydrous oxides of iron (e.g., hematite and maghemite) are thought to be stable under present Martian surface conditions. Oxidative weathering of sulfide minerals associated with Martian basalts has been proposed. Weathering of sulfide minerals leads to a potentially acidic permafrost and the formation of Fe(3) oxides and sulfates. Weathering of basalts under acidic conditions may lead to the formation of kaolinite through metastable halloysite and metahalloysite. Kaolinite, if present, is thought to be a thermodynamically stable phase at the Martian surface. Fine materials on Mars are important in that they influence the surface spectral properties; these fines are globally distributed on Mars by the dust storms and this fraction will have the highest surface area which should act as a sink for most of the absorbed volatiles near the surface of Mars. Therefore, the objectives of this study were to: (1) examine the fine fraction mineralogy of several palagonitic materials from Hawaii; and (2) compare spectral properties of palagonites and submicron sized synthetic iron oxides with the spectral properties of the Martian surface.

Golden, D. C.↗

NASA NTRS1991

Transformation products of submicron-sized aluminum-substituted magnetite: Color and reductant solubility

Magnetite, when present as fine particles, is soluble in acid ammonium oxalate (pH equals 3). However, the commonly used extractant for free iron oxides (i.e., citrate dithionite-bicarbonate (CDB) is not very effective in dissolving magnetite in soils and geologic materials. Upon oxidation, magnetite transforms to maghemite; at elevated temperatures, maghemite inverts to hematite. This transformation causes a change in color from black to red and may affect the reductant solubility as well. The objectives here were to examine the color and reflectance spectral characteristics of products during the transformation of magnetite to maghemite to hematite and to study the effect of Al-substitution in magnetite on the above process. Reductant solubility of Al-substituted magnetite, maghemite, and hematite was also studied. In summary, the transformation of magnetite to maghemite was accompanied by a change in color from black to red because of the oxidation of Fe2(+) to Fe3(+). The phase change maghemite to hematite had a relatively minor effect on the color and the reflectance spectra.

Golden, D. C.↗