Search NASA⌕ Search

Engineering topics

Lei, Yu

Publications and source records attributed to Lei, Yu.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Recommendations to standardize reporting, execution, and interpretation of X-ray Absorption Spectroscopy measurements

In July of 2022, a National Science Foundation (NSF)- and US Department of Energy (DOE)-sponsored workshop was held on the topic of rigor and reproducibility (R&R) in thermal, heterogeneous catalysis. As a result of the workshop, a report has been published entitled "Addressing Rigor and Reproducibility in Thermal, Heterogeneous Catalysis"[1]. This manuscript summarizes one section of the report: "Recommendations for catalyst characterization by X-ray absorption spectroscopy". Here, the section focuses exclusively on X-ray absorption spectroscopy (XAS) and is narrowly focused on recommendations for the collection and interpretation of XAS data for routine experiments. Therefore, one should not expect a detailed guide for each different experiment that one may perform nor are the recommendations designed to be overly prescriptive. However, the report is designed to draw attention to key pitfalls and common problems in the collection, reporting, analysis and interpretation of XAS studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Direct Laser Writing of Multimetal Bifunctional Catalysts for Overall Water Splitting

Water electrolysis is of interest as a sustainable way to produce clean hydrogen and oxygen fuel and help mitigate the rising problems of climate change while meeting global energy demands. High-efficiency, stable, and earth-abundant bifunctional catalysts are needed to enable more effective electrochemical cells for the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Here, we investigate the synthesis, composition, performance, and mechanism of multimetal catalysts serving dual functionality in both OER and HER of water electrolysis. Through a laser synthesis method, we synthesized heterogeneous catalysts of nanocrystalline multimetallic alloy pockets embedded within an amorphous oxide matrix. We evaluated the performance and composition of a range of mixed transition-metal oxide materials for both OER and HER, ultimately synthesizing a Cr 0.01 Fe 0.27 Co 0.34 Ni 0.38 O x /C y catalyst that has a stable, high-rate, and competitive overall water splitting performance of 1.76 V at 100 mA cm –2 in an alkaline medium. Using density functional theory to gain insight as the active site and mechanism, we propose that the inclusion of a minor amount of Cr increases the degeneracy of energetic states that lowers the cost of forming the O 2 p–d bond and H 1 s–d bond due to the hybridization of s, p, and d orbitals from Cr. Using a two-electrode water electrolysis cell with a constant potential of 1.636 V to mimic the setup for fuel production, we found the catalyst to be stable at 14–15 mA cm –2 for 40 h. Furthermore, this laser synthesis method allowing for facile and rapid synthesis of complex multimetal systems demonstrates how doping a Fe, Co, and Ni heterogeneous amorphous/nanocrystalline structure with small amounts of Cr is important for bifunctional catalytic behavior, particularly for increasing HER functionality in advancing our understanding for future electrocatalytic design.

08 HYDROGEN↗
DOE OSTI2023

Synthesis of Pt 3 Zn 1 and Pt 1 Zn 1 intermetallic nanocatalysts for dehydrogenation of ethane

Pt 3 Zn 1 and Pt 1 Zn 1 intermetallic nanoparticles supported on SiO 2 were synthesized by combining atomic layer deposition (ALD) of ZnO, incipient wetness impregnation (IWI) of Pt, and appropriate hydrogen reduction. Here, the formation of Pt 1 Zn 1 and Pt 3 Zn 1 intermetallic nanoparticles was observed by both X-ray diffraction (XRD) and synchrotron X-ray absorption spectroscopy (XAS). STEM images showed that the 2–3 nm Pt-based intermetallic nanoparticles were uniformly dispersed on a SiO 2 support. The relationships between Pt–Zn intermetallic phases and synthesis conditions were established. In situ XAS measurements at Pt L 3 and Zn K edges during hydrogen reduction provided a detailed image of surface species evolution. Owing to a combined electronic and geometric effect, Pt 1 Zn 1 exhibited much higher reactivity and stability than Pt 3 Zn 1 and Pt in both the direct dehydrogenation and oxidative dehydrogenation of ethane to ethylene reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Spatial Control of Substitutional Dopants in Hexagonal Monolayer WS 2 : The Effect of Edge Termination

The ability to control the density and spatial distribution of substitutional dopants in semiconductors is crucial for achieving desired physicochemical properties. Substitutional doping with adjustable doping levels has been previously demonstrated in 2D transition metal dichalcogenides (TMDs); however, the spatial control of dopant distribution remains an open field. In this work, edge termination is demonstrated as an important characteristic of 2D TMD monocrystals that affects the distribution of substitutional dopants. Particularly, in chemical vapor deposition (CVD)-grown monolayer WS 2 , it is found that a higher density of transition metal dopants is always incorporated in sulfur-terminated domains when compared to tungsten-terminated domains. Here two representative examples demonstrate this spatial distribution control, including hexagonal iron- and vanadium-doped WS 2 monolayers. Density functional theory (DFT) calculations are further performed, indicating that the edge-dependent dopant distribution is due to a strong binding of tungsten atoms at tungsten-zigzag edges, resulting in the formation of open sites at sulfur-zigzag edges that enable preferential dopant incorporation. Based on these results, it is envisioned that edge termination in crystalline TMD monolayers can be utilized as a novel and effective knob for engineering the spatial distribution of substitutional dopants, leading to in-plane hetero-/multi-junctions that display fascinating electronic, optoelectronic, and magnetic properties.

2D transition metal dichalcogenides↗
DOE OSTI2021

Single-Step Direct Laser Writing of Multimetal Oxygen Evolution Catalysts from Liquid Precursors

We investigate a laser direct-write method to synthesize and deposit metastable, mixed transition metal oxides and evaluate their performance as oxygen evolution reaction catalysts. This laser processing method enabled the rapid synthesis of diverse heterogeneous alloy and oxide catalysts directly from cost-effective solution precursors, including catalysts with a high density of nanocrystalline metal alloy inclusions within an amorphous oxide matrix. The nanoscale heterogenous structures of the synthesized catalysts were consistent with reactive force-field Monte Carlo calculations. By evaluating the impact of varying transition metal oxide composition ratios, we created a stable Fe 0.63 Co 0.19 Ni 0.18 O x /C catalyst with a Tafel slope of 38.23 mV dec -1 and overpotential of 247 mV, a performance similar to that of IrO 2 . Synthesized Fe 0.63 Co 0.19 Ni 0.18 O x /C and Fe 0.14 Co 0.46 Ni 0.40 O x /C catalysts were experimentally compared in terms of catalytic performance and structural characteristics to determine that higher iron content and a less crystalline structure in the secondary matrix decreases the charge transfer resistance and thus is beneficial for electrocatalytic activity. Furthermore, this conclusion is supported by density-functional theory calculations showing distorted active sites in ternary metal catalysts are key for lowering overpotentials for the oxygen evolution reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Pathways of China's PM 2.5 air quality 2015–2060 in the context of carbon neutrality

Clean air policies in China have substantially reduced particulate matter (PM 2.5 ) air pollution in recent years, primarily by curbing end-of-pipe emissions. However, reaching the level of the World Health Organization (WHO) guidelines may instead depend upon the air quality co-benefits of ambitious climate action. Here, we assess pathways of Chinese PM 2.5 air quality from 2015 to 2060 under a combination of scenarios that link global and Chinese climate mitigation pathways (i.e. global 2°C- and 1.5°C-pathways, National Determined Contributions (NDC) pledges and carbon neutrality goals) to local clean air policies. We find that China can achieve both its near-term climate goals (peak emissions) and PM 2.5 air quality annual standard (35 μg/m3) by 2030 by fulfilling its NDC pledges and continuing air pollution control policies. However, the benefits of end-of-pipe control reductions are mostly exhausted by 2030, and reducing PM 2.5 exposure of the majority of the Chinese population to below 10 μg/m 3 by 2060 will likely require more ambitious climate mitigation efforts such as China's carbon neutrality goals and global 1.5°C-pathways. Our results thus highlight that China's carbon neutrality goals will play a critical role in reducing air pollution exposure to the level of the WHO guidelines and protecting public health.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Exposure, health effects, sensing, and remediation of the emerging PFAS contaminants – Scientific challenges and potential research directions

Per- and polyfluoroalkyl substances (PFAS) make up a large group of persistent anthropogenic chemicals which are difficult to degrade and/or destroy. PFAS are an emerging class of contaminants, but little is known about the long-term health effects related to exposure. In addition, technologies to identify levels of contamination in the environment and to remediate contaminated sites are currently inadequate. In this opinion-type discussion paper, a team of researchers from the University of Connecticut and the University at Albany discuss the scientific challenges in their specific but intertwined PFAS research areas, including rapid and low-cost detection, energy-saving remediation, the role of T helper cells in immunotoxicity, and the biochemical and molecular effects of PFAS among community residents with measurable PFAS concentrations. Potential research directions that may be employed to address those challenges and improve the understanding of sensing, remediation, exposure to, and health effects of PFAS are then presented. Here, we hope our account of emerging problems related to PFAS contamination will encourage a broad range of scientific experts to bring these research initiatives addressing PFAS into play on a national scale.

Challenges and research directions↗
DOE OSTI2020

Monolayer Vanadium‐Doped Tungsten Disulfide: A Room‐Temperature Dilute Magnetic Semiconductor

Abstract Dilute magnetic semiconductors (DMS), achieved through substitutional doping of spin‐polarized transition metals into semiconducting systems, enable experimental modulation of spin dynamics in ways that hold great promise for novel magneto–electric or magneto–optical devices, especially for two‐dimensional (2D) systems such as transition metal dichalcogenides that accentuate interactions and activate valley degrees of freedom. Practical applications of 2D magnetism will likely require room‐temperature operation, air stability, and (for magnetic semiconductors) the ability to achieve optimal doping levels without dopant aggregation. Here, room‐temperature ferromagnetic order obtained in semiconducting vanadium‐doped tungsten disulfide monolayers produced by a reliable single‐step film sulfidation method across an exceptionally wide range of vanadium concentrations, up to 12 at% with minimal dopant aggregation, is described. These monolayers develop p‐type transport as a function of vanadium incorporation and rapidly reach ambipolarity. Ferromagnetism peaks at an intermediate vanadium concentration of ~2 at% and decreases for higher concentrations, which is consistent with quenching due to orbital hybridization at closer vanadium–vanadium spacings, as supported by transmission electron microscopy, magnetometry, and first‐principles calculations. Room‐temperature 2D‐DMS provide a new component to expand the functional scope of van der Waals heterostructures and bring semiconducting magnetic 2D heterostructures into the realm of practical application.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Gold Catalysts Synthesized Using a Modified Incipient Wetness Impregnation Method for Propylene Epoxidation

Propylene epoxidation in the presence of oxygen and hydrogen were measured for a series of Au/TS-1 catalysts prepared by a modified incipient wetness impregnation (mIWI) method. This method enables precise control of the Au : Ti ratio in the Au/TS-1 catalysts. The optimized Au/TS-1 catalyst exhibited 12 % propylene conversion, 87 % PO selectivity, and 25 % hydrogen efficiency. The particle size of gold nanoparticles prepared by the modified IWI was between 2 and 3 nm, as demonstrated by XRD patterns, STEM images, and X-ray absorption spectroscopy at the Au L(3)edge. XPS spectra showed that the surface species on the catalysts were similar. UV-Vis spectra suggested that in the modified IWI method, the chlorine ligands in Au(Cl)(4)(-)were replaced by hydroxyl groups, which contributes to form small gold nanoparticles. Kinetic studies showed that the active sites of Au(mIWI)/TS-1 are similar to the Au(DP)/TS-1 prepared by deposition precipitation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Toward Long-Term Accurate and Continuous Monitoring of Nitrate in Wastewater Using Poly(tetrafluoroethylene) (PTFE)–Solid-State Ion-Selective Electrodes (S-ISEs)

Long-term accurate and continuous monitoring of nitrate (NO 3 – ) concentration in wastewater and groundwater is critical for determining treatment efficiency and tracking contaminant transport. Current nitrate monitoring technologies, including colorimetric, chromatographic, biometric, and electrochemical sensors, are not feasible for continuous monitoring. In this work, we addressed this challenge by modifying NO 3 – solid-state ion-selective electrodes (S-ISEs) with poly(tetrafluoroethylene) (PTFE, (C 2 F 4 ) n ). The PTFE-loaded S-ISE membrane polymer matrix reduces water layer formation between the membrane and electrode/solid contact, while paradoxically, the even more hydrophobic PTFE-loaded S-ISE membrane prevents bacterial attachment despite the opposite approach of hydrophilic modifications in other antifouling sensor designs. Specifically, an optimal ratio of 5% PTFE in the S-ISE polymer matrix was determined by a series of characterization tests in real wastewater. Five percent of PTFE alleviated biofouling to the sensor surface by enhancing the negative charge (–4.5 to –45.8 mV) and lowering surface roughness (Ra: 0.56 ± 0.02 nm). It simultaneously mitigated water layer formation between the membrane and electrode by increasing hydrophobicity (contact angle: 104°) and membrane adhesion and thus minimized the reading (mV) drift in the baseline sensitivity (“data drifting”). Long-term accuracy and durability of 5% PTFE-loaded NO 3 – S-ISEs were well demonstrated in real wastewater over 20 days, an improvement over commercial sensor longevity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Pursuing graphite-based K-ion O 2 batteries: a lesson from Li-ion batteries

The replacement of lithium metal by lithium intercalated graphite was crucial for developing safe lithium-ion batteries. Superoxide-based potassium–oxygen batteries represent an exciting metal–oxygen battery with the highest energy efficiencies. However, using potassium metal is a more serious safety threat than lithium. Herein, we explore the possibility of graphite-intercalation anodes for potassium-ion oxygen batteries (PIOBs) with enhanced safety. This work demonstrates for the first time that establishing an artificial potassium salt-rich solid electrolyte interphase (SEI) enables a reversible graphite-intercalation anode (249.6 mA h g -1 after 600 cycles) in a potassium bis(trifluoromethanesulfonyl)imide (KTFSI)-based localized high-concentration electrolyte. Such an electrolyte is stable with the superoxide cathode. The PIOB delivers energy efficiencies above 90% at a depth of discharge (DOD) of 25% for 80 cycles. A three-electrode measurement shows that its overpotential mainly comes from the anode. The lifespan is limited to the gradual degradation of the artificial SEI caused by oxygen crossover. This work represents a step towards achieving holistic anode–electrolyte–cathode compatibility in a PIOB and its realistic evaluation under a controlled DOD.

25 ENERGY STORAGE↗
DOE OSTI2020

Superconductivity enhancement in phase-engineered molybdenum carbide/disulfide vertical heterostructures

Stacking layers of atomically thin transition-metal carbides and two-dimensional (2D) semiconducting transition-metal dichalcogenides, could lead to nontrivial superconductivity and other unprecedented phenomena yet to be studied. In this work, superconducting α-phase thin molybdenum carbide flakes were first synthesized, and a subsequent sulfurization treatment induced the formation of vertical heterolayer systems consisting of different phases of molybdenum carbide—ranging from α to γ' and γ phases—in conjunction with molybdenum sulfide layers. These transition-metal carbide/disulfide heterostructures exhibited critical superconducting temperatures as high as 6 K, higher than that of the starting single-phased α-Mo 2 C (4 K). We analyzed possible interface configurations to explain the observed moiré patterns resulting from the vertical heterostacks. Our density-functional theory (DFT) calculations indicate that epitaxial strain and moiré patterns lead to a higher interfacial density of states, which favors superconductivity. Such engineered heterostructures might allow the coupling of superconductivity to the topologically nontrivial surface states featured by transition-metal carbide phases composing these heterostructures potentially leading to unconventional superconductivity. Moreover, we envisage that our approach could also be generalized to other metal carbide and nitride systems that could exhibit high-temperature superconductivity.

heterostructure↗
DOE OSTI2019

Wireless 3D Nanorod Composite Arrays based High Temperature Surface-Acoustic-Wave Sensors for Selective Gas Detection through Machine Learning Algorithms (Final Report)

This is the final scientific and technical report which summarizes the research conducted through this funded project. In this report, we first present the accomplishments of the project, major research activities and specific activities conducted, and then discuss the significant results. We also describe the opportunities for training and professional development provided to the involved students as well as the products produced. Finally, we report the impact of the research on the development of human resources and present the budgetary information.

42 ENGINEERING↗
DOE OSTI2019

Localized High‐Concentration Electrolytes Boost Potassium Storage in High‐Loading Graphite

Abstract Reversible intercalation of potassium‐ion (K + ) into graphite makes it a promising anode material for rechargeable potassium‐ion batteries (PIBs). However, the current graphite anodes in PIBs often suffer from poor cyclic stability with low coulombic efficiency. A stable solid electrolyte interphase (SEI) is necessary for stabilizing the large interlayer expansion during K + insertion. Herein, a localized high‐concentration electrolyte (LHCE) is designed by adding a highly fluorinated ether into the concentrated potassium bis(fluorosulfonyl)imide/dimethoxyethane, which forms a durable SEI on the graphite surface and enables highly reversible K + intercalation/deintercalation without solvent cointercalation. Furthermore, this LHCE shows a high ionic conductivity (13.6 mS cm −1 ) and excellent oxidation stability up to 5.3 V (vs K + /K), which enables compatibility with high‐voltage cathodes. The kinetics study reveals that K + intercalation/deintercalation does not follow the same pathway. The potassiated graphite exhibits excellent depotassiation rate capability, while the formation of a low stage intercalation compound is the rate‐limiting step during potassiation.

Qin, Lei↗
DOE OSTI2019

“Self-heating” enabled one-pot synthesis of fluorescent carbon dots

Instead of using traditional external heating treatment methods, a facile heating equipment-free method is developed for one-pot synthesis of fluorescent carbon dots (CDs) via exothermic crosslinking reaction enabled “self-heating” and further induced high degree of carbonization. The obtained CDs exhibit strong blue fluorescence and are well characterized through a series of advanced analysis, including their optical properties, surface morphology, and chemical compositions. The corresponding synthesis mechanism is also disscussed and proposed. Moreover, the as-synthesized carbon dots have been successfully applied for selective Fe 3+ detection as a simple demonstration. Fe 3+ can significantly quench the fluorescence signal of CDs, whereas other metal ions show insignificant effect on their fluorescence intensity. The quenching performance is ascribed to synergistic effect of electrostatic interaction between ferric ions and the fluorescent CDs as well as interaction induced electron transfer. Here, this study expands the cutting edge of simple synthesis of fluorescent CDs, where CDs hold great promises in sensing applications.

42 ENGINEERING↗